Investigation of morphology formation in SBS block copolymer/homopolystyrene blends

Polymer blends comprising a polystyrene‐block‐polybutadiene‐block‐polystyrene (SBS) block copolymer and atactic homopolystyrene (hPS) were investigated using injection molded and solution cast samples. The morphology of the materials was studied by means of transmission electron microscopy (TEM) and scanning force microscopy (SFM). Dynamic mechanical analysis (DMA) was used to characterize the phase behavior and the morphology formation of the block copolymer as well as of the SBS/hPS blends. The glass transition temperatures seem to strongly depend on the homogeneity of the corresponding phases. A distinct difference was found between the morphologies of the blends prepared by different methods. While the SBS block copolymer always shows a lamellar morphology in injection molded or as‐cast samples, the injection molded blends show a disturbance in the morphology consisting of alternating layers. In contrast, in the case of as‐cast samples, added hPS forms polystyrene domains dispersed in a matrix of the pure block copolymer. Regarding the change in the glass transition temperature, in the effective volume and in the interfacial volume obtained from DMA curves, the morphology formation of the injection molded samples (pure SBS block copolymer and the corresponding blends) was investigated. Two different structural models for the blends are proposed. Polym. Eng. Sci. 44:1534–1542, 2004. © 2004 Society of Plastics Engineers.     

Preparation and mechanical properties of clay/polystyrene‐block‐polybutadiene‐block‐polystyrene triblock copolymer (SBS) intercalated nanocomposites using organoclay containing stearic acid

Organoclays containing various amounts of stearic acid (SA) were synthesized, and clay/polystyrene‐block‐polybutadiene‐block‐polystyrene triblock copolymer (SBS) intercalated nanocomposites were prepared using organoclays containing SA by melt‐blending. Montmorillonite was the clay used, and both stearylamine and SA were used as surface modifiers. The amount of SA added was 0, 20, 50 and 100% of the cation‐exchange capacity (CEC). In this study, the effects of SA on the microstructure and mechanical properties of the clay/SBS nanocomposites were investigated. In clay/SBS with 100% CEC of SA, although no exfoliation of the clay occurred, the stacked clay layers were uniformly dispersed at the nanometer level (100–800 nm) without agglomeration. Clay/SBSs containing SA exhibited superior mechanical properties compared to clay/SBS without SA. It was found that SA effectively improved the clay dispersion in the SBS matrix and the mechanical properties of the clay/SBSs. Copyright © 2006 Society of Chemical Industry     

Morphology and rheological behavior of maltene–polymer blends. I. Effect of partial hydrogenation of poly(styrene‐block‐butadiene‐block‐styrene‐block)‐type copolymers

Because of the importance of the maltene–polymer interaction for the better performance of polymer‐modified asphalts, this article reports the effects of the molecular characteristics of two commercial poly(styrene‐block‐butadiene‐block‐styrene‐block) (SBS) polymers and their partially hydrogenated derivatives [poly{styrene‐block[(butadiene)_1?x–(ethylene‐co‐butylene)_x]‐block‐styrene‐block} (SBEBS)] on the morphology and rheological behavior of maltene–polymer blends (MPBs) with polymer concentrations of 3 and 10% (w/w). Each SBEBS and its parent SBS had the same molecular weight and polystyrene block size, but they differed from each other in the composition of the elastomeric block, which exhibited the semicrystalline characteristics of SBEBS. Maltenes were obtained from Ac‐20 asphalt (Pemex, Salamanca, Mexico), and the blends were prepared by a hot‐mixing procedure. Fluorescence microscopy images indicated that all the blends were heterogeneous, with polymer‐rich and maltene‐rich phases. The rheological behavior of the blends was determined from oscillatory shear flow data. An analysis of the storage modulus, loss modulus, complex modulus, and phase angle as a function of the oscillatory frequency at various temperatures allowed us to conclude that the maltenes behaved as pseudohomogeneous viscoelastic materials that could dissipate stress without presenting structural changes; moreover, all the MPBs were more viscoelastic than the neat maltenes, and this depended on both the characteristics and amount of the polymer. The MPBs prepared with SBEBS were more viscoelastic and possessed higher elasticity than those prepared with SBS. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Blending of styrene‐block‐butadiene‐block‐styrene copolymer with sulfonated vinyl aromatic polymers

Different polymers containing sulfonic groups attached to the phenyl rings were prepared by sulfonation of polystyrene (PS) and styrene‐block‐(ethylene‐co‐1‐butene)‐block‐styrene (SEBS). The sulfonation degree (SD) was varied between 1 and 20 mol% of the styrene units. Polyphase materials containing sulfonated units were prepared by blending styrene‐block‐butadiene‐block‐styrene (SBS), with both sulfonated PS and sulfonated SEBS in a Brabender mixer. Such a procedure was performed as an alternative route to direct sulfonation of SBS which is actually not selective towards benzene rings because of the great reactivity of the double bonds in polybutadiene (PB) blocks to sulfonation agents. Thermal and dynamic‐mechanic analysis, together with morphology characterization of the blends, is consistent with obtaining partially compatible blends characterized by higher T_g of the polystyrene domains and improved thermal stability. © 2001 Society of Chemical Industry     

Singlet oxygen generation and adhesive loss in stimuli‐responsive,fullerene‐polymer blends,containing polystyrene‐block‐polybutadiene‐block‐polystyrene and polystyrene‐block‐polyisoprene‐block‐polystyrene rubber‐based adhesives

The adhesive properties, as measured by bulk tack and peel strength analysis, were found to decrease in polystyrene‐block‐polybutadiene‐block‐polystyrene (SBS) and polystyrene‐block‐polyisoprene‐block‐polystyrene (SIS) PSA films containing common singlet oxygen generators, acridine, rose bengal, and C₆₀ fullerene, when irradiated with a tungsten halogen light in air. The addition of the singlet oxygen quencher, β‐carotene, to the C₆₀ fullerene samples was found to significantly deter the rate of adhesive loss in the fullerene‐SBS and ‐SIS PSA nanocomposites. The presence of oxygen was essential to the mechanism of adhesive loss and, in combination with the effects of singlet oxygen generators and a singlet oxygen scavenger, strongly supports a singlet‐oxygen mediated process. FTIR investigations of fullerene‐SBS and ‐SIS systems suggest the initial formation of peroxides which, upon further irradiation, lead to the generation of carbonyl‐containing compounds of a ketonic type after crosslinking. Rates of SBS and SIS C‐H abstraction were comparable and found to decrease when the high‐pressure, mercury xenon irradiation source was filtered to allow only light of λ > 390 nm. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Compatibilization of poly(vinyl chloride) with polyamide and with polyolefin by using poly(lauryllactam‐random‐caprolactam‐block‐caprolactone)

The compatibilization of various poly(vinyl chloride) (PVC) blends was investigated. The blend systems were PVC‐polyamide 12 (PA12), PVC‐polypropylene (PP), and PVC‐ethylene‐propylene‐diene rubber (EPDM) with a new compatibilizing agent, random‐block terpolymer poly(ω‐lauryllactam‐random‐?‐caprolactam‐block‐?‐caprolactone) or systems containing these copolymers. The results were compared to those obtained in previous studies using poly(ω‐lauryllactam‐block‐?‐caprolactone) copolymer. The new block copolymer was specially synthesized by reactive extrusion. Observation by scanning electron microscopy (SEM) revealed that compatibilized blends had a finer morphology than the noncompatibilized blends. Addition of 10 weight percent (wt%) of block copolymer proved to be sufficient to give a significant improvement of the mechanical properties of the immiscible PVC blends at room temperature and at high temperatures that were above the glass transition temperature of PVC. For polyolefins, a three‐component compatibilizing system including maleated polypropylene, polyamide 12, and block copolymer was used. It was found that poly(ω‐lauryllactam‐random‐?‐caprolactam‐block‐?‐caprolactone) was the more efficient compatibilizing agent for the modification of PVC‐polyamide 12, PVC‐polypropylene, and PVC‐ethylene‐propylene‐diene rubber blends. J. VINYL. ADDIT. TECHNOL., 11:95–110, 2005. © 2005 Society of Plastics Engineers     

Crystal behavior of semicrystalline polystyrene‐block‐poly(l‐lactide) diblock copolymer in thin films with various structures

The crystal behavior of a semicrystalline polystyrene‐block‐poly(l ‐lactide) diblock copolymer in phase‐separated thin films with various thicknesses at different crystal temperatures has been investigated using atomic force microscopy and transmission electronic microscopy. Parallel and perpendicular lamellae could be obtained by annealing the thin films for different periods of time as reported previously (Chen et al., Macromolecules 40:6631 (2007)). At different temperatures, crystallization in thin films with parallel lamellar structure in the melt state gives dendrite crystals with orthorhombic structure, and the ordered structure in the melt is destroyed after crystallization. When crystallization occurs in thin films with perpendicular lamellar structure, crystal morphology and structure are greatly affected by the crystallization temperature (T_c). When T_c < T_g,ps, where T_g,ps is the glass transition temperature of a polystyrene block, crystallization is hardly confined within the lamellae. The morphology is preserved but the long period of the perpendicular lamellae is increased after crystallization. When T_c > T_g,ps, rod‐like crystals dominate the final morphology, and crystallinity destroys completely the structure in the melt.© 2012 Society of Chemical Industry     

Nanophase morphology and crystallization in poly(vinylidene fluoride)/polydimethylsiloxane‐block‐poly(methyl methacrylate)‐block‐polystyrene blends

An approach to achieve confined crystallization of ferroelectric semicrystalline poly(vinylidene fluoride) (PVDF) was investigated. A novel polydimethylsiloxane‐block‐poly(methyl methacrylate)‐block‐polystyrene (PDMS‐b‐PMMA‐b‐PS) triblock copolymer was synthesized by the atom‐transfer radical polymerization method and blended with PVDF. Miscibility, crystallization and morphology of the PVDF/PDMS‐b‐PMMA‐b‐PS blends were studied within the whole range of concentration. In this A‐b‐B‐b‐C/D type of triblock copolymer/homopolymer system, crystallizable PVDF (D) and PMMA (B) middle block are miscible because of specific intermolecular interactions while A block (PDMS) and C block (PS) are immiscible with PVDF. Nanostructured morphology is formed via self‐assembly, displaying a variety of phase structures and semicrystalline morphologies. Crystallization at 145 °C reveals that both α and β crystalline phases of PVDF are present in PVDF/PDMS‐b‐PMMA‐b‐PS blends. Incorporation of the triblock copolymer decreases the degree of crystallization and enhances the proportion of β to α phase of semicrystalline PVDF. Introduction of PDMS‐b‐PMMA‐b‐PS triblock copolymer to PVDF makes the crystalline structures compact and confines the crystal size. Moreover, small‐angle X‐ray scattering results indicate that the immiscible PDMS as a soft block and PS as a hard block are localized in PVDF crystalline structures. © 2019 Society of Chemical Industry     

Correlation between artificial and natural weathering tests on polystyrene‐block‐polybutadiene‐block‐polystyrene block copolymer

The effects of artificial and natural weathering tests on the structure and mechanical properties of polystyrene‐block‐polybutadiene‐block‐polystyrene (SBS) block copolymer were studied by spectrophotometry, Fourier Transform Infrared (FTIR) Spectroscopy, hardness measurements, and tensile testing. The correlation between artificial and natural weathering tests was also investigated. The results showed that the surface of SBS became yellow with increasing aging time. FTIR spectra confirmed the formation of carbonyl group in the aging process. The elongation at break, the tensile strength, and the tear strength decreased rapidly in the initial stage of the aging process and then leveled off, while the hardness increased with aging time. The correlation between artificial and natural weathering tests in Wanning and Hailaer, in China, could be expressed in terms of t₁ = 2.50t₀^1.99 and t₂ = 1.92t₀^2.56, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.     

Cure kinetics and thermal stability of micro and nanostructured thermosetting blends of epoxy resin and epoxidized styrene‐block‐butadiene‐block‐styrene triblock copolymer systems

The compatibility of styrene‐block‐butadiene‐block‐styrene (SBS) triblockcopolymer in epoxy resin is increased by the epoxidation of butadiene segment, using hydrogen peroxide in the presence of an in situ prepared catalyst in water/dichloroethane biphasic system. Highly epoxidized SBS (epoxy content SBS >26 mol%) give rise to nanostructured blends with epoxy resin. The cure kinetics of micro and nanostructured blends of epoxy resin [diglycidyl ether of bisphenol A; (DGEBA)]/amine curing agent [4,4′‐diaminodiphenylmethane (DDM)] with epoxidized styrene‐block‐butadiene‐block‐styrene (eSBS 47 mol%) triblock copolymer has been studied for the first time using differential scanning calorimetry under isothermal conditions to determine the reaction kinetic parameters such as kinetic constants and activation energy. The cure reaction rate is decreased with increasing the concentration of eSBS in the blends and also with the lowering of cure temperature. The compatibility of eSBS in epoxy resin is investigated in detailed by Fourier transform infrared spectroscopy, optical and transmition electron microscopic analysis. The experimental data of the cure behavior for the systems, epoxy/DDM and epoxy/eSBS(47 mol%)/DDM show an autocatalytic behavior regardless of the presence of eSBS in agreement with Kamal's model. The thermal stability of cured resins is also evaluated using thermogravimetry in nitrogen atmosphere. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Self‐assembled structures in polystyrene‐block‐polyisoprene‐blend‐polystyrene and polystyrene‐block‐poly(methyl methacrylate)‐blend‐polystyrene or ‐blend‐poly(methyl methacrylate) in the strong segregation regime

This study deals with the investigation of microphase‐separated morphology and phase behaviour in blends of polystyrene‐block‐polyisoprene with homopolystyrene and blends of polystyrene‐block‐poly(methyl methacrylate) with homopoly(methyl methacrylate) or homopolystyrene in the strong segregation regime using small‐angle X‐ray scattering and transmission electron microscopy as a function of composition, molecular weight of homopolymers, r_M and temperature. Parameter r_M = M_H/M_C (where M_H is the molecular weight of homopolymer and M_C that of the corresponding block copolymer) was selected to encompass behaviour of the chains denoted as a ‘wet brush’ (i.e. r_M < 1). The relative domain spacing D/D_o increases in the regime 0 < r_M?1 with increasing concentration of homopolymer w_P and increasing r_M but depends on the specific implemented morphology. We tested a new approximate D/D_o versus w_P relation in the strong segregation regime using block copolymers of high molecular weights. It is shown that the parameters r_M and χ^3/2N determine the slope of the D/D_o versus w_P relation in the strong segregation regime and the new approximation generally matches the experimental data better than the approximations used so far. Copyright © 2010 Society of Chemical Industry     

Influence of the incorporation of fine calcium carbonate particles on the impact strength of polypropylene/polystyrene‐block‐poly(ethylene butene)‐block‐polystyrene blends

The Izod impact strength of two kinds of ternary composites was investigated. One consisted of polypropylene (PP), the triblock copolymer polystyrene‐block‐poly(ethylene butene)‐block‐polystyrene (SEBS), and calcium carbonate (CaCO₃) particles, and the other consisted of PP, carboxylated SEBS (C‐SEBS), and CaCO₃ particles. The mean size of the CaCO₃ particles was about 160 nm. According to scanning electron microscopy observations, the composite with SEBS showed a morphology in which SEBS domains and CaCO₃ particles were independently dispersed in the PP matrix. On the other hand, the composite with C‐SEBS showed a morphology in which CaCO₃ particles were encapsulated by C‐SEBS; that is, a core–shell structure was formed. The Izod impact strength of the composite with SEBS was higher than that of the composite with C‐SEBS and the PP/SEBS and PP/C‐SEBS binary blends. According to observations of the fractured surface, the stress‐whitened area was larger in the composite with SEBS than in the composite with C‐SEBS and the PP/SEBS and PP/C‐SEBS binary blends. The toughening mechanism of the composite, using nanometer‐sized CaCO₃ particles in combination with SEBS, was examined. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

In the melt,grafting of polycarbonate onto polystyrene‐block‐poly(ethylene‐butylene)‐block‐polystyrene‐grafted‐maleic anhydride: Reactive extrusion

The use of reactions between polycarbonate (PC) and polystyrene‐block‐poly(ethylene‐butylene)‐block‐polystyrene‐ grafted‐maleic anhydride (SEBS‐g‐MAH) is a convenient way to create SEBS‐g‐PC. Grafting was realized by reactive extrusion at three temperatures using SnOct₂ or TBD catalysts. SEC analyses showed the apparition of a double distribution when the TBD was used. The mean residence time widely increased when this catalyst was used, and the rheological curves depicted a percolation effect of the SEBS nodules in the PC matrix. No explicit evolution was found with the use of SnOct₂. The thermal analyses showed the disappearance of the PC phase transition temperature. The Van Gurp‐Palmen plots confirmed the efficiency of the TBD catalyst and that 260°C was the optimal reactive extrusion temperature. POLYM. ENG. SCI., 54:2660–2668, 2014. © 2013 Society of Plastics Engineers     

Property enhancement in polypropylene ternary blend nanocomposites via a novel poly(ethylene oxide)‐grafted polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene toughener–compatibilizer system

Synthesis and characterization of a novel toughener–compatibilizer for polypropylene (PP)–montmorillonite (MMT) nanocomposites were conducted to provide enhanced mechanical and thermal properties. Poly(ethylene oxide) (PEO) blocks were synthetically grafted onto maleic anhydride‐grafted polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene (SEBS‐g‐MA). Special attention was paid to emphasize the effect of PEO‐grafted SEBS (SEBS‐g‐PEO) against SEBS‐g‐MA on morphology, static/dynamic mechanical properties and surface hydrophilicity of the resultant blends and nanocomposites. It was found that the silicate layers of neat MMT are well separated by PEO chains chemically bonded to nonpolar SEBS polymer without needing any organophilic modification of the clay as confirmed by X‐ray diffraction and transmission electron microscopy analyses. From scanning electron microscopy analyses, elastomeric domains interacting with MMT layers via PEO sites were found to be distributed in the PP matrix with higher number and smaller sizes than the corresponding blend. As a benefit of PEO grafting, SEBS‐g‐PEO‐containing nanocomposite exhibited not only higher toughness/impact strength but also increased creep recovery, as compared to corresponding SEBS‐g‐MA‐containing nanocomposite and neat PP. The damping parameter of the same nanocomposite was also found to be high in a broad range of temperatures as another advantage of the SEBS‐g‐PEO toughener–compatibilizer. The water contact angles of the blends and nanocomposites were found to be lower than that of neat hydrophobic PP which is desirable for finishing processes such as dyeing and coating. © 2018 Society of Chemical Industry     

Morphology of poly(styrene‐block‐dimethylsiloxane) copolymer films

The morphologies of poly(styrene‐block‐di‐methylsiloxane) (PS‐b‐PDMS) copolymer thin films were analyzed via atomic force microscopy and transition electron microscopy (TEM). The asymmetric copolymer thin films spin‐cast from toluene onto mica presented meshlike structures, which were different from the spherical structures from TEM measurements. The annealing temperature affected the surface morphology of the PS‐b‐PDMS copolymer thin films; the polydimethylsiloxane (PDMS) phases at the surface were increased when the annealing temperature was higher than the PDMS glass‐transition temperature. The morphologies of the PS‐b‐PDMS copolymer thin films were different from solvent to solvent; for thin films spin‐cast from toluene, the polystyrene (PS) phase appeared as pits in the PDMS matrix, whereas the thin films spin‐cast from cyclohexane solutions exhibited an islandlike structure and small, separated PS phases as protrusions over the macroscopically flat surface. The microphase structure of the PS‐b‐PDMS copolymer thin films was also strongly influenced by the different substrates; for an asymmetric block copolymer thin film, the PDMS and PS phases on a silicon substrate presented a lamellar structure parallel to the surface at intervals. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1010–1018, 2007     

Poly(styrene‐block‐butadiene‐block‐styrene‐block‐butadiene) and poly(styrene‐block‐butadiene‐block‐methyl methacrylate) copolymers as compatibilizers in PPO–SAN blends. I. Morphology and fracture behavior

The toughness behavior of PPO–SAN blends with the modifier poly(styrene‐block‐butadiene) (SBSB) and with poly(styrene‐block‐butadiene‐block‐methyl methacrylate) copolymers (SBM) under impact loading conditions has been investigated. The observed morphology of blends compatibilized with SBM, in which the rubber phase discontinuously accumulated at the PPO–SAN interface, correlated with about 20 times higher energy dissipation up to maximum force and about seven times higher deformation capacity compared to pure PPO–SAN blends. In contrast, the fracture behavior of the SBSB‐modified blends was not as strongly dependent on the rubber content. It is especially noteworthy that although the SBM modification resulted in a strong increase in toughness of the PPO–SAN blends, no decrease in stiffness could be found with up to 15% rubber additions. The values of Young's moduli remained at the same high level of the nonmodified material. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2037–2045, 2000     

Investigation of the rheological and mechanical properties of a polystyrene‐polyisobutylene‐polystyrene triblock copolymer and its blends with polystyrene

The rheological and mechanical properties of a polystyrene‐polyisobutylene‐polystyrene (SIBS) block copolymer containing 30 wt% polystyrene (PS) and its blends with PS (SIBS/PS) were investigated. Atomic Force Microscopy (AFM) was used to visualize the nanostructured phase morphology of the SIBS, which is responsible for the mechanical strength of this thermoplastic rubber. The order‐disorder transition (ODT) for the SIBS block copolymer was found to be above 250°C. SIBS/PS blends with 10–30 wt% PS showed improved moduli and tensile strengths. Blends containing up to 40 wt% PS behaved as thermoplastic elastomers. In the region of linear viscoelasticity the blends revealed pronounced non‐Newtonian behavior and enhanced elasticity. This paper also reports the role of this styrenic block copolymer in the impact modification of PS.     

Synthesis and characterization of novel polystyrene‐block‐polyurethane‐block‐polystyrene tri‐block copolymers through atom transfer radical polymerization

Background: Radical polymerization is used widely to polymerize more than 70% of vinyl monomers in industry, but the control over molecular weight and end group of the resulting polymers is always a challenging task with this method. To prepare polymers with desired molecular weight and end groups, many controlled radical polymerization (CRP) ideas have been proposed over the last decade. Atom transfer radical polymerization (ATRP) is one of the successful CRP techniques. Using ATRP, there is no report on the synthesis of polystyrene‐block‐polyurethane‐block‐polystyrene (PSt‐b‐PU‐b‐PSt) tri‐block copolymers. Hence this paper describes the method of synthesizing these tri‐block copolymers. To accomplish this, first telechelic bromo‐terminated polyurethane was synthesized and used further to synthesize PSt‐b‐PU‐b‐PSt tri‐block copolymers using CuBr as a catalyst and N,N,N,N″,N″‐pentamethyldiethylenetriamine as a complexing agent. Results: The ‘living’ nature of the initiating system was confirmed by linear increase of number‐average molecular weight and conversion with time. A semi‐logarithmic kinetics plot shows that the concentration of propagating radical is steady. The results from nuclear magnetic resonance spectroscopy, gel permeation chromatography and differential scanning calorimetry show that the novel PSt‐b‐PU‐b‐PSt tri‐block copolymers were formed through the ATRP mechanism. Conclusion: For the first time, PSt‐b‐PU‐b‐PSt tri‐block copolymers were synthesized through ATRP. The advantage of this method is that the controlled incorporation of polystyrene block in polyurethane can be achieved by simply changing the polymerization time. Copyright © 2007 Society of Chemical Industry     

Wetting behaviour and direct observation of thermally responsive polystyrene‐block‐poly(N‐isopropylacrylamide)‐block‐polystyrene electrospun fibres in aqueous environment

Electrospun fibres of thermally responsive triblock copolymer polystyrene‐block‐poly(N‐isopropylacrylamide)‐block‐polystyrene were prepared. Fibre morphology and swelling were studied below and above the lower critical solution temperature of poly(N‐isopropylacrylamide) (PNIPAM) using cryo‐electron microscopy. Cryo‐transmission electron microscopy showed that the fibre diameter increased up to 150% after immersion in water at 20 °C. In contrast, at 45 °C the fibre diameter increased considerably less. The sessile drop technique was used to characterize temperature‐dependent wetting of fibre mats. Contact angle (θ_CA) measurements revealed that a block copolymer fibre mat changed from hydrophobic (θ_CA > 90°) to hydrophilic (θ_CA < 90°) state within seconds after applying a water droplet on it at 20 °C. At 40 °C the initial contact angle was measured to be higher (135°) and it decreased much less than at 20 °C during the first minute of measurement. We observed using scanning electron microscopy that the electrospun fibres of the block copolymer having 77 wt% of PNIPAM lost their cylindrical shape and changed from fibres to thin sheets at both 20 and 40 °C within seconds after applying water on the fibres. Fibres having 55 wt% of PNIPAM were observed to be stable in water at both 20 and 40 °C, which resulted, surprisingly, in fibre mats with the strongest effects on thermally sensitive wetting. We discuss the surprising results and the implications that the evolution of fibre surface roughness has on the long‐term wetting behaviour, demonstrating a self‐adaptable hydrophilicity/hydrophobicity nature of the fibre mats. © 2013 Society of Chemical Industry     

Toughening of epoxy thermosets with polystyrene‐block‐polybutadiene‐block‐ polystyrene triblock copolymer via formation of nanostructures

In this contribution, we reported to utilize polystyrene‐block‐polybutadiene‐block‐polystyrene (PS‐b‐PB‐b‐PS), a commercial triblock copolymer to toughen epoxy thermosets. First, a PS‐b‐PB‐b‐PS triblock copolymer was chemically modified with hydroboration‐oxidation reaction, with which the midblock was hydroxylated whereas the endblocks remained unaffected. It was found that the degree of hydroxylation was well controlled. One of the hydroxylated PS‐b‐PB‐b‐PS samples was then used as the macromolecular initiator to synthesize a poly(ε‐caprolactone)‐grafted PS‐b‐PB‐b‐PS via the ring‐opening polymerization. It was found that the PS‐b‐PB‐b‐PS with poly(ε‐caprolactone) grafts can be successfully employed to nanostructure epoxy thermosets; the “core‐shell” microdomains composed of PB and PS were generated in the nanostructured thermosets. The nanostructured thermosets displayed improved fracture toughness. POLYM. ENG. SCI., 59:2387–2396, 2019. © 2019 Society of Plastics Engineers