Fabrication and characterization of cordierite-bonded porous SiC ceramics

A reaction bonding technique was used for the preparation of cordierite-bonded porous SiC ceramics in air from α-SiC, α-Al₂O₃ and MgO, using graphite as the pore-forming agent. Graphite was burned out to produce pores and the surface of SiC was oxidized to SiO₂ at high temperature. With further increasing the temperature, SiO₂ reacted with α-Al₂O₃ and MgO to form cordierite. SiC particles were bonded by the cordierite and oxidation-derived SiO₂. The reaction bonding characteristics, phase composition, open porosity, pore size distribution and mechanical strength as well as microstructure of porous SiC ceramics were investigated. The pore size and porosity were strongly dependent, respectively, on graphite particle size and volume fraction. The porous SiC ceramics sintered at 1350 °C for 2 h exhibited excellent combination properties, the flexural strength of 26.0 MPa was achieved at an open porosity of 44.51%.     

Enhancement of bonding network for silica sol bonded SiC castables by reactive micropowder

Silica sol bonded castables have obvious advantages over low cement or hydratable alumina bonded castables in drying performance and sintering properties for SiC castables. However, they are not widely used due to their weak strength at low temperature. The efficiency of bonding network for silica sol bonded SiC castable in the presence of different reactive micropowder such as SiO₂ micropowder and α-Al₂O₃ micropowder was evaluated through oscillatory tests, sintered properties and microstructural analysis. Results show that the polymerization reaction between SiO₂ micropowders enhanced the siloxane network and reinforced the bonding strength, furthermore, the addition of α-Al₂O₃ micropowder contributed to accelerating the formation of the siloxane network and hardening of the silica sol at lower temperatures and shorter time. Silica sol performed well as a binder agent for SiC castables with an addition content of 3 wt% SiO₂ micropowder and 2 wt% α-Al₂O₃ micropowder, which showed high strength and good workability at room temperature. And Silica sol bonded SiC castable with the above micropowder contents possessed the best mechanical behavior after heat treatment due to combined binding of SiC whiskers and mullite.     

The fabrication of porous mullite ceramics based on the different sizes of aluminum hydroxide

In this research, for studying the influence of size and heat treatment temperature of initial Al(OH)₃ on the physical properties of porous mullite ceramics, porous mullite ceramics were prepared by in situ reaction sintering of amorphous silica and treated Al(OH)₃. The transition phases χ-Al₂O₃, к-Al₂O₃, and stable phase α-Al₂O₃ can be obtained in turn when the treatment temperature of raw Al(OH)₃ is 500, 1000, and 1500°C, respectively. The coarser the raw Al(OH)₃, the higher the strength of porous mullite ceramics. When the sintering temperature is 1500°C, the bending strengths of PS500-C, PS1000-C, and PS1500-C (PSx-C represents that the specimen was prepared by the coarse grade Al(OH)_3, which was previously treated at x°C) are 40.3 ± 2.1, 54.9 ± 5.2, and 64.8 ± 4.8 MPa, respectively. In addition, although the activated Al₂O₃ can decrease the formation temperature (∼100°C) of porous mullite ceramics, the strength and density of porous mullite ceramics prepared by activated Al₂O₃ will decrease at the same sintering temperature. It is believed that the increase of defects and pores during the phase transformation should be responsible for this phenomenon.     

Fabrication and properties of porous mullite ceramics from calcined carbonaceous kaolin and α-Al2O3

High purity calcined carbonaceous kaolin and α-Al₂O₃ powders were employed to prepare porous mullite ceramics (Sample A) using graphite as pore former with the reaction sintering method. For the purpose of comparison, porous mullite ceramics (Sample B) was also fabricated from the uncalcined carbonaceous clay incorporated with α-Al₂O₃ powders. Mullitization in the two samples was both nearly complete at 1500 °C, despite the fact that calcination of the clay remarkably depressed mullitization and promoted the formation of glass phase. The Sample A sintered at 1500 °C fractured mainly in an intergranular way, while the Sample B mainly underwent transgranular fracture. The experimental results revealed that densification behavior/open porosity of the Sample A was far more sensitive to sintering temperature. The pore size of the Sample A as well as the Sample B sintered at 1500 °C was in a narrower range of 0.3–5 μm.     

Effects of Al2O3 crystal types on morphologies,formation mechanisms of mullite and properties of porous mullite ceramics based on kyanite

Porous mullite ceramics with different crystal shapes of mullite are fabricated by in-situ reaction with middle-grade kyanite as raw material, Al(OH)₃, γ-Al₂O₃, ρ-Al₂O₃ and α-Al₂O₃ as alumina sources. Effects of Al₂O₃ crystal types on morphology evolution and formation mechanisms of mullite, and properties of porous ceramics are investigated. Results show that mullite in the sample with Al(OH)₃ mainly shows acicular morphology, because its (001) plane has the minimum interplanar crystal spacing and maximal attachment energy, it grows fast along [001] direction by screw dislocation mechanism. With a successive slowdown in reactivities of Al(OH)₃, γ-Al₂O₃, ρ-Al₂O₃ and α-Al₂O₃, the amount and aspect ratio of mullite reduce, its growth mechanism gradually transforms into two-dimensional nucleation. Acicular mullite not only reinforces samples, but makes effective pore sizes smaller, which enable the sample with Al(OH)₃ to present low bulk density, high apparent porosity and linear changes, small average pore size and good mechanical strength.     

Influence of ZrO2 and WO3 doping additives on the thermal properties of porous mullite ceramics

Porous mullite-corundum refractory ceramics were produced by a patented slurry slip casting method from compositions based on commercially available α-Al₂O₃ and γ-Al₂O₃, fused SiO₂ and kaolin. Pores were formed as a result of a chemical reaction of aluminium with water. The influence of usage of raw materials and doping additives such as micro-size ZrO₂ and WO₃ on the sintering temperature, formation of crystalline phases, linear thermal expansion, thermal conductivity and thermal shock resistance of mullite-corundum ceramic was studied. The best thermal shock resistance and, simultaneously, lower thermal conductivity was achieved for the samples doped with WO₃. This was due to the influence of micro-sized WO₃ on the change in γ-Al₂O₃ modification to α-Al₂O₃ and on the structure of mullite ceramics.     

Temperature-induced fibre/matrix interactions in porous alumino silicate ceramic matrix composites

The thermal stability of alumino-silicate fibre (Nextel 720)/porous mullite matrix composites was investigated in the temperature range between 1300 and 1600°C. In the as-prepared state the fibres consist of mullite plus α-Al₂O₃, while the porous mullite matrix includes minor amounts of a SiO₂-rich glass phase. Temperature-controlled reactions between the silica-rich glass phase of the matrix and α-Al₂O₃ at the rims of the fibres to form mullite have been observed. At the end of this process, virtually all glass phase of the matrix is consumed. Simultaneously, alumina-free layers about 1 μm thick are formed at the periphery of the fibres. The mullite forming process is initiated above about 1500°C under short time heat-treatment conditions (2 h) and at much lower temperature (1300°C) under long-term annealing (1000 h). Subsequent to annealing below the thermal threshold, the composite is damage tolerant and only minor strength degradation occurs. Higher annealing temperatures, however, drastically reduce damage tolerance of the composites, caused by reaction-induced gradually increasing fibre/matrix bonding. According to this study, the thermal stability of alumino silicate (Nextel 720) fibre/mullite matrix composites ranges between 1500°C in short-term and 1300°C in long-term heat-treatment conditions.     

Sintering of α-Al2O3—Amorphous silica compacts

Sintering of α-Al₂O₃—fused SiO₂ compacts at temperatures of 1350–1500 °C is affected by metastable and stable phase reactions. Shrinkage maxima in the range 10 to 30 mole % Al₂O₃ are the result of cristobalite in the fused SiO₂ and its reaction with α-Al₂O₃ to form the eutectic of the metastable phase equilibrium diagram for SiO₂ (cristobalite)—α-Al₂O₃ without mullite. The retardation of densification of α-Al₂O₃ compacts with additions of SiO₂ up to about 50 mole % at temperatures about 1400°C and above is associated with the appearance of mullite.     

Fabrication and Characterization of Near‐Net‐Shape In Situ Reaction‐Bonded Porous Cordierite/SiC Ceramics

Porous cordierite/SiC ceramics were fabricated by in situ reaction bonding using α‐SiC, α‐Al₂O_3, and MgO powders as the starting materials. During sintering, part SiC is oxidized to SiO₂ and then the latter reacts with Al₂O₃ and MgO to form cordierite. As a result, porous cordierite/SiC ceramics were obtained, and the ceramics are strengthened by the residual SiC. Due to the large volume expansion introduced by the oxidation of SiC, the ceramics exhibit small sintering‐induced dimension variations. In addition, a fine‐grained microstructure and good thermal and mechanical properties were obtained for the porous cordierite/SiC ceramics.     

In situ formation of mullite strengthened SiC porous ceramics via gelcasting with high strength and good alkali resistance

Mullite-bonded porous SiC ceramics sintered in air by gelcasting are still challenges due to the high porosity induced severe oxidation of SiC, which results in the formation of large amount of detrimental cristobalite phase. Here in this work, small amounts of Y₂O₃ and CaF₂ were added in SiC and Al(OH)₃ raw materials as sintering additives for the in situ growth of mullite reinforcement. This additive system promoted the reaction between oxidation-derived SiO₂ from SiC and Al₂O₃ decomposed from Al(OH)₃ to mullite phase. Almost no cristobalite phase was detected when sintered at 1450℃/2 h with CaF₂ addition of more than 2.0 wt%. Mullite whisker reinforcement was in situ formed due to the gas reaction mechanism caused by CaF₂ addition. Thus obtained porous SiC ceramics exhibited a flexural strength of 67.6 MPa at porosity of 41.3%, which maintained exceeding 36 MPa after 8 h corrosion in 10 wt% NaOH 80℃ solution, being the best performance up to now. This high performance of porous SiC was attributed to the additive induces proper phase control and in situ formation of whisker-like mullite reinforcement.     

Effect of mullite phase formed in situ on pore structure and properties of high-purity mullite fibrous ceramics

Porous mullite ceramics are potential advanced thermal insulating materials. Pore structure and purity are the main factors that affect properties of these ceramics. In this study, high performance porous mullite ceramics were prepared via aqueous gel-casting using mullite fibers and kaolin as the raw materials and ρ-Al₂O₃ as the gelling agent. Effects of addition of mullite fibers on the pore structure and properties were examined. The results indicated that mullite phase in situ formed by kaolin, and ρ-Al₂O₃ ensured the purity of mullite samples and mullite fibers bonded together to form a nest-like structure, greatly improving the properties of ceramic samples. In particular, the apparent porosity of mullite samples reached 73.6%. In the presence of 75% of mullite fibers, the thermal conductivity was only 0.289 W/m K at room temperature. Moreover, the mullite samples possessed relatively high cold compressive strength in the range of 4.9–9.6 MPa. Therefore, porous mullite ceramics prepared via aqueous gel-casting could be used for wide applications in thermal insulation materials, attributing to the excellent properties such as high cold compressive strength and low thermal conductivity.     

Fabrication and properties of porous anorthite/mullite ceramics with both high porosity and high strength

Porous anorthite/mullite ceramics with both high porosity and high strength have been successfully fabricated by foam-gelcasting and pressureless sintering technology, using α-Al₂O₃, SiO₂, and CaCO₃ as starting materials and MnO₂ as sintering aids. The porous mullite ceramics prepared in this study had 83.3% porosity and 0.3 W/m·K thermal conductivity, exhibited compressive strength value as high as 6.1 MPa. The samples fabricated with mullite content of 30 mol% possessed 79.4% porosity and 5.9 MPa compressive strength showed thermal conductivity as low as 0.19 W/m·K. With the addition of MnO₂, the properties of the prepared materials varied slightly when mullite content changed in a large scale. The results showed that the addition of MnO₂ promoted the reaction, affected sintering and grain growth, and contributed to high strength and low-thermal conductivity.     

Recycling of waste red mud for fabrication of SiC/mullite composite porous ceramics

SiC/mullite composite porous ceramics were fabricated from recycled solid red mud (RM) waste. The porous ceramics were formed using a graphite pore forming agent, RM, Al(OH)₃ and SiC in the presence of catalysts. The influence of firing temperature and the pore-forming agent content on the mechanical performance, porosity and the microstructure of the porous SiC ceramics were investigated. Optimal preparation condition were determined by some testing. The results indicated that the flexural strength of specimens increased as a function of firing temperature and a reduction in graphite content, which concomitantly decreased porosity. The ceramic prepared under optimal conditions having 15?wt% graphite and sintered at 1350?°C, demonstrated excellent performance. Under optimal preparation conditions the flexural strength and porosity of the ceramic were 49.4?MPa and 31.4%, respectively. Scanning electron microscopy observation result showed that rod-shape mullite grains endowed the samples with high flexural strength and porosity. X-ray diffraction analysis indicated that the main crystallization phases of the porous ceramics were 6H-SiC, mullite, cristobalite and alumina. This work demonstrates that RM can be sucessfully reused as a new raw material for SiC/mullite composite porous ceramics.     

Preparation and properties of porous SiC–Al2O3 ceramics using coal ash

In this paper, we first reported that porous SiC–Al₂O₃ ceramics were prepared from solid waste coal ash, activated carbon, and commercial SiC powder by a carbothermal reduction reaction (CRR) method under Ar atmosphere. The effects of addition amounts of SiC (0, 10, 15, and 20 wt%) on the postsintering properties of as-prepared porous SiC–Al₂O₃ ceramics, such as phase composition, microstructure, apparent porosity, bulk density, pore size distribution, compressive strength, thermal shock resistance, and thermal diffusivity have been investigated. It was found that the final products are β-SiC and α-Al₂O₃. Meanwhile, the SEM shows the pores distribute uniformly and the body gradually contacts closely in the porous SiC–Al₂O₃ ceramics. The properties of as-prepared porous SiC–Al₂O₃ ceramics were found to be remarkably improved by adding proper amounts of SiC (10, 15, and 20 wt%). However, further increasing the amount of SiC leads to a decrease in thermal shock resistance and mechanical properties. Porous SiC–Al₂O₃ ceramics doped with 10 wt% SiC and sintered at 1600°C for 5 hours with the median pore diameter of 4.24 μm, room-temperature compressive strength of 21.70 MPa, apparent porosity of 48%, and thermal diffusivity of 0.0194 cm²/s were successfully obtained.     

Near-net-size preparation of porous mullite matrix ceramics with in situ formed 3D mullite whisker network

Porous mullite matrix ceramics have excellent thermal and mechanical properties suitable for applications such as in thermal insulation. However, their applications are limited by processing defects from nonuniform sintering shrinkage and the trade-off between high porosity (preferred for low thermal conductivity) and high mechanical strength. Herein, we seek to minimize the sintering shrinkage by near-net-size preparation and improve the strength by in situ formed whisker network structure. Gelcasting forming technology and pressureless sintering were used to prepare porous mullite matrix ceramics using kyanite and α-Al₂O₃ powders as the starting materials and using MoO₃ to promote the growth of mullite whiskers. The results showed that the sintering shrinkage could be compensated by the volume expansion from solid-state reaction during reaction sintering. The in situ formed three-dimensional (3D) whisker network further reduced sintering shrinkage and effectively improved the strength of the ceramics. An ultralow sintering shrinkage of .78% was achieved. The near-net-shape porous mullite matrix ceramics strengthened by 3D whisker network had a high porosity of 63.9%, a high compressive strength of 83.8 MPa and a high flexural strength of 53.5 MPa.     

Effect of SiC whiskers on the anti-oxidation properties of Yb2Si2O7/mullite/SiC tri-layer environmental barrier coating for CMCs

The mullite and ytterbium disilicate (β-Yb₂Si₂O₇) powders as starting materials for the Yb₂Si₂O₇/mullite/SiC tri-layer coating are synthesized by a sol–gel method. The effect of SiC whiskers on the anti-oxidation properties of Yb₂Si₂O₇/mullite/SiC tri-layer coating for C/SiC composites in the air environment is deeply studied. Results show that the formation temperature and complete transition temperature of mullite were 800–1000 and 1300°C, respectively. Yb₂SiO₅, α-Yb₂Si₂O₇, and β-Yb₂Si₂O₇ were gradually formed between 800 and 1000°C, and Yb₂SiO₅ and α-Yb₂Si₂O₇ were completely transformed into β-Yb₂Si₂O₇ at a temperature above 1200°C. The weight loss of Yb₂Si₂O₇/(SiC_w–mullite)/SiC tri-layer coating coated specimens was 0.15 × 10⁻³ g cm⁻² after 200 h oxidation at 1400°C, which is lower than that of Yb₂Si₂O₇/mullite/SiC tri-layer coating (2.84 × 10⁻³ g cm⁻²). The SiC whiskers in mullite middle coating can not only alleviate the coefficient of thermal expansion difference between mullite middle coating and β-Yb₂Si₂O₇ outer coating, but also improve the self-healing performance of the mullite middle coating owing to the self-healing aluminosilicate glass phase formed by the reaction between SiO₂ (oxidation of SiC whiskers) and mullite particles.     

Studies on processing of layered oxide-bonded porous sic ceramic filter materials

Oxide-bonded porous SiC ceramic filter supports were prepared using SiC powder (d₅₀ = 212 µm), Al₂O₃, and clay as bond forming additives and graphite as pore former following reaction bonding of powder compacts at 1400°C in air. Reaction bonding characteristics, phase composition, porosity, pore size, mechanical strength, and microstructure of porous SiC ceramic supports were investigated. Mullite bond phase formation kinetics was studied following the Johnson–Mehl–Avrami–Kolmogorov (JMAK) model using non-isothermal differential thermal analysis (DTA) data. Compared to porous SiC ceramic filter supports having no needle-like mullite bond phase, materials processed by the mullite bonding technique exhibited higher average strength (22.1%) and elastic modulus (5.4%) at a similar porosity level of ~38%, with upper and lower bounds of their strength, modulus, and porosity being 39.1 MPa, 40.2 GPa, and 36.3% and 34.2 MPa, 31.3 GPa, and 33.0%, respectively. Spray coating method was applied for preparation of oxidation-bonded SiC filtration layer having thickness of ~150 µm and pore size of ~5–20 µm over the porous SiC support compacts using aqueous slurry made of fine SiC powder (d₅₀ = 15 µm) followed by sintering. The layered ceramics thus prepared are potential materials for gas filter applications.     

Corrosion behaviors of porous reaction-bonded silicon carbide ceramics incorporated with CaO

Reaction-bonded SiC (RBSC) porous ceramics were fabricated at 1450?°C in air by incorporating CaO using ZrO₂ as sintering aids, activated carbon as pore-forming agent, and mullite fibers as reinforcing agent. The effects of CaO content on the properties of the porous RBSC ceramics were studied. Corrosion behaviors of the prepared RBSC porous ceramics in different environments were also investigated. The optimal open porosity, bending strength, average pore size and gas permeability of the ceramics with 0.5% CaO were 40%, 22.5?MPa, 42.9?µm, and 2100?m³/m² h?kPa, respectively. A well-developed neck reaction-bonded by calcium zirconium silicate (Ca₃ZrSi₂O₉) was identified. The porous RBSC ceramics exhibited excellent corrosion resistance in acid and basic solutions. The anti-oxidation temperature of the porous RBSC ceramics could reach 1200?°C in air. The RBSC ceramics maintained the bending strength of 17.5?MPa after 60 cold-hot cycles in air (0–800?°C). The porous RBSC ceramics also exhibited relatively good corrosion resistance in molten salts (NaCl, Na₂SO₄ and CaCl₂). Melten NaOH can aggravate the reaction by breaking the SiO₂ layers on the SiC surface. Overall, these findings offer significant insights into expanding the applications porous RBSC ceramics incorporated with CaO.     

In-situ synthesis and textural evolution of the novel carbonaceous SiC/mullite aerogel via polymer-derived ceramics route

A novel carbonaceous SiC/mullite composite aerogel is derived from catechol-formaldehyde/silica/alumina hybrid aerogel (CF/SiO₂/AlOOH) via polymer-derived ceramics route (PDCR). The effects of the reactants concentrations on the physicochemical properties of the carbonaceous SiO₂/Al₂O₃ aerogel and SiC/mullite aerogel are investigated. The mechanism of the textural and structural evolution for the novel carbonaceous SiC/mullite is further discussed based on the experimental results. Smaller reactants concentration is favorable to formation of mullite. Reactants concentration of 25% is selected as the optimal condition in considering of the mullite formation and bulk densities of the preceramic aerogels. Spherical large silica particles are also produced during heat treatment, and amorphous silica is remained after this reaction. With further heat treatment at 1400 °C, silicon carbide and mullite coexist in the aerogel matrix. The mullite addition decreases the temperature of SiC formation, when compared with the conventional methods. However, after heat treatment at 1450 °C, the amount of mullite begins to decrease due to the further reaction between carbon and mullite, forming more silicon carbide and alumina. The carbonaceous SiC/mullite can be transferred to SiC/mullite binary aerogel after carbon combustion under air atmosphere. The carbonaceous SiC/mullite has a composition of SiC (31%), mullite (19.1%), SiO₂ (14.4%), and carbon (35%). It also possesses a 6.531 nm average pore diameter, high surface area (69.61 m²/g), and BJH desorption pore volume (0.1744 cm³/g). The oxidation resistance of the carbonaceous SiC/mullite is improved for 85 °C when compared with the carbon based aerogel.     

Low thermal conductivity in porous SiC–SiO2–Al2O3–TiO2 ceramics induced by multiphase thermal resistance

The introduction of multiple heterogeneous interfaces in a ceramic is an efficient way to increase its thermal resistance. Novel porous SiC–SiO₂–Al₂O₃–TiO₂ (SSAT) ceramics were fabricated to achieve multiple heterogeneous interfaces by sintering equal volumes of SiC, SiO₂, Al₂O₃, and TiO₂ compacted powders with polysiloxane as a bonding phase and carbon as a template at 600 °C in air. The porosity could be controlled between 66% and 74% by adjusting the amounts of polysiloxane and the carbon template. The lowest thermal conductivity (0.059 W/(m·K) at 74% porosity) obtained in this study is an order of magnitude lower than those (0.2–1.3 W/(m·K)) of porous monolithic SiC, SiO₂, Al₂O₃, and TiO₂ ceramics at an equivalent porosity. The typical specific compressive strength value of the porous SSAT ceramics at 74% porosity was 3.2 MPa cm³/g.