AM60镁合金与铜合金及铝合金偶接后的大气腐蚀行为

研究了AM60铸造镁合金与H62铜合金、LY12铝合金组成的电偶对在北京地区室外曝晒3个月和6个月后的大气电偶腐蚀行为及规律.结果表明:镁合金始终是电偶对中的阳极,当其与H62铜合金和LY12铝合金偶接时,其腐蚀速率增加1～7倍;镁合金与H62铜合金偶合后,其大气电偶腐蚀效应大于其与LY12铝合金组成的电偶对的大气电偶腐蚀效应;在6个月的实验周期内,随着曝晒时间的延长,镁合金在北京地区大气环境中的电偶腐蚀效应呈上升趋势;试样表面润湿时间短是造成AM60镁合金在北京曝晒第一个实验周期(2003.12～2004.2)的电偶腐蚀低于第二个由实验周期(2004.3～2004.5)的主要原因;北京地区高自然降尘量对镁合金电偶腐蚀将起到加速的作用.     

镁合金在大气环境中电偶腐蚀行为及规律的研究

在北京大气环境下，研究AM60镁合金和不同金属材料（碳钢、不锈钢、黄铜和铝合金）偶接的电偶腐蚀行为规律。研究表明，镁合金作为阳极发生不同程度的电偶腐蚀，通过1a的北京大气环境下的暴露试验后，AM60镁合金的电偶腐蚀效应由强到弱的顺序为：碳钢、黄铜、不锈钢和铝合金，其中镁合金与LY12铝合金偶接的电偶腐蚀效应最小。通过与其它地区室外暴晒的镁合金电偶腐蚀效应的对比，表明环境因素影响着镁合金的电偶腐蚀效应。同时阴极材料、试验时间、试样尺寸（偶接面积）和试验环境都会对镁合金电偶腐蚀效应产生影响。经1a曝晒的AM60镁合金形成了具有保护性的腐蚀产物层阻碍了腐蚀发展。北京地区高自然降尘量导致金属表面湿润时间加大，从而加速了AM60镁合金的电偶腐蚀。采用XRD方法分析表面的腐蚀产物，用金相显微镜和扫描电镜（SEM）观察试样腐蚀后的表面形貌特征和腐蚀产物的结构，并用与之相连的能谱仪分析腐蚀产物中的元素组成。     

镁合金在大气环境中电偶腐蚀行为及规律的研究

研究了北京大气环境下，AM50镁合金作为阳极发生不同程度的电偶腐蚀行为规律。结果表明其中镁合金与LY12铝合金偶接的电偶腐蚀效应最小。通过与其他地区室外暴晒的镁合金电偶腐蚀效应对比，表明环境因素，尤其是试验开始初期阶段的大气环境状况对于镁合金初期电偶腐蚀行为有着重要的影响。同时阴极材料、试验时间、试样尺寸（偶接面积）和试验环境都会对镁合金电偶腐蚀效应产生影响。采用XRD分析表面的腐蚀产物，用金相显微镜和扫描电镜（SEM）观察试样腐蚀后的表面形貌特征和腐蚀产物的结构，并用与之相连的能谱仪分析腐蚀产物中的元素组成。     

模拟大气环境中加速镁合金电偶腐蚀的研究

研究了压铸镁合金AZ91D分别与黄铜、铝合金、316L不锈钢和A3钢组成的电偶在模拟的大气环境即盐雾和湿热的加速腐蚀试验中的电偶腐蚀行为及规律.结果表明:在此气相环境中，镁合金腐蚀倾向显著;多种因素可以加速镁合金的电偶腐蚀；盐雾实验中，盐的浓度、大阴极小阳极的面积比以及阴极材料相对于镁阳极的尺寸是加速镁合金电偶腐蚀的重要因素.      

AZ91D镁合金电偶腐蚀的研究

在自来水和3.5%NaCl溶液中测试了铸造AZ91D镁合金与铝合金、锌合金、Q235碳钢和Cu偶合后的电偶腐蚀行为,研究了腐蚀环境、偶接材料和阴阳极面积比(CAAR)对铸造AZ91D镁合金电偶腐蚀行为的影响。在电偶腐蚀过程中测量溶液的pH值以及电偶腐蚀电流;用失重法计算了铸造AZ91D镁合金的电偶腐蚀速率,利用SEM观察了AZ91D镁合金的腐蚀形貌,并对腐蚀产物进行XRD分析。结果表明,AZ91D镁合金在电偶腐蚀过程中会使溶液的pH值升高,并伴有以Mg(OH)₂为主的腐蚀产物的生成;溶液中Cl^-的存在会加速AZ91D镁合金的电偶腐蚀速率;低氢过电位金属Q235碳钢和Cu对AZ91D镁合金的电偶腐蚀加速效果明显高于中氢过电位金属铝合金和锌合金,偶接材料的极化性能对AZ91D镁合金的电偶腐蚀速率有较大影响。同时,大的阴阳极面积比会加速AZ91D镁合金的电偶腐蚀速率,且AZ91D镁合金的电偶腐蚀电流随阴阳极面积比的增大而呈线性增长趋势。     

AZ91D镁合金电偶腐蚀的扫描Kelvin探针研究

利用扫描Kelvin探针技术(SKP)研究AZ91D镁合金与316L不锈钢偶接件在盐雾试验中电偶腐蚀规律。通过在中性盐雾试验不同周期的表面腐蚀形貌的观察和伏打电位分布图的测量结果分析表明,AZ91D镁合金电偶腐蚀效应与偶接阴阳极的伏打电位差密切相关,AZ91D镁合金与316L不锈钢偶接件存在较大的电位差(约为–1.28V),其电偶腐蚀效应非常显著。在盐雾试验初始阶段,腐蚀主要发生在偶接界面AZ91D镁合金一侧,该腐蚀区域的伏打电位增加幅度较大,而316L不锈钢受到保护没有发生明显腐蚀。随着盐雾试验时间的延长,AZ91D镁合金腐蚀加快,腐蚀产物覆盖区域不断扩大,24h盐雾试验后,偶接件的平均伏打单位差由原始的–1.29V增加到–1.53V,AZ91D镁合金的电偶腐蚀效应加大。由于AZ91D镁合金在盐雾中生成的腐蚀产物对基体具有一定的保护作用,当腐蚀产物不断增加并覆盖表面,偶接件的电位差减小导致AZ91D镁合金的电偶腐蚀效应降低。     

AZ91D镁合金在北京地区的大气腐蚀行为研究

利用室外大气暴露试验，研究了AZ91D镁合金在北京地区的平均大气腐蚀速率，并与相同条件下A3钢的大气腐蚀情况进行了对比．采用扫描电镜(SEM)、X-射线衍射(XRD)、X射线能谱(EDS)以及红外光谱(IR)等多种现代表面分析技术对腐蚀产物的形貌、组成、结构等进行分析，与A3钢相比，AZ91D镁合金具有良好的耐大气腐蚀性能，具有局部腐蚀的特征。     

AZ91D镁合金在临汾工业大气中的腐蚀行为

采用室外大气暴露试验,测定了AZ91D镁合金、防锈铝在工业大气环境中的腐蚀率,AZ91D镁合金在干燥污染的工业大气中较耐蚀.通过扫描电镜、X衍射及能谱检测分析表明:AZ91D镁合金腐蚀产物由Al、Mg的氧化物和硫化物组成,Al2O3、MgCO3 对 AZ91D镁合金形成保护.     

具有阴极电泳涂层AM50镁合金与钢接触电偶腐蚀

研究了AM50裸镁合金及在裸镁合金上进行阴极电泳处理、硅烷预处理再阴极电泳处理3种不同样件与Q235钢螺栓连接在5%NaC1水溶液中浸泡的腐蚀规律,仔细观察对比3种不同表面状态的镁合金在不同时间浸泡后的表面腐蚀情况,测定各自的腐蚀速率,对腐蚀后的区域进行微观分析,并用腐蚀模型对其腐蚀的行为规律进行了解释.结果表明:镁合金可以通过阴极电泳处理获得耐蚀防护涂层,硅烷预处理可以进一步提高电泳膜层与基体的附着力,从而大大提高镁合金与钢螺栓接触的耐电偶腐蚀性;AM50镁合金与Q235钢螺栓接触电偶腐蚀的影响区面积不随腐蚀时间的延长而增大,其电偶腐蚀速度沿纵深方向(与螺栓接触方向)比横向的均匀腐蚀速度快.     

AZ80镁合金与异种合金的电偶腐蚀研究

在3.5%NaCl溶液中将AZ80镁合金与石墨、铝合金、锌合金、铜合金、Q235碳钢偶合进行电偶腐蚀。在电偶腐蚀过程中测量溶液pH值及电偶电流,用失重法计算AZ80镁合金的电偶腐蚀速率,并用XRD分析腐蚀产物成分。结果表明:3.5%NaCl溶液的pH升高并在10.5左右达到平稳且腐蚀产物以Mg(OH)2为主;电偶腐蚀加快AZ80镁合金腐蚀;电偶对阴阳面积比越大,AZ80镁合金电偶腐蚀越严重。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

THERMODYNAMICS STUDY ON THE DECOMPOSITION OF CHROMITE WITH KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

INFLUENCE OF HEAT TREATMENT ON DAMPING BEHAVIOUR OF THE MAGNESIUM WROUGHT ALLOY AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

An Easy Way to Quantify the Adhesion Energy of Nanostructured Cu/X(X=Cr,Ta,Mo,Nb,Zr) Multilayer Films Adherent to Polyimide Substrates

An approach based on film buckling under simple uniaxial tensile testing was utilized in this paper to quantitatively estimate the interfacial energy of the nanostructured multilayer films(NMFs) adherent to flexible substrates. The interfacial energies of polyimide-supported NMFs are determined to be *5.0 J/m2 for Cu/Cr, *4.1 J/m2 for Cu/Ta,*2.8 J/m2 for Cu/Mo, *1.1 J/m2 for Cu/Nb, and *1.2 J/m2 for Cu/Zr NMFs. Furthermore, a linear relationship between the adhesion energy and the interfacial shear strength is clearly demonstrated for the Cu-based NMFs, which is highly indicative of the applicability and reliability of the modified models.     

High-Speed Friction Stir Welding of SiC_p/Al–Mg–Si–Cu Composite

A 17 vol% SiCp/Al–Mg–Si–Cu composite plate with a thickness of 3 mm was successfully friction stir welded(FSWed) at a very high welding speed of 2000 mm/min for the first time. Microstructural observation indicated that the coarsening of the precipitates was greatly inhibited in the heat-affected zone of the FSW joint at high welding speed, due to the significantly reduced peak temperature and duration at high temperature. Therefore, prominent enhancement of the hardness was achieved at the lowest hardness zone of the FSW joint at this high welding speed, which was similar to that of the nugget zone. Furthermore, the ultimate tensile strength of the joint was as high as 369 MPa, which was much higher than that obtained at low welding speed of 100 mm/min(298 MPa). This study provides an effective method to weld aluminum matrix composite with superior quality and high welding efficiency.