Effect of CuO on self-lubricating properties of ZrO2(Y2O3)–Mo composites at high temperatures

In this paper, ZrO₂ matrix high-temperature self-lubricating composites with addition of CuO as lubricant were prepared using a hot-pressing method by tailoring the content of CuO. The wear and friction behaviour of the composites were investigated from 700 °C to 1000 °C. The composites sliding against an Al₂O₃ ceramic ball exhibited excellent self-lubricating and anti-wear properties at high temperatures. The low friction and wear mechanisms were investigated in detail.     

Influence of the SiC grain size on the wear behaviour of Al2O3/SiC composites

Dry ceramic block-on-steel ring wear tests were performed at high loads in several Al₂O₃/20 vol.% SiC composites as a function of the SiC grain size, which ranged from 0.2 to 4.5 μm in d₅₀. The wear resistance of the monolithic alumina was radically improved by the addition of the SiC particles, reducing down to one order of magnitude wear rate. Two different behaviours were identified according to the microstructural observations on the worm surfaces: intergranular fracture and grain pull-out in the monolithic Al₂O₃, and plastic deformation and surface polishing in the composites. The wear resistance of the Al₂O₃/SiC composites increased with the SiC grain size due to their fracture toughness enhancement.     

Effect of Al2O3 on the microstructure and mechanical properties of Ti3AlC2/Al2O3 in situ composites synthesized by reactive hot pressing

Ti₃AlC₂/Al₂O₃ in situ composites with different Al₂O₃ contents were successfully synthesized from the powder mixture of Ti, TiC, Al and TiO₂ by a reactive hot-pressing method at 1350 °C. The effect of Al₂O₃ on the microstructure and mechanical properties of the composites was investigated in detail. The results indicate that the as-fabricated products mainly consist of Ti₃AlC₂, Al₂O₃ and a small amount of TiC. With increasing the Al₂O₃ content, the flexural strength of Ti₃AlC₂/Al₂O₃ composites increase gradually, the fracture toughness reaches the peak value of 8.21 MPa m^1/2 as the Al₂O₃ content increasing to 9 wt%, the hardness attains the maximum value of 10.16 GPa for 12 wt% Al₂O_3. The strengthening mechanism of the composites was also discussed.     

TEM investigations of wear mechanism of Al2O3 and Si3N4 compacts with GLPs additions

Extended lifetime of ceramic cutting plates is ever more desired. One way of approaching it entails sintering precursor materials with graphene-like nanoplatelets (GLPs) acting as solid lubricants. Therefore, Al₂O₃ and Si₃N₄ ceramic powders with addition of GLPs of grade 3 (fine) or grade 4 (coarse) were Spark Plasma Sintered. It is found that the 0.15 wt% GLPs addition of both grades allows to keep hardness practically at the same level as GLPs-free compacts (~16 GPa). Only larger GLPs additions (2 wt%) caused its evident decrease (down to 14−15 GPa). The ball-on-disc test revealed that only Al₂O₃+0.15 wt% GLPs(3) shows a 50% reduction in wear rate. The post mechanical test examination by SEM confirmed that Al₂O₃ compacts with small GLPs showed smooth wear track, as opposed to those having a Si₃N₄ matrix with large meandering cavities. TEM observations revealed that the wear damage caused by the ball was restricted to ~2 µm deep sub-surface areas, while, carbon is found to transfer from the GLPs agglomerates into tribo-film. The present experiments showed, that ceramic sinters with small addition of GLPs platelets could exhibit lower wear than GLPs-free ones and therefore show a potential for application as cutting plates.     

Fabrication and mechanical properties of Al2O3-SiCw-TiCnp ceramic tool material

Whiskers and nanoparticles are usually used as reinforcing additives of ceramic composite materials due to the synergistically toughening and strengthening mechanisms. In this paper, the effects of TiC nanoparticle content, particle size and preparation process on the mechanical properties of hot pressed Al₂O₃-SiC_w ceramic tool materials were investigated. The results showed that the Vickers hardness and fracture toughness of the materials increased with the increasing of TiC content. The optimized flexural strength was obtained with TiC content of 4 vol% and particle size of 40 nm. The particle size has been found to have a great influence on flexural strength and small influence on hardness and fracture toughness. It was concluded that the flexural strength increased remarkably with the decreasing of the TiC particle size, which was resulted from the improved density and refined grain size of the composite material due to the dispersion of the smaller TiC particle size. SEM micrographs of fracture surface showed the whiskers to be mainly distributed along the direction perpendicular to the hot-pressing direction. The fracture toughness was improved by whisker crack bridging, crack deflection and whisker pullout; the TiC nanoparticles in Al₂O₃ grains caused transgranular fracture and crack deflection, which improved the flexural strength and fracture toughness with whiskers synergistically. Uniaxial hot-pressing of SiC whisker reinforced Al₂O₃ ceramic composites resulted in the anisotropy of whiskers’ distribution, which led to crack propagation differences between lateral crack and radical crack.     

Preparation and performance of an advanced multiphase composite ceramic material

According to the optimum composition achieved from the material design, an advanced 15 vol.% SiC and 15 vol.% Ti(C,N) containing alumina-based multiphase ceramic material with good comprehensive mechanical properties has been fabricated with hot pressing technique. Only under suitable hot pressing conditions and material compositions can better microstructures and mechanical properties be achieved. The optimum hot pressing parameters for the SiC/Ti(C,N)/Al₂O₃ material are as follows: the hot pressing temperature is 1780 °C, the time duration equals to 60 min and the pressure remains 35 MPa. The content of each dispersed SiC and Ti(C,N) phase has significant effects not only on the mechanical properties but on the engineering performances of the ceramic materials. Good wear resistance is found for the kind of ceramic material when used as cutting tools in the machining of the hardened carbon steel. Failure mechanisms are mainly the abrasive wear and the adhesive wear. The developed SiC/Ti(C,N)/Al₂O₃ multiphase ceramic material will be well used as the structural parts with the requirement of high wear resistance such as cutting tools.     

Microstructure and mechanical properties of hot-pressed B4C/TiC/Mo ceramic composites

Boron carbide (B₄C)/TiC/Mo ceramic composites with different content of TiC were produced by hot pressing. The effect of TiC content on the microstructure and mechanical properties of the composites has been studied. Results showed that chemical reaction took place for this system during hot pressing sintering, and resulted in a B₄C/TiB₂/Mo composite with high density and improved mechanical properties compared to monolithic B₄C ceramic. Densification rates of the B₄C/TiC/Mo composites were found to be affected by additions of TiC. Increasing TiC content led to increase in the densification rates of the composites. The sintering temperature was lowered from 2150 °C for monolithic B₄C to 1950 °C for the B₄C/TiC/Mo composites. The fracture toughness, flexural strength, and hardness of the composites increased with increasing TiC content up to 10 wt.%. The maximum values of fracture toughness, flexural strength, and hardness are 4.3 MPa m^1/2, 695 MPa, and 25.0 GPa, respectively.     

Preparation and characterization of Al2O3/TiC micro–nano-composite ceramic tool materials

An Al₂O₃-based composite ceramic tool material reinforced with micro-scale and nano-scale TiC particles was fabricated by a hot-pressing technology with cobalt additive in different sintering processes. The microstructure, indention cracks and phase composition of composites were characterized with scanning electron microscopy, transmission electron microscopy and X-ray diffraction. The experimental results showed that Al₂O₃/TiC_μ/TiC_n micro–nano-composite containing 6 vol% nano-scale TiC and 35 vol% micro-scale TiC, which were sintered under a pressure of 32 MPa at a temperature of 1650 °C in vacuum for 20 min, had optimum mechanical properties. The addition of both nano-scale TiC and Co contributed to the microstructure evolution and the improvement of mechanical properties. Effects of nano-scale TiC on mechanical properties were investigated. The toughening and strengthening mechanisms of micro–nano-composites were discussed.     

Ti3Si(Al)C2-based ceramics fabricated by reactive melt infiltration with Al70Si30 alloy

Dense Ti₃Si(Al)C₂-based ceramics were synthesized using reactive melt infiltration (RMI) of Al₇₀Si₃₀ alloy into the porous TiC preforms. The effects of the infiltration temperature on the microstructure and mechanical properties of the synthesized composites were investigated. All the composites infiltrated at different temperatures were composed of Ti₃Si(Al)C₂, TiC, SiC, Ti(Al, Si)₃ and Al. With the increase of infiltration temperature from 1050 °C to 1500 °C, the Ti₃Si(Al)C₂ content increased to 52 vol.% and the TiC content decreased to 15 vol.%, and the Vickers hardness, flexural strength and fracture toughness of Ti₃Si(Al)C₂-based composite reached to 9.95 GPa, 328 MPa and 4.8 MPa m^1/2, respectively.     

The contribution of waste in the construction of composite materials

(3Ni + Fe)–Al₂O₃ and Ni₃Fe–Al₂O₃ composites were constructed using Ni, Fe and Ni₃Fe powders (μm), recovered from metallic waste (ferrous scrap) by a hydrometallurgical process, along with a 0–35 wt.% of commercial α-Al₂O₃ powder (0–55 vol.% theoretically). Established PM fabrication processes were applied. The successfully prepared metal–ceramics were characterized, and measurements of their physico-mechanical properties were conducted. The composite microstructures exhibit a residual porosity varying with the percent ceramic content and influenced by a certain degree of agglomeration revealed in the ceramic phase as well as by use of fabrication additives. When increasing percent ceramic amount, the composite materials become lighter, harder, stiffer and slightly stronger, while remaining conductive, although their electrical resistivity increases. Due to differences in matrix composition, Ni₃Fe–Al₂O₃ composites prevail over the (3Ni + Fe)–Al₂O₃ ones in hardness, and slightly in stiffness and strength, at each percent ceramic content.     

Synthesis of monolithic alumina-silica hollow microspheres and their heat-shielding performance for adiabatic materials

Al₂O₃ ceramic foams-based composites were firstly synthesized to be used as the thermal insulation material which has excellent mechanical properties of the substrate material and better thermal properties of hollow microspheres. In this research, by doping TEOS, the monolithic hollow microspheres were prepared via a novel and effective synthesis route using propylene oxide as the gelation initiator to induce the gelation of aluminum chloride hexahydrate solution. The influence of TEOS on the morphology and high-temperature stability of the monolithic hollow microspheres was clarified in detail. Based on the optimized additive amount of TEOS, Al₂O₃ ceramic foams were introduced as the substrate material of alumina-silica hollow microspheres to fabricate the final Al₂O₃ ceramic foams-based composites. Benefited from this special structure, the Al₂O₃ ceramic foams-based composites displayed excellent mechanical properties and thermal properties. The samples changed less in appearance and did not show significant shrinkage after heat-treatment at 1200 °C. The density, bending strength and thermal conductivity of the Al₂O₃ ceramic foams-based composite were 0.32 g/cm³, 1.8 MPa and 0.12 W/m K, respectively.     

Synthesis,microstructure and mechanical properties of Cr2AlC/Al2O3 in situ composites by reactive hot pressing

Al₂O₃ particle-reinforced Cr₂AlC in situ composites were successfully fabricated from powder mixtures of Cr₃C₂, Cr, Al, and Cr₂O₃ by a reactive hot-pressing method at 1400 °C. A possible synthesis mechanism was proposed to explain the formation of the composites in which Al₂O₃ was formed by the aluminothermic reaction between Al and Cr₂O₃, meanwhile, Cr₃C₂, Al, together with Cr reacted to form Cr₂AlC in a shortened reaction route. The effect of Al₂O₃ addition on the microstructure and mechanical properties of Cr₂AlC/Al₂O₃ composites was investigated. The results indicated that the as-sintered products consisted of Cr₂AlC matrix and Al₂O₃ reinforcement, and the in situ formed fine Al₂O₃ particles dispersed at the matrix grain boundaries. The flexural strength and Vickers hardness of the composites increased gradually with increasing Al₂O₃ content. But the fracture toughness peaked at 6.0 MPa m^1/2 when the Al₂O₃ content reached 11 vol.%. The strengthening and toughening mechanism was also discussed.     

Design and processing of Al2O3–Al2TiO5 layered structures

Al₂O₃–Al₂TiO₅ layered composites were manufactured by a colloidal route from aqueous Al₂O₃ and TiO₂ suspensions with 50 vol.% solids. The mechanical behaviours of individual monolithic composite materials were combined and taken as basis for the design of the layered structures. Residual stresses which are likely to occur due to processing and thermally introduced misfits were calculated and considered for the manufacture of the laminates.Monoliths with 10, 30 and 40 vol.% of second phase showed that increasing proportions of aluminium titanate decrease strength and increase the non-linear behaviour.In order to obtain the desired combination of mechanical behaviours of the layers, two laminate designs with external and central layers of one composition and the alternating internal layer of the other composition were chosen taking into account chemical compatibility and development of residual stresses. In the system AA10, external and central layers of monophase Al₂O₃ with high strength were combined with intermediate layers of Al₂O₃ with 10 vol.% of Al₂TiO₅. The system A10A40 was selected to combine low strength and energy absorbing intermediate layers of Al₂O₃ with 40 vol.% of Al₂TiO₅ and sufficient strength provided by external layers of Al₂O₃ with 10 vol.% of Al₂TiO₅.The stress–strain behaviour of the laminates was linear up to their failure stresses, with apparent strain for zero load after fracture larger than that corresponding to the monoliths of the same composition as that of the external layers. Moreover, the stress drop of the laminate samples occurred in step-like form thus suggesting the occurrence of additional energy consuming processes during fracture.     

Carbon nanotube toughened aluminium oxide nanocomposite

This paper describes the mechanical properties of carbon nanotube-reinforced Al₂O₃ nanocomposites fabricated by hot-pressing. The results showed that compared with monolithic Al₂O₃ the fracture toughness, hardness and flexural strength of the nanocomposites were improved by 94%, 13% and 6.4% respectively, at 4 vol.% CNT additions. For 10 vol.% CNT additions, with the exception of the fracture toughness, which was improved by 66%, a decrease in mechanical properties was observed when compared with those for monolithic Al₂O₃. The toughening mechanism is discussed, which is due to the uniform dispersion of CNTs within the matrix, adequate densification, and proper CNT/matrix interfacial connections.     

Fast preparation of ZTA-TiC-FeCrNi cermets by high-gravity combustion synthesis

ZTA-TiC-FeCrNi cermets are prepared by a fast and furnace-free way called high-gravity combustion synthesis. The synthesized cermet samples show the maximum relative density of 97.6% and a hierarchical microstructure with grain sizes from submicron to >50 µm. The content of TiC has a strong influence on the microstructure and mechanical properties of the cermet samples. A higher TiC content results in refined microstructure, improved hardness, and reduced coefficient of friction. With increasing TiC content, the strength and toughness of the samples first increase and then drops, and reach the maximum of 469±26 MPa and 11.3±0.2 MPa m^1/2 at 20% TiC. Compared with commercial polycrystalline Al₂O₃ ceramics, the ZTA-TiC-FeCrNi cermets exhibit better wear resistance, and the volume loss is lower by one magnitude than Al₂O₃ under the same condition.     

Improved mechanical properties of Al2O3 ceramic by in-suit generated Ti3SiC2 and TiC via hot pressing sintering

Al₂O₃ multi-phase composites with different volume fractions of SiC varying from 0 vol% to 30.0 vol% were fabricated by vacuum hot pressing sintering at 1600 °C under the pressure of 30 MPa for 2.0 h. The aim of this work was to investigate the effect of SiC content on the morphology and mechanical properties of the Al₂O₃ multi-phase composite. The results show that the addition of SiC and Ti can produce new strengthening and reinforcing phases include Ti₃SiC₂, TiC, Ti₅Si₃, which would hamper the migration of grain boundaries and promote sintering. The mechanical performances could reach the comprehensive optimal values for 20.0 vol% SiC, delamination and transgranular fracture being the major crack propagation energy dissipation mechanisms.     

Effect of graphene addition on the mechanical and electrical properties of Al2O3-SiCw ceramics

This paper presents a study on graphene-reinforced Al₂O₃-SiCw ceramic composites and the relationship between graphene oxide (GO) loading and the resulting mechanical and electrical properties. Well-dispersed ceramic-GO powders were fabricated using a colloidal processing route. Dense composites were obtained via spark plasma sintering, a technique that has the ability to reduce GO to graphene in situ during the sintering process. The mechanical properties of the sintered composites were investigated. The composite with only a small amount of graphene (0.5 vol.%) showed the highest flexural strength (904 ± 56 MPa), fracture toughness (10.6 ± 0.3 MPa·m^1/2) and hardness (22 ± 0.8 GPa) with an extremely good dispersion of graphene within the ceramic matrix. In addition to these exceptional mechanical properties, the sintered composites also showed high electrical conductivity, which allows the compacts to be machined using electrical discharge machining and thus facilitates the fabrication of ceramic components with sophisticated shapes while reducing machining costs.     

Effect of graphite nanoplatelets on the mechanical properties of alumina-based composites

Al₂O₃-based composites using exfoliated graphite nanoplatelets (xGnPs) have been developed by powder metallurgy (PM) route using both conventional as well as spark plasma sintering (SPS) processes. Al₂O₃-0.2, 0.5, 0.8, 3 and 5 vol% xGnP composites have been developed, and the effect of the addition of xGnP on the density, hardness, fracture toughness and wear behaviour of the various Al₂O₃-xGnP composites have been analyzed. Conventional sintering was done at a temperature of 1650 °C for 2, 3 and 4 h in inert atmosphere, whereas SPS was carried out at 1450 °C under 50 MPa pressure for 5 min. A uniform dispersion of the xGnP in the Al₂O₃ matrix was observed in the composites upto the addition of 3 vol% xGnP. Results indicate that a significant improvement in hardness, wear resistance and fracture toughness of the composites could be achieved by using xGnP as nanofiller. The hardness and fracture toughness of the composites developed by both conventional sintering and SPS show an increase upto the addition of 3 and 0.8 vol% xGnP respectively. The wear resistance of the composites also shows significant improvement upto the addition of 3 vol% xGnP. The composites developed by SPS have been found to possess superior mechanical properties as compared to the composites developed by conventional sintering. The improvement in the mechanical properties can be attributed to the strong interaction between the xGnP and the Al₂O₃ matrix at the interfaces and to the toughening mechanisms such as crack bridging and crack deflection.     

Mechanical properties and sliding wear behaviour of Al2O3-SiC nanocomposites with 3–20 vol% SiC

Al₂O₃/SiC composites containing different volume fractions (3, 5, 10, 15, and 20 vol%) of SiC particles were produced by conventional mixing of alumina and silicon carbide powders, followed by hot pressing at 1740 °C for 1 h under the pressure of 30 MPa in the atmosphere of Ar. The influence of the volume fraction and size of SiC particles (two different powders with the mean size of SiC particles 40 and 200 nm were used), and final microstructure on mechanical properties and dry sliding wear behaviour in ball-on-disc arrangement were evaluated. The properties of the composites were related to a monolithic Al₂O₃ reference. Microstructure of the composites was significantly affected by the volume fraction of added SiC, with the mean size of alumina matrix grains decreasing with increasing content of SiC particles. The addition of SiC moderately improved the Vickers hardness. Fracture toughness was lower with respect to monolithic Al₂O₃, irrespective of the volume fraction and size of SiC particles. Al₂O₃/SiC nanocomposites conferred significant benefits in terms of wear behaviour under the conditions of mild dry sliding wear. Wear resistance of the alumina reference was poor, especially at the applied load of 50 N. The wear rates of composites markedly decreased with increasing volume fraction of SiC. Wear of the composites was also influenced by the material of counterparts, especially their hardness, with softer counterparts resulting in lower wear rates. All composites wore by a combination of grain pull-out with plastic deformation associated with grooving and small contribution of mechanical wear (micro-fracture). No influence of SiC particle size on wear rate or mechanism of wear was observed in the materials with identical volume fractions of SiC.     

Effect of preparation route on the properties of slip-casted Al2O3/YAG composites

Alumina composites containing 5, 10 and 20 vol.% YAG were produced by a slip-casting process. Two different routes for adding the YAG phase were chosen. Either by mixing of alumina with previously produced YAG powder or by coating of an adequate amount of yttria to form YAG precipitates during the calcining step. The mechanical properties of the sintered samples were measured and compared. Independent from the preparation route Al₂O₃/10 vol.% YAG composites showed best mechanical properties. Significant differences in the densification behavior appeared between the two different manufacturing technologies. The presence of intermediately formed phases like YAM and YAP during the powder preparation step of coated composites is probably the reason why mixed composites showed higher mechanical properties than coated composites.