MMI阵列波导光栅复用/解复用器的研制

详细分析了基于自镜像效应的MMI DMUX器件的基本工作原理,在此基础上,在SOI材料上完成了对8信道MMI DMUX的具体设计.该器件的输入、输出单模波导采用Soref的大截面脊形光波导理论进行优化设计,最后获得了当输入、输出单模波导宽度为5μm,SIE多模波导宽度和长度分别为72μm和6313.4μm时,该器件对8信道波长的隔离度均在35dB以上,且理论传输损耗＜0.18dB.     

MMI型1.31/1.55 μm GaAs波分复用/解复用器的研制

利用多模波导的自镜像原理,分析设计了一种能直接与单模光纤相耦合的具有最小循环比的1.31/1.55 μm波长的GaAs/GaAlAs波分复用/解复用器。该器件的输入、输出单模波导和SIE多模波导采用离散谱折射率法进行优化设计,最后获得了当输入、输出单模波导宽为3 μm、SIE多模波导宽度和最佳耦合长度分别为18 μm和5 602.8 μm时,该器件对1.31 μm和1.55 μm两个波长的隔离度均在70 dB以上,且传输损耗小于0.1 dB。     

InP基4×4MMI合波器的设计与仿真

采用空气限制的InP基波导,利用其弯曲半径小的优点,设计了一款紧凑型4×4 MMI(多模干涉)合波器,整个器件的尺寸为3 890 μm×100 μm.在输入/输出波导与多模干涉区域之间引入了锥形波导,有效改善了MMI合波器的性能.并通过广角三维光束传输法对器件进行了模拟仿真,得到优化参量,从而实现了其结构的优化.     

聚合物双环谐振滤波器的研究

设计了一种基于多模干涉(MMI)耦合输入/输出结构的跑道型双微环串联谐振滤波器,并采用紫外光敏聚合物材料SU-8作波导芯层,聚合物CYTOP为下包层,在硅基底上完成了器件的制备.器件的波导端面尺寸为2 μm×1 μm,与设计值相符,扫描电镜显示所制备的器件波导侧壁陡直度较高.直波导传输损耗的测试结果表明,在1550 nm波长,直波导传输损耗约为2.0 dB/cm.测试并获得了多模干涉结构和器件的通光及输出光谱图\.测试结果表明,MMI结构在较宽的波长范围内实现了接近50∶50的功分比,微环谐振滤波器的通光性能良好,实现了滤波功能,器件的自由光谱区FSR实际值约为0.94 nm,与设计参数值很接近.研究结果表明采用聚合物SU-8制备小波导尺寸微环谐振器的器件简便可行.     

MMI型1.31／1.55umGaAs波分复用／解复用器的研制

利用多模波导的自镜像原理,分析设计了一种能直接与单模光纤相耦合的具有最小循环比的1031/1.55um波长的GaAs/G aAlAs波分复用／解复用器。该器件的输入、输出单模波导和SIE多模波导采用离散谱折射率法进行了优化设计,最后获得了当输入、输出单模波导宽为3um、SIE多模波导宽度和最佳耦合长度分别为18um和5602.8um时,该器件的1.31um和1.55um两个波长的隔离度均在70dB以上,且传输损耗小于0.1 dB.     

用于传感的聚合物微谐振环的研制

对一种用于传感的聚合物微谐振环进行了研制.器件为多模耦合器结构,作为微谐振环的输入/输出耦合结构.微谐振环采用跑道形结构.首先分析了器件的原理,给出了器件的优化设计参数.采用紫外光敏材料SU-8和CYTOP作为波导芯层和下包层材料,制作了上述结构的微谐振环器件,并进行了测试.扫描电镜的结果显示,所制备器件的整体形貌比较清晰,波导结构均匀光滑,侧壁陡直度较高.采用截断法测得单模直波导的传输损耗约为2.2 dBcm.对多模耦合器(MMI)结构和弯曲波导的测试表明,MMI结构在较宽的波长范围内实现了接近50:50的功分比,且损耗较低,而纯弯曲波导结构的通光性能良好.测量得到的器件谐振输出光谱表明,器件在主谐振峰处的插入损耗约为38dB,自由光谱区(FSR)约为1.87nm.过数据处理分析得到弯曲波导的传输损耗约为5.2 dB/cm.提出了进一步降低器件损耗、改善器件性能的措施.     

单模太赫兹量子级联激光器

为了获得窄线宽太赫兹光源,制作了基于表面金属光栅的单模太赫兹量子级联激光器。通过优化光栅结构,获得了具有较强耦合效率和较低损耗的光栅结构参数。波导结构采用半绝缘表面等离子体波导以便能获得较高的光输出功率。激光器单模激射波长为95μm。10 K时,器件最高单模输出功率达到了43 m W,单模抑制比为18 d B。单模器件工作温度超过70 K,在70 K时,仍然有5 m W的单模输出功率。这种输出性能良好的激光器有望作为太赫兹接收机的本振源。     

硅基槽波导级联多模干涉耦合器型偏振分束器

提出了一种基于硅基槽波导的级联多模干涉(MMI)耦合器型偏振分束器,由锥形及矩形结构MMI耦合器构成.级联结构使器件长度无需为两偏振模自镜像长度的公倍数,不仅能有效减小器件尺寸,而且提高设计灵活性.同时,利用槽波导的高双折射特性及MMI耦合器的锥形结构,可进一步缩短器件尺寸.分析结果表明,所提器件能够有效实现偏振束分离,两级MMI工作区总长度仅为42μm,准TE与准TM模的偏振消光比分别为29.8和31.4d B,1.55μm波长下的插入损耗分别为0.395和0.699 d B,偏振消光比大于20 d B时光带宽为43 nm,覆盖整个C波段.最后,详细分析了器件关键参数的制造误差对器件性能的影响.     

用择优腐蚀技术制作MMI型GaAs光功率分配器

通过对器件结构进行优化设计和择优腐蚀技术 ,用 H3 PO4 - H2 O2 - H2 O系腐蚀液制作了能直接与单模光纤阵列相耦合的 MMI型 Ga As1× 4光功率分配器 .最后用 1 .3 μm波长的He- Ne激光进行了测试 ,发现该器件基本实现了功率均分要求 ,功率离散度为 0 .1 55d B.     

1×3多模干涉型光功分器的研究

本文采用导模传输分析法,在GaAs/GaAlAs单异质结外延材料上设计了1×3MMI（多模干涉）型光功分器。根据所确定的器件结构参数,结合器件设计和制作过程中可能遇到的因素,详细分析了器件中自映像效应多模波导的宽度和长度、输入单模波导的宽度等结构参数对器件性能的影响。本文基于RSoft软件,对所设计的器件结构参量进行了仿真。模拟结果表明,所设计的器件实现了1×3光功分器功能,具有插入损耗低和均匀性好的特点。     

聚对苯撑苯并双(口恶)唑发光及其器件制备

采用光谱技术,研究了聚对苯撑苯并双(口恶)唑(PBO)溶液的光敏发光特性,并用相对法估算出溶液发光效率在50%范围.结合光谱技术、半导体电学和电化学等研究手段,具体研究了以PBO为发光层的单层电致发光器件,研究结果显示,电致发光与薄膜的光致发光有具有相同的发光中心,峰值位于510 nm左右.同时发现,由于存制备过程中不同处理条件使得不同厚度薄膜残留的掺杂物质浓度不同,从而引起薄膜的导电性的不同.使得器件的阈值场强随PBO厚度的减小而逐渐增加.     

系统级封装新型埋入式电源滤波结构的研究

在高密度小尺寸的系统级封装(SiP)中,对供电系统的完整性要求越来越高,多芯片共用一个电源网路所产生的电压抖动除了会影响到芯片的正常工作,还会通过供电网路干扰到临近电路和其他敏感电路,导致芯片误动作,以及信号完整性和其他电磁干扰问题.这种电压抖动所占频带相当宽,几百MHz到几个GHz的中频电源噪声普通方法很难去除.结合埋入式电容和电源分割方法的特点,提出一种新型高性能埋入式电源低通滤波结构直接替代电源/地平面.研究表明,在0.65～4GHz的频带内隔离深度可达-40～75 dB,电源阻抗均在0.25ohm以下,实现了宽频高隔离度的高性能滤波作用.分别用电磁场和广义传输线两种仿真器模拟,高频等效电路模型分析这种低通滤波器的工作原理以及结构对隔离性能的影响,并进行了实验验证.     

Emerging interconnects: a state-of-the-art review and emerging solutions

Aluminium was a primary material for interconnection in integrated circuits (ICs) since their inception. Later, copper was introduced as interconnect material which has better metallic conductivity and resistance to electromigration. As the aggressive technology scaling continues, the copper resistivity increased because of size effects, which causes increase in delay, power dissipation and electromigration. The need to reduce the resistor-capacitor??????? delay, dynamic power utilisation and the crosstalk commotion is as of now the fundamental main impetus behind the presentation of new materials. The purpose of this paper is to do a survey of interconnect material used in IC from introduction of ICs to till date. This paper studies and reviews new materials available for interconnect application which are optical interconnects, carbon nanotube (CNT), graphene nanoribbons (GNRs) and silicon nanowires which are alternatives to copper. While doing a survey of interconnect material, it is found that multiwalled CNTs, multilayer GNR and mixed CNT bundles are promising candidates and are ultimate choice that can strongly address the problems faced by copper but on integration basis copper would last for coming years.     

Arsenic deposition as a precursor layer on silicon (211) and (311) surfaces

We investigate the properties of arsenic (As) covered Si(211) and Si(311) surfaces by analyzing data from x-ray photoelectron spectroscopy (XPS) and low-energy electron diffraction (LEED) images. We then create a model using total surface energy calculations. It was found that both Si(211) and Si(311) had 0.68±0.08 surface As coverage. Si(211) had 0.28±0.04 Te coverage and Si(311) had 0.24±0.04 Te coverage. The Si(211) surface replaces the terrace and trench Si atoms with As for a lower surface energy, while the Si edge atoms form dimers. The Si(311) surface replaces all terrace atoms and adsorbs an As dimer every other edge site. These configurations imply an improvement in the mean migration path from the bare silicon surface by allowing the impinging atoms for the next epitaxial layer, tellurium (Te), to bind at every other pair of edge atoms, and not the step terrace sites. This would ensure a nonpolar, B-face growth.     

光子晶体微腔发光二极管

光子晶体微腔因其具有增强自发辐射、定向输出和单模工作的能力而受到广泛关注。介绍了光子晶体微腔发光二极管的基本原理、设计、特性、制作及其典型器件。     

Comparative study of maximum power point tracking techniques for hybrid renewable energy system

The power generation demand is increasing day-by-day throughout the world, therefore, the use of hybrid systems becomes a significant solution. The hybrid renewable energy system (HRES) is used for delivering power in various regions in order to overcome intermittence of wind and solar resources. Because of increasing environmental problems, for example, greenhouse gas emission and energy cost have interested novel research into substitute methods in favour of electrical power generation. Maximum Power Point Tracking (MPPT) control method is a vast deal of novel research used for enhancing the efficiency of HRES. The authors have revealed that the hybrid techniques i.e. Global MPPT, fuzzy-neuro systems, Adaptive Neuro-Fuzzy Inference System (ANFIS), Perturbed and Observe (P&O) + Adaptive Neural Network (ANN) etc. can provide best results as compared to other MPPT control methods. This paper offering a state of art review of MPPT control techniques for HRES.     

用于单光子TOF测量的时间-幅度变换器

基于新型共源共栅电流源的积分方法,设计了一种用于单光子飞行时间(TOF)测量的时间-幅度变换器(TAC)。该方法有效简化了TAC电路结构,减小了TAC占用面积,显著提高了TOF的满量程范围(FSR)。采用0.18 μm标准CMOS工艺设计。集成TAC的单光子探测器像素单元的填充因子可达到26.8%。后仿真结果表明,该TAC在120 ns的FSR内具有230 ps的定时分辨率,微分非线性(DNL)低于0.05 LSB,积分非线性(INL)低于1.1 LSB。蒙特卡洛仿真表明,512个TAC像素间的不均匀性低于0.5 %。该TAC非常适用于高密度时间相关的单光子计数(TCSPC)探测器阵列。     

超宽带脉冲信号的光学生成方法研究

近年来超宽带(UWB)通信技术迅猛发展,在测量、雷达技术、民用和军事无线通信中有着重要的应用,UWB-over-fiber技术已经成为目前研究的热点,其中就包括UWB脉冲信号的产生方法。区别于传统的电子学方法,光子学产生方法不受电子瓶颈制约,可以实现很高的带宽,并且具有抗电磁干扰、重量轻、结构紧凑的优点。通过对比国内外本领域研究成果,讨论及总结了以下三种原理的UWB脉冲信号的光学生成方法:1)相位调制-强度调制转换(PM-IM);2)半导体光放大器(SOA)的非线性效应;3)频谱塑形和色散所致频域-时域映射,然后对各种方案进行了对比分析。     

Joint estimation of TOA and DOA in IR-UWB system using a successive propagator method

Impulse radio ultra-wideband (IR-UWB) ranging and positioning require accurate estimation of time-of-arrival (TOA) and direction-of-arrival (DOA). With receiver of two antennas, both of the TOA and DOA parameters can be estimated via two-dimensional (2D) propagator method (PM), in which the 2D spectral peak searching, however, renders much higher computational complexity. This paper proposes a successive PM algorithm for joint TOA and DOA estimation in IR-UWB system to avoid 2D spectral peak searching. The proposed algorithm firstly gets the initial TOA estimates in the two antennas from the propagation matrix, then utilises successively one-dimensional (1D) local searches to achieve the estimation of TOAs in the two antennas, and finally obtains the DOA estimates via the difference in the TOAs between the two antennas. The proposed algorithm, which only requires 1D local searches, can avoid the high computational cost in 2D-PM algorithm. Furthermore, the proposed algorithm can obtain automatically paired parameters and has better joint TOA and DOA estimation performance than conventional PM algorithm, estimation of signal parameters via rotational invariance techniques algorithm and matrix pencil algorithm. Meanwhile, it has very close parameter estimation to that of 2D-PM algorithm. We have also derived the mean square error of TOA and DOA estimation of the proposed algorithm and the Cramer-Rao bound of TOA and DOA estimation in this paper. The simulation results verify the usefulness of the proposed algorithm.     

多孔硅发光机制的分析

从量子力学的基本理论出发讨论了量子限制效应，推导出多孔硅有效禁带宽度增量并用量子限制效应和表面态及其物质在发光中作用的理论解释了ＰＳ光致发光的实验现象。