Pr-TiO_2光催化剂的制备与性能研究

采用溶胶-凝胶法制备了稀土元素Pr掺杂的纳米TiO2光催化剂(Pr-TiO2)。通过XRD、FT-IR、UV-Vis、TEM等对Pr-TiO2样品进行了表征和分析,并以亚甲基蓝(MB)作为目标降解物,考察了不同热处理温度及不同掺杂量的Pr-TiO2对MB的光催化降解效果。结果表明,Pr掺杂纳米TiO2的晶型为锐钛矿相和金红石相的混晶相,Pr的掺入提高了TiO2光催化活性。当热处理温度为500℃,在pH值为2.5,Pr掺杂量为n(Pr):n(TiO2)=1:300的条件下制备的光催化剂的催化活性显著高于DegussaP25。     

Ce-TiO2光催化剂的制备与性能研究

采用溶胶-凝胶法制备了稀土Ce离子掺杂的纳米TiO2光催化剂(Ce-TiO2),通过XRD、FT-IR、UV-Vis、PL、Nano-sizer纳米粒度分析仪等对Ce-TiO2样品进行了表征和分析,并以亚甲基蓝(MB)作为目标降解物,考察了不同掺杂浓度及经不同温度热处理后的Ce-TiO2样品对MB的光催化降解效果,结果表明所制备样品的晶型均为锐钛矿相和金红石相的混晶相,Ce离子的掺杂拓展了TiO2在可见光区的光谱响应范围,提高了TiO2光催化活性。当pH值为1.5,Ce的掺杂量为n(Ce)∶n(TiO2)=1∶300,热处理温度为600℃条件下制备的样品其催化活性显著高于Degussa P25。     

不同介质中水热合成纳米TiO2粉体及其光催化性能研究

以钛酸四丁酯为原料,采用水热法分别以蒸馏水、有机小分子化合物(正丁醇、丙二酸和乙二胺水溶液)和无机酸(HNO3、H2SO4和HCl)为介质合成了TiO2纳米粉体.通过XRD和TEM对所得TiO2粉体进行了表征,研究不同介质对所得TiO2粉体的晶相组成、颗粒尺寸及形貌的影响.结果表明:以蒸馏水为介质时所得锐钛矿TiO2的颗粒尺寸分布不均匀;有机化合物抑制锐钛矿型TiO2各向异性生长趋势的能力为:正丁醇＞丙二酸＞乙二胺;相同实验条件下,HCl、H2SO4及HNO3体系中分别获得金红石、锐钛矿及锐钛矿和金红石混晶TiO2.光催化降解甲基橙的研究表明,锐钛矿和金红石混晶TiO2的光催化活性要高于纯锐钛矿结构;纯金红石型TiO2的光催化活性最差.     

Sm3+和Gd3+共掺杂TiO2粉体的制备和性能表征

采用溶胶-凝胶法制备了纯TiO2,1%Sm3+或2%Gd3+单掺杂和1%Sm3+/2%Gd3+共掺杂TiO2复合粉体,采用XRD和SEM/EDAX等技术进行表征。以对亚甲基蓝的光催化降解为目标反应,评价了TiO2复合粉体的光催化活性,探讨了Sm3+/Gd3+共掺杂、亚甲基蓝初始浓度和粉体投加量对TiO2粉体光催化活性的影响机制。结果表明,Sm3+/Gd3+共掺杂可以显著提高TiO2粉体的光催化活性;Sm3+/Gd3+共掺杂在TiO2粉体中产生协同作用,抑制了TiO2由锐钛矿相向金红石相转变,使TiO2粒径尺寸减小,增大了TiO2的晶格畸变。当亚甲基蓝初始浓度为4mg/L和粉体投加量为2g/L时,TiO2复合粉体的光催化活性最高,对亚甲基蓝光催化降解率达99.71%;降解亚甲基蓝反应符合Langmuir-Hinshelwood动力学方程。     

溶胶-凝胶法制备TiO2粉体及其光催化性能研究

以钛酸丁酯为前驱物,无水乙醇为溶剂,采用溶胶-凝胶法制备了TiO2粉体,并采用紫外分光光度计、XRD等表征手段对TiO2的粒度、晶型结构进行了表征,分析了煅烧温度、TiO2晶型比例、溶液初始pH值等因素对TiO2结构性能及光催化活性的影响.结果表明:TiO2的锐钛矿晶型与金红石晶型的转相温度为700 ℃左右;采用溶胶-凝胶法制备TiO2时,控制溶液的pH值为4,煅烧温度为600 ℃,所得产物晶型全部为锐钛矿;当无水乙醇与钛酸丁酯的体积比为10:1时,产物的粒径为617 nm;且当配制溶液pH值为4,煅烧温度为600℃条件下,煅烧时间为40~60 min时,所制备TiO2的光催化效果较好,降解率较高;当光催化体系的pH值为9、以质量浓度为10 mg/L的亚甲基兰溶液浸泡2 h,TiO2的用量为0.25 g/L时,产物的降解率高达95.3%.     

纳米二氧化钛光催化活性影响因素的研究

以苯酚为模拟污染物,考察了不同晶型、溶液初始pH值、反应物初始浓度、氧气的协同作用对TiO2悬浮体系光催化活性的影响;并将TiO2负载到活性炭纤维上,制备了固定体系的TiO2/ACF复合催化剂.结果表明,具有混晶结构的P25降解速率比纯锐钛矿TiO2快;溶液pH=6及苯酚初始浓度为150 mg/L时,降解速度最快;通入氧气,可以提高催化剂活性;光催化降解苯酚表明,TiO2/ACF复合催化剂具有较好的光催化活性.     

铁掺杂TiO2光催化剂的制备及光催化性能

采用溶胶-凝胶法制备铁掺杂纳米TiO2光催化剂。通过XRD、FT-IR、UV-Vis、PL等对Fe-TiO2样品进行表征和分析,并以亚甲基蓝（MB）作为目标降解物,考察经不同热处理温度及不同掺铁量Fe-TiO2样品对MB的降解效果。结果表明所制备的Fe-TiO2样品的晶型为锐钛矿相与金红石相的混晶相,铁掺杂抑制了晶粒的生长和晶型的转变,样品的吸收阈值波长向可见光红移约68nm,提高了TiO2的光催化活性。在普通日光灯下,经500℃热处理、掺铁量与TiO2摩尔比为1∶200条件下制备的催化剂其光催化活性明显高于Degussa P25。     

Yb-TiO2光催化剂的制备及性能研究

采用溶胶-凝胶法制备了稀土Yb掺杂纳米TiO2光催化剂(Yb-TiO2),采用XRD、UV-Vis、FT-IR等方法对其进行表征和分析,并以亚甲基蓝(MB)作为目标降解物,考察了热处理温度以及Yb掺杂量对样品性能的影响。实验结果表明,Yb掺杂样品均为金红石相和锐钛矿相的混晶相,Yb的掺入拓展了TiO2对可见光的吸收范围,有效地抑制了光生电子-空穴对的复合,提高了TiO2的光催化活性。当pH值=2.5、n(Yb)∶n(Ti)=0.005、热处理温度为650℃时,制备的样品其光催化活性明显优于Degussa P25。     

太阳光下Cr~(3+)掺杂TiO_2复合微粒光催化性能研究

利用酸催化的溶胶一凝胶法成功地合成了一系列不同CP3+掺杂量(x=0.01%～10%)的TiO2复合光催化剂(Cd3+/TiO2).在太阳光条件下,以亚甲基蓝溶液的光催化降解对复合材料的光催化性能进行了表征,并考察了催化剂投加量、Cr3+掺杂量和溶液pH值等因素对光催化降解反应的影响.结果表明,亚甲基蓝溶液在复合微粒上的光催化降解反应遵循Langmuir-Hinshelwood动力学模型,在催化剂投加量为lg/L、Cr3+掺入量为0.3%和pH=7时,Cr3+/TiO2复合微粒光催化活性达最佳,测得表观反应速率常数 K为7.27×10-3 rag(L·min)-1,t1/2为95min,反应4h后亚甲基蓝的降解率可达79%,与纯的TiO2相比较,反应速率提高了2倍,降解率提高了20%.中性或碱性条件下有利于亚甲基蓝溶液的光催化降解.     

不同晶型纳米TiO2的溶剂热合成及其光催化活性研究

采用不同的醇溶剂,以六亚甲基四胺为沉淀剂,以TICl3为前驱体,通过溶剂热的方法控制合成出纳米级的锐钛矿型、金红石型和板钛矿型的二氧化钛.通过XRD、TEM、UV-Vis光谱和XPS能谱对其进行了表征,研究了醇的种类、六亚甲基四胺的量对二氧化钛相组成及光催化性能的影响.结果发现,以甲醇为溶剂,酸性条件有利于生成锐钛矿相,碱性条件有利于生成金红石相和板钛矿相.溶剂热条件下可以得到氮掺杂的TiO2-xNx.光催化降解甲基橙活性结果表明锐钛矿和板钛矿混晶具有最好的光催化活性.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Synthesis of Alumina-Zirconia Nanocomposites by Solgel Process

Al₂O₃-ZrO₂ nanocomposites were developed starting with the solgel process. Composite alumina-zirconia nanopowders were synthesized from metallorganic precursors (Aluminium secondary butoxide and zirconium Iso propoxide) using the solgel process. The parameters affecting the synthesis—solvent, concentration of precursor, R/H ratio (i.e., dilution of water in solvent)—were varied as also the temperature and pH. BET and TEM were used to measure nanosize. Diffuse reflectance spectroscopy and also qualitative optical absorption led to identical particle size estimate. The variation of process parameters was used to study the effect and interdependence of process parameters. Artificial Neural Networks was used to rigorously analyze the process. Although this led to confirmation of interdependence of parameters, the presence of a single overwhelming solvent variable was also established. Then the optimal process was used to synthesize more nanopowder. To produce bulk nanocomposite the nanopowders were sintered by varying the temperature and time period. The sintered lithoids were probed with a vickers hardness tester to measure elastic modulus, hardness, and fracture toughness. The results showed high elastic modulus, modest hardness, and very high fracture toughness.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Friction Stir Processing Strategies for Uniform Distribution of Reinforcement in a Surface Composite

Friction stir processing (FSP) is an important technique for preparing surface composites. Fabricating defect-free surface composites with uniform particle distribution by FSP is a challenging task. In this study, silicon carbide particles reinforced AA5083 alloy surface composites was fabricated using different FSP strategies including variation in process parameters, dual-tool processing and tool offset overlapping. Material flow of the processed material with reinforcement particles demonstrated that the distribution of particles was influenced by the stirring action of the probe as well as the extrusion of the plasticized material due to the movement of the tool. Process parameters, particularly rotational speed, showed a dominant influence on the distribution of silicon carbide particles.