A technical note on application of internally finned tubes in solar parabolic trough absorber pipes

The heterogeneous incoming heat flux in solar parabolic trough absorber tubes generates huge temperature difference in each pipe section. Helical internal fins can reduce this effect, homogenising the temperature profile and reducing thermal stress with the drawback of increasing pressure drop. Another effect is the decreasing of the outer surface temperature and thermal losses, improving the thermal efficiency of the collector. The application of internal finned tubes for the design of parabolic trough collectors is analysed with computational fluid dynamics tools. Our numerical approach has been qualified with the computational estimation of reported experimental data regarding phenomena involved in finned tube applications and solar irradiation of parabolic trough collector. The application of finned tubes to the design of parabolic trough collectors must take into account issues as the pressure losses, thermal losses and thermo-mechanical stress, and thermal fatigue. Our analysis shows an improvement potential in parabolic trough solar plants efficiency by the application of internal finned tubes.     

Analysis of internal helically finned tubes for parabolic trough design by CFD tools

This paper has analysed the effect of the utilization of internal finned tubes for the design of parabolic trough collectors with computational fluid dynamics tools. Our numerical approach has been qualified with the computational estimation of reported experimental data regarding phenomena involved in finned tube applications and solar irradiation of parabolic trough collector. The application of finned tubes to the design of parabolic trough collectors must take into account features as the pressure losses, thermal losses and thermo-mechanical stress and thermal fatigue. Our analysis shows an improvement potential in parabolic trough solar plants efficiency by the application of internal finned tubes.     

多排槽式反射镜风压分布及干扰研究

为研究多排槽式反射镜不同位置处的风荷载特性及其互相干扰,对单个反射镜及多排反射镜进行缩尺为1/40的刚性模型测压试验,试验变量为测压模型的风攻角、风向角以及其在群镜中的位置。首先测得各工况下镜面的风压分布数据,绘制镜面风压系数等值线图和反射镜力系数变化曲线,然后分析了反射镜互相干扰对镜面风荷载的影响。研究表明：中间列首排反射镜所受风荷载最大,其阻力系数是单镜的2倍,中间列其余排反射镜阻力系数为单镜的30%~70%;边缘列首排反射镜阻力系数为单镜的1.88倍,其余各排在单镜的1.20倍以上;建议将镜场分为4类区域分别进行结构设计。     

Performance of Cylindrical Parabolic Collector with Automated Tracking System

Parabolic solar collector collects the radiant energy emitted from the sun and focuses it at a point. Parabolic trough collectors are the low cost implementation of concentrated solar power technology that focuses incident sun light on to a tube filled with a heat transfer fluid. However, the basic problem with the cylindrical parabolic collector without tracking was the solar collector does not move with the orientation of sun. Development of automatic tracking system for cylindrical parabolic collectors will increase solar collection as well as efficiency of devices. The main aim of this paper is to design, fabricate and analyze the performance of parabolic collector with automated tracking system. The automated tracking mechanism is used to receive the maximum possible energy of solar radiation as it tracks the path of sun. The performance of the parabolic trough collector is experimentally investigated with the water circulated as heat transfer fluid. The collector efficiency will be noted.     

Analytic modeling of a solar power plant with parabolic linear collectors

An analytic model for a solar thermal electric generating system with parabolic trough collectors was developed. The energy conversion of solar radiation into thermal power along the absorber tube of the parabolic collector is studied, taking into consideration the non-linearity of heat losses and its dependence on the local temperature. The coupling between the collector and the thermodynamic cycle is made up of three heat exchangers, yielding the characteristic temperatures of the cycle. The conventional Rankine cycle is treated as an endo-reversible Carnot cycle, whereby the mechanical and electric power is calculated. For comparison, we refer to the Solar Electric Generating System VI (SEGS VI), installed in the Mojave desert-CA, whose solar field is composed by LS2 parabolic trough collectors. We simulated the efficiency curves of collectors LS2 with evacuated and non-evacuated absorbers and compared with experimental results. A second simulation was carried out to estimate the optimum quantity of non-evacuated LS2 collectors in series in a collectors’ row, when friction losses along the absorber tubes are considered. Also, the performance of a 30 (MWe) power plant, composed of 50 rows with 16 LS2 collectors in series (total 800 collectors) was simulated. Three fields of different collectors were considered, the first field with evacuated absorbers, the second with non-evacuated absorbers and the third with bare absorbers. Finally, the output power of the plant is analyzed as a function of the evaporation temperature of the water-vapor fluid. A large maximum of the overall cycle efficiency is found for evaporation temperatures around 320 °C. Good agreement is obtained when comparing the results of this model with experimental data belonging to the Solar Electric Generating Systems (SEGS) installed in the Mojave desert. The analytic model developed combines simplicity, precision and flexibility, making it an attractive tool for simulation and design of solar power stations.     

A new TRNSYS component for parabolic trough collector simulation

This study describes and evaluates a new simulation component for parabolic trough collectors (PTCs). The new simulation component is implemented in the TRNSYS software environment by means of new Type that is suitable for integration into the calculation of a whole concentrating solar thermal plant, in order to evaluate the energy production of a PTC. The main advantage of the new Type is that is derived from experimental data available on efficiency Test Reports, according to the current European and International standards, rather than the theoretical approach considered in the existing parabolic trough component of TRNSYS library. The performance of the new Type has been validated with real experimental data obtained from the DISS solar test loop in Plataforma Solar de Almería, Spain. The paper describes the modelling approach, presents the comparison of simulation results with measurements taken at the DISS facility and evaluates the results.     

改进型微热管平板太阳能空气集热器性能分析

近年来,以空气作为换热介质的太阳能集热器越来越受到重视。本文以微热管阵列为核心传热元件,设计并搭建了改进型微热管平板太阳能空气集热器性能测试系统。通过实验研究了不同空气流量和不同进口温度对集热器集热性能的影响,获得相应参量对集热器的出口空气温度、集热效率和微热管阵列蒸发段温度的影响特性,分析对比了改进前后集热器的集热性能,得到了集热器效率的归一化曲线。实验结果表明,改进型微热管平板太阳能空气集热器在夏季240 m³/h空气流量时集热性能最佳,改进后的集热器相比原集热器在夏季的平均集热效率最高同比提升13.8%;在240 m³/h风量下的平均集热效率最高达到了74%,对应集热器的压降为9.2 Pa。     

Modelling of parabolic trough direct steam generation solar collectors

Solar electric generation systems (SEGS) currently in operation are based on parabolic trough solar collectors using synthetic oil heat transfer fluid in the collector loop to transfer thermal energy to a Rankine cycle turbine via a heat exchanger. To improve performance and reduce costs direct steam generation in the collector has been proposed. In this paper the efficiency of parabolic trough collectors is determined for operation with synthetic oil (current SEGS plants) and water (future proposal) as the working fluids. The thermal performance of a trough collector using Syltherm 800 oil as the working fluid has been measured at Sandia National Laboratory and is used in this study to develop a model of the thermal losses from the collector. The model is based on absorber wall temperature rather than fluid bulk temperature so it can be used to predict the performance of the collector with any working fluid. The effects of absorber emissivity and internal working fluid convection effects are evaluated. An efficiency equation for trough collectors is developed and used in a simulation model to evaluate the performance of direct steam generation collectors for different radiation conditions and different absorber tube sizes. Phase change in the direct steam generation collector is accounted for by separate analysis of the liquid, boiling and dry steam zones.     

槽式太阳能集热器热性能实验测试

针对天津市槽式太阳能集热系统性能测试平台,对不同太阳辐射强度、入口流体温度以及不同工质流量状况下集热效率和集热管压降变化规律进行实验测试,通过测试数据对槽式太阳能集热器热性能进行分析。试验结果表明:在天津地区槽式太阳能集热器集热效率可以达到66.1%;太阳辐射强度的增强,会提高集热效率,并且集热器进出口的压降会随之降低;在太阳辐射强度和导热油流量一定时入口流体温度存在最佳值;集热效率和集热器进出口的压降随着流量的增加而增大。     

An Experimental Investigation on the Effect of Ferrofluids on the Efficiency of Novel Parabolic Trough Solar Collector Under Laminar Flow Conditions

ABSTRACT

The paper is related to the use of magnetic nanofluids (ferrofluids) in a direct absorption solar parabolic trough collector, which enhances thermal efficiency compared to conventional solar collectors. By applying the right magnetic intensity and magnetic field direction, the thermal conductivity of the fluid increased higher than typical nanofluids. Moreover, the ferrofluids exhibit excellent optical properties. The external magnetic source is installed to alter the thermo-physical properties of the fluid, and the absorber tube does not have selective surface allowing ferrofluids to absorb the incoming solar irradiance directly. In this paper, an experimental investigation of the performance of small scale direct absorption solar collector using ferrofluids as an absorber was conducted. Nanoparticle concentrations of 0.05 vol% at the operational temperatures between 19°C and 40°C were used in the current study. The results show that using ferrofluids as a heat transfer fluid increases the efficiency of solar collectors. In the presence of the external magnetic field, the solar collector efficiency increases to the maximum, 25% higher than the conventional parabolic trough. At higher temperatures, the ferrofluids show much better efficiency than conventional heat transfer fluid. The study indicated that nanofluids, even of low-content, have good absorption of solar radiation, and can improve the outlet temperatures and system efficiencies. The study shows the potential of using ferrofluids in the direct absorption solar collector.     

抛物槽式集热器热效率研究

介绍槽式集热器的结构及其工作过程,对集热器进行热性能分析,研究已有集热器热力学模型,并对其进行优化,利用该模型计算各个部位的热损失大小以及集热器热效率,分析得出影响集热器热效率的主要因素,定量分析这些因素对集热器效率的影响趋势,并解释其原因。     

Effect of using nanofluids on efficiency of parabolic trough collectors in solar thermal electric power plants

In this paper, forced convection heat transfer nanofluid flow inside the receiver tube of solar parabolic trough collector is numerically simulated. Computational Fluid Dynamics (CFD) simulations are carried out to study the influence of using nanofluid as heat transfer fluid on thermal efficiency of the solar system. The three-dimensional steady, turbulent flow and heat transfer governing equations are solved using Finite Volume Method (FVM) with the SIMPLEC algorithm. The results show that the numerical simulation are in good agreement with the experimental data. Also, the effect of various nanoparticle volume fraction on thermal and hydrodynamic characteristics of the solar parabolic collector is discussed in details. The results indicate that, using of nanofluid instead of base fluid as a working fluid leads to enhanced heat transfer performance. Furthermore, the results reveal that by increasing of the nanoparticle volume fraction, the average Nusselt number increases.     

Numerical simulation of parabolic trough solar collector: Improvement using counter flow concentric circular heat exchangers

Detailed numerical simulations of thermal and fluid-dynamic behavior of a single-pass and double-pass solar parabolic trough collector are carried out. The governing equations inside the receiver tube, together with the energy equation in the tube walls and cover wall and the thermal analysis in the solar concentrator were solved iteratively in a segregated manner. The single-pass solar device numerical model has been carefully validated with experimental data obtained by Sandia National Laboratories. The effects of recycle at the ends on the heat transfer are studied numerically shown that the double-pass can enhance the thermal efficiency compared with the single-pass.     

The potential of solar industrial process heat applications

The temperature requirements of solar industrial process heat applications range from 60 °C to 260 °C. The characteristics of medium to medium-high temperature solar collectors are given and an overview of efficiency and cost of existing technologies is presented. Five collector types have been considered in this study varying from the simple stationary flat-plate to movable parabolic trough ones. Based on TRNSYS simulations, an estimation of the system efficiency of solar process heat plants operating in the Mediterranean climate are given for the different collector technologies. The annual energy gains of such systems are from 550 to 1100 kWh/m² a. The resulting energy costs obtained for solar heat are from 0.015 to 0.028 C£/kWh depending on the collector type applied. The viabilities of the systems depend on their initial cost and the fuel price. None of these costs however is stable but change continuously depending on international market trends and oil production rates. The costs will turn out to be more favourable when the solar collectors become cheaper and subsidisation of fuel is removed. Therefore the optimisation procedure suggested in this paper should be followed in order to select the most appropriate system in each case.     

Saturated steam process with direct steam generating parabolic troughs

The direct steam generation (DSG) in parabolic trough collectors is an attractive option regarding the economic improvement of parabolic trough technology for solar thermal electricity generation in the multi Megawatt range. The European DISS project has proven the feasibility of the direct steam generation under real solar conditions in more than 4000 operation hours. Within the European R&D project INDITEP the detailed engineering for a pre-commercial DSG solar thermal power plant with an electrical power of 5 MW is being performed. This small capacity was chosen to minimise the risk for potential investors.In regards to DSG solar thermal power plants, only steam cycles using superheated steam have been investigated so far. The paper will investigate the advantages, disadvantages, and design considerations of a steam cycle operated with saturated steam for the first time. For near term applications, saturated steam operated DSG plants might be an interesting alternative for power generation in the small capacity range due to some specific advantages:

• Simple set up of the collector field.

• Proven safe collector field operation.

• Higher thermal efficiency in the collector field.

Analysis of wind flow around a parabolic collector (1) fluid flow

Applications of parabolic collectors for solar heating and solar thermal power plant increased in the recent years. Most of the solar power plants installed with parabolic collectors are on flat terrain and they may be subjected to some environmental problems. One of problems for large parabolic collector is their stability to track the sun with respect to time very accurately. Any small off tracking as well as the collector structure stability will be affected by strong wind blowing for the regions where the wind velocity is high.In the present study, a two-dimensional numerical simulation of turbulent flow around a parabolic trough collector of the 250 kW solar power plants in Shiraz, Iran is performed taking into account the effects of variation of collector angle of attack, wind velocity and its distribution with respect to height from the ground.Computation is carried for wind velocity of 2.5, 5, 10, and 15 m/s and collector angles of 90°, 60°, 30°, 0°, −30°, −60°, and −90° with respect to wind directions. Various recirculation regions on the leeward and forward sides of the collector are observed, and both pressure field around the collector and total force on the collector are determined for each condition. The effect of absorber tube on the flow field was found negligible, while the effect of the gap between the two sections of parabola at midsection and the gap between the collector and ground were found considerable on both flow field and pressure distribution around the collector.     

Field measurements of boundary layer wind characteristics and wind loads of a parabolic trough solar collector

The focus of the current study is the wind loads on a 11.92 m section of parabolic trough collector with an aperture of 5.76 m, located in Beijing, PR China. This paper presents selected results of full-scale field measurements of wind loads and wind pressure on the solar collector. The field data such as wind speed, wind direction and wind pressures are simultaneously measured from the solar collector. The measured data are analyzed to obtain the information on boundary layer wind characteristics, wind pressures and wind loads on the solar collector. The results presented in this paper are expected to be of considerable interest and of use to researchers and engineers involved in analysis and design of parabolic trough solar collectors.     

Numerical and experimental investigation of parabolic trough collector with focal evacuated tube and different working fluids integrated with single slope solar still

This study deals with the design and fabrication of parabolic trough solar collectors (PTCs) used to increase the yield of a single slope solar still. The designed parabolic trough solar collector is investigated numerically using Ansys Fluent 18.2. The proposed solar still is coupled with a parabolic trough solar collector with an evacuated tube receiver in its focal axis using different working fluids. The working fluids are water (case 1), oil (case 2), and nano-oil (CuO/mineral oil 3% vol; case 3). In the case when the working fluid is not water, then a heat exchanger serpentine should be used in the solar still basin. The PTC has a rim angle of 82° and an aperture width of 0.9 m and length of 2.8 m. An assessment of the performance for the studied systems was accomplished under the weather conditions of Ismailia, Egypt, during summer months, June, July, and August 2019. The outcomes of closed-loop working fluids different flow rates are investigated. The experimental results of the accumulated freshwater productivities record 2.955, 3.475, 4.29, and 5.04 L m⁻² d⁻¹ for the traditional solar still and the modified cases 1 to 3 solar stills, respectively. The modified solar still in case 3 has the highest daily accumulated freshwater productivity with a percentage increase of 71.2% than the traditional solar still. The maximum daily efficiency is 46% and 26.9% for the traditional and modified (case 3) solar stills, respectively. The cost of 1 L of fresh water is 0.057 and 0.062 $/L for the traditional and the modified (case 3) solar stills, respectively.     

Performance evaluation of v-trough solar concentrator for water desalination applications

The working principle and thermal performance of a new v-trough solar concentrator are presented in this paper. Compared with the common parabolic trough solar concentrators, the new concentrator has two parabolic troughs which form a V-shape with the focal line at the bottom of the troughs. This is beneficial for the installation and insulation of the receiver, and the shadow on the reflective surface is avoided. The new v-trough collector does not require high precision tracking devices and reflective material. And therefore the cost of the system could be significantly reduced. Various experimental tests were carried out both outdoor and indoor using different types of receiver tubes. The results show that the collector system can have thermal efficiency up to 38% at 100 °C operating temperature. System modelling was used to predict the rate of fresh water produced by four different solar collector systems which include both static and one-axis solar tracking technologies. Comparison of the solar collectors at different temperature ranges for humidification/dehumidification desalination process using specific air flow rate were considered. At each temperature range, suitable solar collectors were compared in the aspect of fresh water production and area of solar collector required. Results showed that the new v-trough solar collector is the most promising technology for small to medium scale solar powered water desalination.