Electrospinning combined with hydrothermal synthesis and lithium storage properties of ZnFe2O4-graphene composite nanofibers

ZnFe₂O₄-graphene composite nanofibers were prepared through electrospinning technique, then with graphene oxide by the facile solvothermal method to get the final products for the first time. The obtained ZnFe₂O₄ nanofibers composed of numerous same size nanoparticles wrapped by graphene sheets to form a unique nanostructure. When the ZnFe₂O₄-graphene electrode was evaluated as anode for lithium-ion batteries, good rate capability and long-term cycling stability could be achieved. The ZnFe₂O₄-graphene electrode exhibited a first discharge capacity of 2166 mAh g⁻¹ cycling at 0.05 C, remained an average reversible capacity of 1000 mAh g⁻¹ after 50 cycles, and kept the high rate capacities of 899, 822, 760 and 711 mAh g⁻¹ at the current rates of 0.5, 1, 2 and 5 C, respectively. The excellent electrochemical performance could be ascribed to the following reasons: the large electrochemical active surface area provided by the composite nanofibers; the graphene sheets decreased the internal resistance of the lithium-ion batteries, which resulted from the electrical conductivity of the graphene sheets; the graphene sheets as conductive network could effectively restrain the agglomeration of ZnFe₂O₄ nanopaiticals.     

Exceptional electrochemical performance of nitrogen-doped porous carbon for lithium storage

Crumpled nitrogen-doped porous carbon sheets are successfully fabricated via chemical activation of polypyrrole-functionalized graphene sheets with KOH (APGs). The obtained APGs with nitrogen doping, high surface area, porous and crumpled structure exhibit exceptional electrochemical performances as the electrode material for LIBs, including a superhigh reversible specific capacity of 1516.2 mAh g⁻¹, excellent cycling stability over 10,000 cycles, and good rate capability (133.2 mAh g⁻¹ even at a very high current density of 40 A g⁻¹). The chemical activation synthesis strategy might open new avenues for the design of high-performance carbon-based anode materials.     

Dopamine derived nitrogen-doped carbon sheets as anode materials for high-performance sodium ion batteries

Designed as an anode material for sodium ion batteries, nitrogen-doped carbon sheets (NCSs) were successfully synthesized using graphene and dopamine as template and carbon precursor, respectively. The NCSs demonstrate high reversible capacity and excellent rate performance, delivering a high reversible capacity of 382 mAh g⁻¹ at 50 mA g⁻¹ after 55 cycles. Even up to 10 A g⁻¹, a rate capacity of 75 mAh g⁻¹ can be obtained. Furthermore, NCSs also have remarkable cycling stability with specific capacity of 165 mAh g⁻¹ after 600 cycles (under 200 mA g⁻¹). The excellent performance of NCSs can be ascribed to the nitrogen-doped two-dimension sheet structure.     

NiCo2O4 nanosheets and nanocones as additive-free anodes for high-performance Li-ion batteries

Development of novel electrode materials with high energy and power densities for lithium-ion batteries (LIBs) is the key to meet the demands of electric vehicles. Transition metal oxides that can react with large amounts of Li⁺ for electrochemical energy storage are considered promising anode materials for LIBs. In this work, NiCo₂O₄ nanosheets and nanocones on Ni foam have been synthesized via general hydrothermal growth and low-temperature annealing treatment. They exhibit high rate capacities and good cyclic performance as LIB anodes owing to their architecture design, which reduces ion and electron transport distance, expands the electrode–electrolyte contact, increases the structural stability, and buffers volume change during cycles. Notably, NiCo₂O₄ nanosheets deliver an initial capacity of 2239 mAh g⁻¹ and a rate capacity of 964 mAh g⁻¹ at current densities of 100 and 5000 mA g⁻¹, respectively. The corresponding values of nanocones are 1912 and 714 mAh g⁻¹. Hence, the as-synthesized NiCo₂O₄ nanosheets and nanocones, which are carbon-free and binder-free with higher energy densities and stronger connections between active materials and current collectors for better stability, are promising for use in advanced anodes for high-performance LIBs.     

Synthesis of Mn3O4/N-doped graphene hybrid and its improved electrochemical performance for lithium-ion batteries

Mn₃O₄/N-doped graphene (Mn₃O₄/NG) hybrids were synthesized by a simple one-pot hydrothermal process. The scanning electron microscopy (SEM), transition electron microscopy (TEM), X-ray powder diffraction (XRD), Thermogravimetric analysis (TG), Raman Spectroscopy and X-ray photoelectron spectroscopy (XPS) were used to characterize the microstructure, crystallinity and compositions. It is demonstrated that Mn₃O₄ nanoparticles are high-dispersely anchored onto the individual graphene nanosheets, and also found that, in contrast with pure Mn₃O₄ obtained without graphene added, the introduction of graphene effectively restricts the growth of Mn₃O₄ nanoparticles. Simultaneously, the anchored well-dispersed Mn₃O₄ nanoparticles also play a role as spacers in preventing the restacking of graphene sheets and producing abundant nanoscale porous channels. Hence, it is well anticipated that the accessibility and reactivity of electrolyte molecules with Mn₃O₄/NG electrode are highly improved during the electrochemical process. As the anode material for lithium ion batteries, the Mn₃O₄/NG hybrid electrode displays an outstanding reversible capacity of 1208.4 mAh g⁻¹ after 150 cycles at a current density of 88 mA g⁻¹, even still retained 284 mAh g⁻¹ at a high current density of 4400 mA g⁻¹ after 10 cycles, indicating the superior capacity retention, which is better than those of bare Mn₃O₄, and most other Mn₃O₄/C hybrids in reported literatures. Finally, the superior performance can be ascribed to the uniformly distribution of ultrafine Mn₃O₄ nanoparticles, successful nitrogen doping of graphene and favorable structures of the composites.     

A nest-like hierarchical porous V2O5 as a high-performance cathode material for Li-ion batteries

In this article, V₂O₅ with a novel nest-like hierarchical porous structure has been synthesized by a facile solvothermal method and investigated as cathode material for lithium-ion batteries. The nest-like V₂O₅ with a diameter of about 1.5 µm, was composed of interconnected nanosheets with a highly porous structure. Without other modification, the as-prepared V₂O₅ electrode exhibited superior capacity. An initial discharge capacity of 330 mAh g⁻¹ (at a current density of 100 mA g⁻¹) could be delivered and a stable discharge capacity of 240 mAh g⁻¹ after 50 cycles is maintained. The excellent performance was attributed to the hierarchical porous structure that could buffer against the local volume change and shorten the lithium-ions diffusion distance.     

Hydrazine hydrate-induced hydrothermal synthesis of MnFe2O4 nanoparticles dispersed on graphene as high-performance anode material for lithium ion batteries

Herein, a MnFe₂O₄/graphene (MnFe₂O₄/G) nanocomposite has been synthesized via a facile N₂H₄·H₂O-induced hydrothermal method. During the synthesis, N₂H₄·H₂O is employed to not only reduce graphene oxide to graphene, but also prevent the oxidation of Mn²⁺ in alkaline aqueous solution, thus ensuring the formation of MnFe₂O₄/G. Moreover, MnFe₂O₄ nanoparticles (5–20 nm) are uniformly anchored on graphene. MnFe₂O₄/G electrode delivers a large reversible capacity of 768 mA h g⁻¹ at 1 A g⁻¹ after 200 cycles and high rate capability of 517 mA h g⁻¹ at 5 A g⁻¹. MnFe₂O₄/G holds great promise as anode material in practical applications due to the outstanding electrochemical performance combined with the facile synthesis strategy.     

One-step microwave-assisted synthesis of Sb2O3/reduced graphene oxide composites as advanced anode materials for sodium-ion batteries

Sb₂O₃/reduced graphene oxide (RGO) composites were prepared through a facile microwave-assisted reduction of graphite oxide in SbCl₃ precursor solution, and investigated as anode material for sodium-ion batteries (SIBs). The experimental results show that a maximum specific capacity of 503 mA h g⁻¹ is achieved after 50 galvanostatic charge/discharge cycles at a current density of 100 mA g⁻¹ by optimizing the RGO content in the composites and an excellent rate performance is also obtained due to the synergistic effect between Sb₂O₃ and RGO. The high capacity, superior rate capability and excellent cycling performance of Sb₂O₃/RGO composites demonstrate their excellent sodium-ion storage ability and show their great potential as electrode materials for SIBs.     

Fe3O4 nanoparticles encapsulated in electrospun porous carbon fibers with a compact shell as high-performance anode for lithium ion batteries

Fe₃O₄ nanoparticles encapsulated in porous carbon fibers (Fe₃O₄@PCFs) as anode materials in lithium ion batteries are fabricated by a facile single-nozzle electrospinning technique followed by heat treatment. A mixed solution of polyacrylonitrile (PAN) and polystyrene (PS) containing Fe₃O₄ nanoparticles is utilized to prepare hybrid precursor fibers of Fe₃O₄@PS/PAN. The resulted porous Fe₃O₄/carbon hybrid fibers composed of compact carbon shell and Fe₃O₄-embeded honeycomb-like carbon core are formed due to the thermal decomposition of PS and PAN. The Fe₃O₄@PCF composite demonstrates an initial reversible capacity of 1015 mAh g⁻¹ with 84.4% capacity retention after 80 cycles at a current density of 0.2 A g⁻¹. This electrode also exhibits superior rate capability with current density increasing from 0.1 to 2.0 A g⁻¹, and capacity retention of 91% after 200 cycles at 2.0 A g⁻¹. The exceptionally high performances are attributed to the high electric conductivity and structural stability of the porous carbon fibers with unique structure, which not only buffers the volume change of Fe₃O₄ with the internal space, but also acts as high-efficient transport pathways for ions and electrons. Furthermore, the compact carbon shell can promote the formation of stable solid electrolyte interphase on the fiber surface.     

3D network-like porous MnCo2O4 by the sucrose-assisted combustion method for high-performance supercapacitors

3D network-like porous MnCo₂O₄ nanostructures have been successfully fabricated through a facile and scalable sucrose-assisted combustion route followed by calcination treatment. Benefiting from its advantages of the unique 3D network-like architectures with large specific surface area (216.15 m² g⁻¹), abundant mesoporosity (2–50 nm) and high electronic conductivity, the as-prepared MnCo₂O₄ electrode displays a high specific capacitance of 647.42 F g⁻¹ at a current density of 1 A g⁻¹, remarkable capacitance retention rate of 70.67% at current density of 10 A g⁻¹ compared with 1 A g⁻¹, and excellent cycle stability (only 6.32% loss after 3000 cycles). The excellent electrochemical performances coupled with facile and cost effective method will render the as-fabricated 3D network-like porous MnCo₂O₄ as a promising electrode material for supercapacitors.     

Simple self-assembly of SnS2 entrapped graphene aerogel and its enhanced lithium storage performance

In this work, SnS₂ nanoplates entrapped graphene aerogel has been successfully prepared by simple self-assembly of reduced graphene oxide obtained through mild chemical reduction. Structural and morphological investigations demonstrated that SnS₂ nanoplates are highly dispersed in the three dimensional (3D) porous graphene matrix. When served as anode material for lithium-ion batteries, the electrochemical properties of SnS₂/graphene aerogel (SnS₂/GA) were evaluated by galvanostatic discharge–charge tests, cyclic voltammetry and impedance spectroscopy measurement. Compared with pristine SnS₂, the SnS₂/GA nanocomposite achieved a much higher initial reversible capacity (1186 mAh g⁻¹), superior cyclic stability (1004 mAh g⁻¹ after 60 cycles, corresponding to 84.7% of the initial reversible capacity), as well as better rate capability (650 mAh g⁻¹ at a current density of 1000 mA g⁻¹). This significantly improved lithium storage performance can be attributed to the good integration of SnS₂ nanoplates with 3D porous graphene network, which can not only provide much more active sites and easy access for Li ions intercalation, but also prevent the aggregation of SnS₂ nanoplates and facilitate fast transportation of Li ions and surface electrons during the electrochemical process.     

Ag enhanced electrochemical performance for Na2Li2Ti6O14 anode in rechargeable lithium-ion batteries

Due to the characteristics of an electronic insulator, Na₂Li₂Ti₆O₁₄ always suffers from low electronic conductivity as anode material for lithium storage. Via Ag coating, Na₂Li₂Ti₆O₁₄@Ag is fabricated, which has higher electronic conductivity than bare Na₂Li₂Ti₆O₁₄. Enhancing the Ag coating content from 0.0 to 10.0 wt%, the surface of Na₂Li₂Ti₆O₁₄ is gradually deposited by Ag nanoparticles. At 6.0 wt%, a continuous Ag conductive layer is formed on Na₂Li₂Ti₆O₁₄. While, particle growth and aggregation take place when the Ag coating content reaches 10.0 wt%. As a result, Na₂Li₂Ti₆O₁₄@6.0 wt% Ag displays better cycle and rate properties than other samples. It can deliver a lithium storage capacity of 131.4 mAh g⁻¹ at 100 mA g⁻¹, 124.9 mAh g⁻¹ at 150 mA g⁻¹, 119.1 mAh g⁻¹ at 200 mA g⁻¹, 115.8 mAh g⁻¹ at 250 mA g⁻¹, 111.9 mAh g⁻¹ at 300 mA g⁻¹ and 109.4 mAh g⁻¹ at 350 mA g⁻¹, respectively.     

Facile synthesis of NiMn2O4 nanosheet arrays grown on nickel foam as novel electrode materials for high-performance supercapacitors

Nanostructured spinel NiMn₂O₄ arrays have been fabricated by a facile hydrothermal approach and further investigated as binder-free electrode for high-performance supercapacitors. Compared with Mn₃O₄, NiMn₂O₄ exhibited higher specific capacitances (662.5 F g⁻¹ and 370.5 F g⁻¹ in different electrolytes at the current density of 1 A g⁻¹) and excellent cycling stability (~96% capacitance retention after 1000 cycles) in a three-electrode system. Such a novel microstructure grown directly on the conductive substrate provided sufficient active sites for redox reaction resulting in their enhanced electrochemical behaviors. Their improved performances suggested that ultrathin sheet-like NiMn₂O₄ arrays on Ni foam substrate were a promising electrode material for supercapacitors.     

Unique porous yolk-shell structured Co3O4 anode for high performance lithium ion batteries

This paper introduces a unique porous yolk-shell structured Co₃O₄ microball, which is synthesized by spray pyrolysis from precursor solution with polyvinylpyrrolidone (PVP) additive. PVP acts as an organic template in the pyrolytic reaction facilitating the formation of yolk-shell structure. The electrochemical properties of porous yolk-shell Co₃O₄ microballs evaluated as anode materials for lithium ion batteries exhibit high initial columbic efficiency of 77.9% and high reversible capacity of 1025 mAh g⁻¹ with capacity retention of 98.8% after 150 cycles at 1 A g⁻¹. In contrast, the hollow microballs obtained without PVP addition show obvious capacity decay from 1033 to 748 mAh g⁻¹ after 150 cycles with the capacity retention of 72.3%. In addition, the microballs with porous yolk-shell structure exhibit better rate performance. The superior electrochemical performance is mainly attributed to the unique porous yolk-shell structure which provides large voids to buffer volume expansion and enlarge the contact area with the electrolyte, shortening the diffusion path of the lithium ions.     

Highly mesoporous LaNiO3/NiO composite with high specific surface area as a battery-type electrode

This study reports the fabrication and characterization of mesoporous LaNiO₃/NiO composite with a very high specific surface area for a battery-type electrode. The mesoporous LaNiO₃/NiO composite was synthesized via a sol–gel method by using silica gel as a template, the colloidal silica gel was obtained by the hydrolysis and polymerization of tetraethoxysilane in the presence of La and Ni salts. We investigated the structure and the electrochemical properties of mesoporous LaNiO₃/NiO composite in detail. The mesoporous composite sample showed a specific surface area of 372 m² g⁻¹ with 92.7% mesoporous area and displayed remarkable electrochemical performance as a battery-type electrode material for supercapacitor. The specific capacity values were found to be 237.2 mAh g⁻¹ at a current density of 1 A g⁻¹ and 128.6 mAh g⁻¹ at a high current density of 20 A g⁻¹ in 1 M KOH aqueous electrolyte. More importantly, this mesoporous composite also showed an excellent cycling performance with the retention of 92.6% specific capacitance after 60,000 charging and discharging cycles.     

Nitrogen-doped carbon-coated hierarchical Li4Ti5O12-TiO2 hybrid microspheres as excellent high rate anode of Li-ion battery

Nitrogen-doped carbon-coated Li₄Ti₅O₁₂-TiO₂ (LTO-TO) hybrid microspheres were prepared by heat treating the dry mixture of urea and chemically lithiated dandelion-like TiO₂ microspheres in a stainless steel autoclave at 550 °C for 5 h. The hybrid materials were tested as anode of Li-ion batteries. As compared to the pristine sample, the N-doped carbon-coated LTO-TO microspheres exhibited higher specific capacity at both low and high current rates. Discharge capacities of 184 and 123 mAh g⁻¹ were obtained at 0.2 C and 20 C, respectively. Moreover, the LTO-TO/C electrode showed excellent cycle performance, with a discharge capacity of 121.3 mAh g⁻¹ remained after 300 cycles at 5 C, corresponding to an average capacity degradation rate of 0.073% per cycle. These high specific capacity, excellent rate capability and cycle performance demonstrated the high potentiality of the N-doped carbon-coated LTO-TO microspheres as anode material of both energy storage-type and power-type Li-ion batteries.     

Simple fabrication of a Fe2O3/carbon composite for use in a high-performance lithium ion battery

A simple approach was developed for the fabrication of a Fe₂O₃/carbon composite by impregnating activated carbon with a ferric nitrate solution and calcinating it. The composite contains graphitic layers and 10 wt.% Fe₂O₃ particles of 20–50 nm in diameter. The composite has a high specific surface area of ∼828 m² g⁻¹ and when used as the anode in a lithium ion battery (LIB), it showed a reversible capacity of 623 mAh g⁻¹ for the first 100 cycles at 50 mA g⁻¹. A discharge capacity higher than 450 mAh g⁻¹ at 1000 mA g⁻¹ was recorded in rate performance testing. This highly improved reversible capacity and rate performance is attributed to the combination of (i) the formation of graphitic layers in the composite, which possibly improves the matrix electrical conductivity, (ii) the interconnected porous channels whose diameters ranges from the macro- to meso- pore, which increases lithium-ion mobility, and (iii) the Fe₂O₃ nanoparticles that facilitate the transport of electrons and shorten the distance for Li⁺ diffusion. This study provides a cost-effective, highly efficient means to fabricate materials which combine conducting carbon with nanoparticles of metal or metal oxide for the development of a high-performance LIB.     

Monolithic Fe2O3/graphene hybrid for highly efficient lithium storage and arsenic removal

We fabricated a monolithic Fe₂O₃/graphene hybrid directly by hydrothermal reaction of ferrous oxalate dihydrate and graphene oxide without using a reducing agent. The reduced graphene oxide formed an interconnected network structure that can be used as a support for homogeneous distribution of active Fe₂O₃ nanoparticles. The graphene network and the pore channels in the hybrid facilitate fast electron transfer and ion transport. This hybrid can be directly used as a free-standing anode for lithium ion batteries, which simplifies the fabrication procedure of electrodes, and also exhibited a high capacity of 1062 mA h g⁻¹ at 100 mA g⁻¹, high rate capability and excellent cyclic stability over 100 cycles. Furthermore, as a self-supported adsorbent, it provides a new idea on loading active materials to the suitable substrate, which can be used as a promising material for water purification due to its easy collection and excellent capability in removing As(V) from water. The results demonstrate the promising applications of bulk reduced assembly of graphene with functional metal oxides, which will be helpful for future development of graphene-based multifunctional materials.     

Hollow ZnSnO3 cubes@carbon/reduced graphene oxide ternary composite as anode of lithium ion batteries with enhanced electrochemical performance

The ternary composite, carbon coated hollow ZnSnO₃ (ZS@C) cubes encapsulated in reduced graphene oxide sheets (ZS@C/rGO), was synthesized via low-temperature coprecipitation and colloid electrostatic self-assembly. The uniform carbon-coating layer not only plays a role in buffering the volume change of ZnSnO₃ cubes in the charging/discharging processes, but also forms three-dimensional network with the cooperation of graphene to maintain the structural integrity and improve the electrical conductivity. The results show that the reduced graphene oxide sheets encapsulated ZS@C microcubes with a typical core-shell structure of ~700 nm in size exhibit an improved electrochemical performance compared with bare ZS@C microcubes. The ZS@C/rGO electrode delivered an initial discharge capacity of 1984 mA h g⁻¹ at a current density of 0.1 A g⁻¹ and maintained a capacity of 1040 mA h g⁻¹ after 45 cycles. High specific capacity and superior cycle stability indicate that the ZS@C/rGO composite has a great potential for the application of lithium-ion anode material.     

Reduced graphene oxide with superior cycling stability and rate capability for sodium storage

Sodium ion battery is a promising electrical energy storage system for sustainable energy storage applications due to the abundance of sodium resources and their low cost. In this communication, the electrochemical properties of sodium ion storage in reduced graphene oxide (RGO) were studied in an electrolyte consisting of 1 M NaClO₄ in propylene carbonate (PC). The experimental results show that the RGO anode allowed significant sodium ion insertion, leading to higher capacity at high current density compared to the previously reported results for carbon materials. This is due to the fact that RGO possesses higher electrical conductivity and is a more active host, with large interlayer distances and a disordered structure, enabling it to store a higher amount of Na ions. RGO anode exhibits high capacity combined with long-term cycling stability at high current densities, leading to reversible capacity as high as 174.3 mAh g⁻¹ at 0.2 C (40 mA g⁻¹), and even 93.3 mAh g⁻¹ at 1 C (200 mA g⁻¹) after 250 cycles. Furthermore, RGO could yield a high capacity of 141 mAh g⁻¹ at 0.2 C (40 mA g⁻¹) over 1000 cycles.