Structural parameters and oxygen ion conductivity of Y2O3–ZrO2 and MgO–ZrO2 at high temperature

The oxygen ion conductivity of zirconia-based solid electrolytes doped with 8 mol% Y₂O₃–ZrO₂ (YSZ) and 9 mol% MgO–ZrO₂ (Mg-PSZ) at high temperature was investigated in terms of their thermal behavior and structural changes. At room temperature, YSZ showed a single phase with a fluorite cubic structure, whereas Mg-PSZ had a mixture of cubic, tetragonal and some monoclinic phases. YSZ exhibited higher ionic conductivity than Mg-PSZ at temperatures from 600 °C to 1250 °C because of the existence of the single cubic structure and low activation energy. A considerable increase in the conductivity with increasing temperature was observed in Mg-PSZ, which showed higher ionic conductivity than YSZ within the higher temperature range of 1300–1500 °C. A monoclinic-to-tetragonal phase transformation was found in Mg-PSZ and the lattice parameter of the cubic phase increased at 1200 °C. The phase transformation and the large lattice free volume contributed to the significant enhancement of the ionic conductivity of Mg-PSZ at high temperatures.     

Cyclic thermal shock resistance of h-BN composite ceramics with La2O3–Al2O3–SiO2 addition

The effects of La₂O₃–Al₂O₃–SiO₂ addition on the thermal conductivity, coefficient of thermal expansion (CTE), Young's modulus and cyclic thermal shock resistance of hot-pressed h-BN composite ceramics were investigated. The samples were heated to 1000 °C and then quenched to room temperature with 1–50 cycles, and the residual flexural strength was used to evaluate cyclic thermal shock resistance. h-BN composite ceramics containing 10 vol% La₂O₃–Al₂O₃ and 20 vol% SiO₂ addition exhibited the highest flexural strength, thermal conductivity and relatively low CTE, which were beneficial to the excellent thermal shock resistance. In addition, the viscous amorphous phase of ternary La₂O₃–Al₂O₃–SiO₂ system could accommodate and relax thermal stress contributing to the high thermal shock resistance. Therefore, the residual flexural strength still maintained the value of 234.3 MPa (86.9% of initial strength) after 50 cycles of thermal shock.     

Effects of Y2O3/MgO ratio on mechanical properties and thermal conductivity of silicon nitride ceramics

In this work, the effects of Y₂O₃/MgO ratio on the densification behavior, phase transformation, microstructure evolution, mechanical properties, and thermal conductivity of Si₃N₄ ceramics were investigated. Densified samples with bimodal microstructure could be obtained by adjusting the ratio of Y₂O₃/MgO. It was found that a low Y₂O₃/MgO ratio facilitated the densification of Si₃N₄ ceramics while a high Y₂O₃/MgO ratio benefited the phase transformation of Si₃N₄ ceramics. Best mechanical properties (flexural strength of 875 MPa, and fracture toughness of 8.25 MPa·m^1/2, respectively) and optimal thermal conductivity of 98.04W/(m·K) were achieved in the sample fabricated with Y₂O₃/MgO ratio of 3:4 by sintering at 1900°C for 4 h.     

Effect of Sm2O3 on microstructure,thermal shock resistance and thermal conductivity of cordierite-mullite-corundum composite ceramics for solar heat transmission pipeline

Cordierite-mullite-corundum composite ceramics for solar heat transmission pipeline were fabricated via pressureless sintering at a low sintering temperature with added Sm₂O₃. The effects of Sm₂O₃ on sintering behaviors, mechanical property, phase transformation, microstructure, thermal shock resistance and thermal conductivity of the composite ceramics were investigated. TEM analysis results demonstrated that Sm³⁺ located in glass and grain boundaries to facilitate the densification via the liquid-phase sintering mechanism and improve bending strength by grain refinement, respectively. Proper addition (3 wt%) of Sm₂O₃ could promote the crystallization of cordierite, and improve thermal shock resistance of the composite ceramics with an increasing rate of 16.70% for bending strength after 30 thermal shock cycles (air cooling from 1100 °C to RT). The composite ceramics possessed a superior thermal shock resistance, where a large amount of particles were formed to suppress crack initiation and propagation during thermal shock. Cordierite-mullite-corundum composite ceramics with proper Sm₂O₃ addition (3 wt%) had a lower thermal conductivity than that of composite ceramics without Sm₂O₃ addition by strengthening the scattering of phonon, which could reduce the heat loss during solar heat transmission process.     

Scavenging effect on ionic conduction behaviour at the grain boundary of MgO partially stabilised zirconia

The scavenging effect of magnesium oxide (MgO) addition on electrical property of 9 mol-% MgO partially stabilised zirconia (Mg-PSZ) was investigated in terms of phase transformation and intergranular phase formation. The addition of MgO up to 5 mol-% caused a stabilisation of Mg-PSZ, which led to an increase in the cubic phase and a decrease in the monoclinic and tetragonal phases in Mg-PSZ. The Mg-PSZ with the addition of 5 mol-% of MgO also exhibited the maximum ionic conductivity (0.3915?S?cm^?1 at 1500°C) and forsterite (Mg₂SiO₄) was observed on the grain boundaries of Mg-PSZ. The intergranular phases, formed by reactions between the silicon in Mg-PSZ and MgO addition, reduced the grain boundary resistance, because the siliceous phase which is a hindrance for oxygen ion conduction was scavenged by the formation of Mg₂SiO₄.     

Effects of Ho3+ concentration on the fabrication and properties of Ho: Y2O3-MgO nanocomposite for Mid-infrared laser applications

Infrared transparent Ho: Y₂O₃-MgO nanocomposite ceramics with a volume ratio of 50:50 (RE₂O₃: MgO) were prepared by combining sol-gel powder synthesis and hot-pressing sintering techniques. In order to obtain Ho: Y₂O₃-MgO nanocomposite ceramics with fine grain size, dense microstructure and homogeneous phase domains, the effect of sintering temperature and Ho³⁺ doping concentration were studied. Transmittance and SEM measurement revealed that the grain size of 3 at.% Ho: Y₂O₃-MgO ceramic sintered at 1250 °C is 141 nm, and the transmission is up to 85.2% at 5 μm. The detailed spectroscopic investigation of x at.% Ho: Y₂O₃-MgO (x = 1, 3, 5, 7, 9, 15) ceramics was performed. The nanocomposites exhibited photoluminescence properties similar to that of Ho: Y₂O₃ crystals and ceramics. In addition, the thermal conductivity of 3 at.% Ho: Y₂O₃-MgO ceramic is 13.04 W/m·K, which is superior to that of Ho:Y₂O₃ ceramics. The high transmission, excellent thermal conductivity, and outstanding optical characteristics indicated that Ho: Y₂O₃-MgO ceramics is a promising material for efficient infrared solid-state laser.     

Porous fibrous ZrO2-mullite ceramics prepared via tert-butyl alcohol-based gel-casting

Mullite fiber was used to fabricate ZrO₂-mullite based porous ceramic via tert-butyl alcohol (TBA)-based gel-casting process using zirconite and bauxite as raw materials. Phase compositions, microstructure, pore size distribution, linear shrinkage, bulk density, apparent porosity, thermal conductivity, and compressive strength were analyzed to investigate influences of mullite fiber content and added Y₂O₃ on prepared porous ceramics. Results show that bird nest-like three-dimensional fibrous reticular skeleton structure was constructed with mullite fibers that evenly enwrapped rod-like mullite and ZrO₂ grains. Prepared porous fibrous ZrO₂-mullite ceramics had narrow pore size distribution that consisted of mullite and m-ZrO₂. With an increase in mullite fiber content, linear shrinkage and bulk density decreased, apparent porosity increased, and relatively good thermal conductivity was obtained. In addition, added Y₂O₃ reacted with Al₂O₃ and SiO₂ to form Y-Al-Si-O glass phase, which promoted sintering and densification of the ceramic, thus improving its compressive strength.     

Fabrication of high thermal conductivity silicon nitride ceramics by pressureless sintering with MgO and Y2O3 as sintering additives

The fabrication of silicon nitride (Si₃N₄) ceramics with a high thermal conductivity was investigated by pressureless sintering at 1800 °C for 4 h in a nitrogen atmosphere with MgO and Y₂O₃ as sintering additives. The phase compositions, relative densities, microstructures, and thermal conductivities of the obtained Si₃N₄ ceramics were investigated systemically. It was found that at the optimal MgO/Y₂O₃ ratio of 3/6, the relative density and thermal conductivity of the obtained Si₃N₄ ceramic doped with 9 wt% sintering aids reached 98.2% and 71.51 W/(m·K), respectively. EDS element mapping showed the distributions of yttrium, magnesium and oxygen elements. The Si₃N₄ ceramics containing rod-like grains and grain boundaries were fabricated by focused ion beam technique. TEM observations revealed that magnesium existed as an amorphous phase and that yttrium produced a new secondary phase.     

Effect of CaF2 on sintering behavior and thermal shock resistance of Y2O3 materials

Y₂O₃ materials have become a popular candidate for preparing refractory crucibles for ultra-pure high-temperature alloy melting in recent years. However, its difficulty in sintering and poor thermal shock resistance limited its industrial application. The effect of CaF₂ on the densification microstructure, mechanical properties, and thermal shock resistance of Y₂O₃ materials was investigated in this paper. The main purpose of this study was to optimize the amount of CaF₂ added in the preparation of Y₂O₃ materials to improve its thermal shock resistance and get better mechanical properties. The mechanism of the densification process of CaF₂-doped Y₂O₃ materials was analyzed by phase analysis and microstructure. The results showed that successive doping of large Ca²⁺ ions caused more lattice distortion in the Y₂O₃ materials, and the diffusion rate of Y³⁺ was increased, thus enhanced grain boundary diffusion and promoted sintering densification in the Y₂O₃ materials. Meanwhile, the addition of CaF₂ also significantly reduced the apparent porosity and enhanced the mechanical properties of the materials. The improvement of these properties was attributed to the increased relative density of CaF₂-doped Y₂O₃ materials and the high sintering activity of CaF₂. In addition, crack deflections effectively improved the thermal shock resistance of the materials. The residual flexural strength ratio of Y₂O₃ materials doped with 1 wt % CaF₂ was increased by 21.2% after thermal shock test compared with undoped specimens.     

Effects of yttria and magnesia on densification and thermal conductivity of sintered reaction-bonded silicon nitrides

A variety of combinations of Y₂O₃ and MgO were used as additives in preparing Si₃N₄ ceramics by the sintering of reaction-bonded silicon nitride (SRBSN) method. By varying the amount of Y₂O₃ in the range of 0-5 mol% and that of MgO in the range of 0-8 mol%, the effects of Y₂O₃ and MgO additives on nitridation and sintering behaviors as well as thermal conductivity were studied. It was found that appropriate amount and combination of Y₂O₃ and MgO additives were essential for attaining full densification and achieving high thermal conductivity. The sample doped with 2.5 mol% of Y₂O₃ and 5 mol% of MgO attained a thermal conductivity of 128 Wm⁻¹K⁻¹ when sintered at 1900°C for 6 hours, and the sample doped with 2 mol% of Y₂O₃ and 4 mol% of MgO achieved a thermal conductivity of 156 Wm⁻¹K⁻¹ when sintered for 24 hours.     

Fabrication and thermal conductivity of AlN/BN ceramics by spark plasma sintering

Aluminum nitride/boron nitride (AlN/BN) ceramics with 15–30 vol.% BN as secondary phase were fabricated by spark plasma sintering (SPS), using Yttrium oxide (Y₂O₃) as sintering aid. Effects of Y₂O₃ content and the SPS temperature on the density, phase composition, microstructure and thermal conductivity of the ceramics were investigated. The results revealed that with increasing the amount of starting Y₂O₃ in AlN/BN, Yttrium-contained compounds were significantly removed after SPS process, which caused decreasing of the residual grain boundary phase in the sintered samples. As a result, thermal conductivity of AlN/BN ceramics was remarkably improved. By addition of Y₂O₃ content from 3 wt.% to 8 wt.% into AlN/15 vol.% BN ceramics, the thermal conductivity increased from 110 W/m K to 141 W/m K.     

Parameters influencing thermal shock resistance and ionic conductivity of 8 mol% yttria-stabilized zirconia (8YSZ) with dispersed second phases of alumina or mullite

Improved thermal shock resistance for cubic 8 mol% yttria-stabilized zirconia (8YSZ) used in fuel cells and oxygen sensors can be achieved by the addition of higher thermal conductivity second phases. This work compares 10–20 vol% alumina (α-Al₂O₃) and mullite (3Al₂O₃·2SiO₂) additions that increase thermal conductivity, reduce grain size, and increase strength and fracture toughness of 8YSZ. Improvements in thermal shock behavior correlate best with increased thermal conductivity. Second phase additions result in a smaller grain size that reduces the ionic conductivity, measured by electrochemical impedance spectroscopy, primarily through the creation of a higher density of blocking grain boundaries. The blocking effect correlates with decreasing grain size in 8YSZ but also is strongly influenced by the wetting behavior and distribution of intergranular phases. The addition of an appropriate dilute second phase of higher thermal conductivity, however, may compensate for a slightly lower ionic conductivity in certain applications such as oxygen sensors.     

Preparation and sealing effects of Mg–Al–Si–Ba–O-based glass-ceramic coatings on NTC thermistors

Herein, Mg–Al–Si–Ba–O-based glass ceramics were studied as potential candidates to protect Mn–Co–Ni–O-based negative temperature coefficient (NTC) thermistors at high temperatures such as 900 °C. The ceramics were prepared in three glass formulations (1#: 15MgO–15Al₂O₃-44.7SiO₂–25BaO, 2#: 17MgO–17Al₂O₃–41SiO₂–25BaO and 3#: 17MgO–17Al₂O₃–41SiO₂–20BaO–5Y₂O₃ (in mol%)) and their glass-transition temperatures (T_g) were determined using the differential scanning calorimetry (DSC) method. Scanning electronic microscopy (SEM) and X-ray diffraction (XRD) were used to characterize the parent glasses and glass-ceramic coatings. The sealing effects of the glass ceramics were examined by conducting an insulation test. The glass-ceramic sealing structures were subjected to 1000 thermal shock cycles at temperatures varying from room temperature to 900 °C. Notably, the sealing structure of glass-ceramic coating 1# was compact at a T_g of 760.9 °C. The glass-ceramic coatings effectively maintained the NTC properties of the sensitive ceramics in all three formulations. Interestingly, the glass-ceramic coating 3# containing Y₂O₃ demonstrated an increase in electrical resistance. Both the NTC thermistors coated with 1# and 2# glass formulations successfully passed 1000 thermal shock cycles without visible failures, and their resistance change ratios were well below the requisite 20%.     

Effect of a new nonoxide additive,Y3Si2C2, on the thermal conductivity and mechanical properties of Si3N4 ceramics

Enhancement of the thermal conductivity of silicon nitride is usually achieved by sacrificing its mechanical properties (bending strength). In this study, β-Si₃N₄ ceramics were prepared using self-synthesized Y₃Si₂C₂ and MgO as sintering additives. It was found that the thermal conductivity of the Si₃N₄ ceramics was remarkably improved without sacrificing their mechanical properties. The microstructure and properties of the Si₃N₄ ceramics were analyzed and compared with those of the Y₂O₃-MgO additives. The addition of Y₃Si₂C₂ eliminated the inherent SiO₂ and introduced nitrogen to increase the N/O ratio of the grain-boundary phase, inducing Si₃N₄ grain growth, increasing Si₃N₄ grain contiguity, and reducing lattice oxygen content in Si₃N₄. Therefore, by replacing Y₂O₃ with Y₃Si₂C₂, the thermal conductivity of the Si₃N₄ ceramics was significantly increased by 31.5% from 85 to 111.8Wm⁻¹K⁻¹, but the bending strength only slightly decreased from 704 ± 63MPa to 669 ± 33MPa.     

Effect of YF3 on densification behavior and thermal conductivity of AlN ceramics with Y2O3–YF3 additives under reducing atmosphere

The effect of yttrium fluoride (YF₃) on the densification behavior, microstructure, phase composition and thermal conductivity of aluminium nitride (AlN) ceramics with yttrium oxide (Y₂O₃) and YF₃ additives were studied. Since YF₃ provided liquid phases and promoted densification at a lower temperature, the sintering temperature required to reach the full density of AlN samples decreased with the increase in YF₃ content. Appropriate addition of YF₃ could improve the thermal conductivity of AlN ceramics, but the values of thermal conductivity decreased as YF₃ increased further. It is attributed to the ability of YF₃ to react with oxygen impurity was worse than that of Y₂O₃. Moreover, the reducing atmosphere significantly affected the phase composition, and the oxygen content in grain boundary phases decreased at 1750 °C and 1800 °C. Therefore, the proper proportion of Y₂O₃–YF₃ additives could simultaneously improve densification and the thermal conductivity of AlN samples at a low sintering temperature.     

Anisotropic properties of textured h-BN matrix ceramics prepared using 3Y2O3-5Al2O3(-4MgO) as sintering additives

Textured hexagonal boron nitride (h-BN) matrix composite ceramics were prepared by hot pressing using 3Y₂O₃-5Al₂O₃ (mole ratio of 3:5) and 3Y₂O₃-5Al₂O₃-4MgO (mole ratio of 3:5:4) as liquid phase sintering additives, respectively. During the sintering process with liquid phase environments, platelike h-BN grains were rotated to be perpendicular to the sintering pressure, forming the preferred orientation with the c-axis parallel to the sintering pressure. Both h-BN matrix ceramic specimens show significant texture microstructures and anisotropic mechanical and thermal properties. The h-BN matrix ceramics prepared with 3Y₂O₃-5Al₂O₃-4MgO possess higher texture degree and better mechanical properties. While the anisotropy of thermal conductivities of that prepared with 3Y₂O₃-5Al₂O₃ is more significant. The phase compositions and degree of grain orientation are the key factors that affect their anisotropic properties.     

Some thermomechanical properties of pure oxide ceramics

Conclusions The proposed vacuum furnace makes it possible to determine the deformation temperature under load and the coefficient of thermal expansion to high temperatures.Ceramics of pure oxides, Al₂O₃, ZrO₂, MgO, and BeO, have high temperatures of softening under load. The temperature of initial softening of Al₂O₃ ceramics containing additives lies in the range 1860–1930°C. The magnesia and beryllia specimens show high softening temperatures under load, but in vacuum at high temperatures they are very volatile. The initial softening temperature of ZrO₂ is about 2250°C.The linear expansion of pure-oxide ceramics reaches 2–3% at 1800–2000°C. Values obtained for the average coefficients of expansion for Al₂,O₃, ZrO₂, MgO, and BeO are little different from those in the literature.The compressive strength and bending strength of pure oxides at high temperatures are relatively low. The highest o_bend at high temperatures is possessed by specially pure zirconia, stabilized with MgO. Magnesia and beryllia in compressive strength at high temperatures exceed the other oxides.The highest spalling resistance is shown by beryllia ceramics. The combined addition to alumina of 1% TiO₂ and 5% ZrO₂ leads to a reduction in sintering temperature and an increase in thermal shock resistance. Ceramics based on specially pure zirconia stabilized with an optimum amount of CaO and MgO show a high thermal shock resistance.     

Effect of MgF2 addition on mechanical properties and thermal conductivity of silicon nitride ceramics

Dense silicon nitride (Si₃N₄) ceramics were prepared using Y₂O₃ and MgF₂ as sintering aids by spark plasma sintering (SPS) at 1650 °C for 5 min and post-sintering annealing at 1900 °C for 4 h. Effects of MgF₂ contents on densification, phase transformation, microstructure, mechanical properties, and thermal conductivity of the Si₃N₄ ceramics before and after heat treatment were investigated. Results indicated that the initial temperature of liquid phase was effectively decreased, whereas phase transformation was improved as increasing the content of MgF₂. For optimized mechanical properties and thermal conductivity of Si₃N₄, optimum value for MgF₂ content existed. Sample with 3 mol.% Y₂O₃ and 2 mol.% MgF₂ obtained optimum flexural strength, fracture toughness and thermal conductivity (857 MPa, 7.4 MPa m^1/2 and 76 W m⁻¹ K⁻¹, respectively). It was observed that excessive MgF₂ reduced the performance of the ceramic, which was caused by the presence of excessive volatiles.     

Effects of Y2O3–RE2O3 (RE = Sm,Gd, Lu) Additives on Electrical and Thermal Properties of Silicon Carbide Ceramics

In this study, we investigated the electrical and thermal properties of SiC ceramics with 2 vol% equimolar Y₂O₃–RE₂O₃ (RE = Sm, Gd, Lu) additives. The three SiC ceramics with 2 vol% equimolar Y₂O₃–RE₂O₃ additives showed electrical conductivities on the order of ~10³ (Ω·m)^?1, which is one order of magnitude higher than that of the SiC ceramics sintered with 2 vol% Y₂O₃ only. The increase in electrical conductivity is attributed to the growth of heavily nitrogen‐doped SiC grains during sintering and the confinement of oxide additives in the junction area. The thermal conductivities of the SiC ceramics were in the 176–198 W·(m·K)^?1 range at room temperature. The new additive systems, equimolar Y₂O₃–RE₂O₃, are beneficial for achieving both high electrical conductivity and high thermal conductivity in SiC ceramics.     

Preparation of closed-pore MgO-MgFe2O4 aggregates with low thermal conductivity and high mechanical properties

MgO-MgFe₂O₄ refractory aggregates with high closed porosity were fabricated using MgO agglomerates and Mg(OH)₂ with introducing Fe₂O₃ additive. The evolutions of pores and microstructure and their relationship with the properties of the specimens were studied. The addition of Fe₂O₃ obviously promoted the MgO grain growth and conversion of large open pores into small closed pores, attributing to the formation of cationic vacancies and intergranular MgFe₂O₄ bonding phase. Owing to the presence of closed pores and networks of intergranular MgFe₂O₄, both thermal insulation and strength were enhanced significantly. Besides, the formed closed pores and MgFe₂O₄ phase could accommodate thermal stress and induce transgranular fracture and crack deflection, therefore effectively improving the thermal shock resistance. The specimen with 15 wt% Fe₂O₃ showed a apparent/closed porosity of 0.7%/10.1%, median pore diameter of 4.37 µm, thermal conductivity of 9.3 W/(m·K) (500 °C), flexural strength of 143.5 MPa, and residual flexural strength of 24.1 MPa after thermal shock.