等离子表面高铬高碳耐磨层的研究

采用等离子表面合金化技术,在20钢表面渗铬,并进行双辉等离子渗碳,形成高铬高碳合金层.利用GDS、XRD、OM、SEM研究了合金层成分、相组成及组织形貌,并通过摩擦试验对合金层耐磨性进行了分析.研究结果表明:表面高碳高铬层含铬量和含碳量以及碳化物的质量分数(40%以上)高于一般冶金高铬铸铁;渗层主要包含M23C6和M7C3型碳化物,这些碳化物均匀弥散分布,尺寸通常在1μm左右,并无共晶碳化物组织;合金层表面显微硬度达到1000～1600 HV,耐磨性比GCr15轴承钢提高8.6倍.     

Fe—C—Cr—V—B系高铬堆焊合金的显微组织及耐磨性

采用药芯焊丝埋弧堆焊方法制备含有C 1 2%～1 8%(质量分数,下同),Cr 15%～20%,V 2 0%～3 0%,B 0%～1 0%的高铬堆焊合金.借助光学显微镜、扫描电镜和X射线衍射等分析手段,研究其显微组织及碳化物分布形貌,结果表明:其显微组织由α-Fe+γ-Fe+(Fe, Cr)7C3+ (Fe, Cr)3C+Fe3(C, B)+B4C等组成,加入B4C可显著细化该堆焊合金晶粒,降低α-Fe,γ-Fe基体组织的Cr,V等合金元素的固溶量,使碳化物(Fe, Cr)7C3数量增加且呈弥散分布.另外,考察了B4C含量对高铬堆焊合金硬度及耐磨性的影响,耐磨粒磨损实验结果表明其相对磨损系数是H25Cr3Mo2MnV堆焊合金的6～17倍,其中碳化物颗粒四周均匀分布的α-Fe等基体组织使其可承受较大的磨粒冲击而不脱落.     

烧结Cr15高铬铸铁组织与性能的研究

为研发耐磨性能优良、成本相对低廉的高铬铸铁,本文分别以亚共晶、过共晶的水雾化Cr15高铬铸铁粉末为原料,采用超固相线液相烧结工艺制备了烧结高铬铸铁(SHCCI),并对其显微组织、力学性能和冲击磨粒磨损工况下的耐磨性能进行对比研究。结果表明,烧结高铬铸铁主要由M7C3碳化物、马氏体和奥氏体组成;在亚共晶烧结高铬铸铁中,通过电解腐蚀萃取的M7C3碳化物三维形貌呈珊瑚状,沿晶界均匀分布,材料抗冲击耐磨性能优良;在过共晶烧结高铬铸铁中,优先形成的初生碳化物可能成为共晶碳化物的生长基底,形成核-壳结构的M7C3碳化物,沿晶界相互连接呈网状,严重割裂基体。亚共晶、过共晶烧结高铬铸铁的力学性能分别为:硬度HRC63.9、HRC64.3,冲击韧性7.92、3.04 J/cm^2,抗弯强度2112.65、1624.87 MPa。     

添加Mo对高铬铸铁组织及亚临界处理硬化作用的影响研究

为提升高铬铸铁的综合性能,以无Mo高铬铸铁和含1.0％(质量分数)Mo高铬铸铁为研究对象,对比研究了添加Mo元素对铸态高铬铸铁组织结构以及550℃亚临界处理对其组织及硬度的影响.研究表明:2种铸态高铬铸铁的主要组成相均为奥氏体、马氏体及(Cr,Fe)7C3,但含Mo高铬铸铁中奥氏体含量明显增多.铸态高铬铸铁均以亚共晶方式结晶,其组织为初生树枝晶固溶体及其间的共晶组织组成,但含Mo高铬铸铁的树枝晶组织发生了明显细化.2种高铬铸铁经过550 ℃下不同保温时间的亚临界处理后均出现了硬化现象,但含Mo高铬铸铁的硬度峰值(50 HRC)比铸态硬度提高了31.6％,无Mo高铬铸铁的硬度峰值(48 HRC)比铸态硬度提高了14.2％;含Mo高铬铸铁的硬度峰值出现时间(15 h)长于无Mo高铬铸铁(5 h).Mo元素细化了高铬铸铁的枝晶组织,并提供了其亚临界处理后的硬化效果.     

铸态中铬硅铸铁价电子结构与M7C3体积分数

为提高中铬铸铁共晶碳化物中M7C3比例,研究了中铬硅铸铁(290Cr8Si2).建立了铸态中铬硅铸铁基体的价电子结构,运用固体与分子经验电子理论(EET)分析了中铬硅铸铁中Si的作用.分析和实验结果表明,中铬硅铸铁基体含C、Cr、Si的γ-Fe晶胞中,C原子与Si原子的结合力强于C原子与Cr原子的结合力,较高的含Si量降低了铸铁基体的含Cr量,提高了共晶碳化物的含Cr量,进而提高了共晶碳化物中M7C3的比例.耐磨损中铬硅铸铁(290Cr8Si2)共晶碳化物(M7C3 M3C)中M7C3占94.2%(体积分数),明显高于中铬铸铁(290Cr8Si1)共晶碳化物中的M7C3的71.7%(体积分数).     

硼白口铸铁的研究进展

白口铸铁的合金化主宰了其发展进程.介绍了硼合金化白口铸铁的研究状况,主要阐述了硼对以碳化物为耐磨相和以硼化物为耐磨相的白口铸铁中组织和性能的影响.硼不改变以碳化物为耐磨相的白口铸铁中碳化物的形态,但能提高碳化物硬度和基体的淬透性,对韧性没有明显改善.以硼化物为耐磨相的白口铸铁组织中含有硬的硼化物耐磨相和强韧的马氏体基体,具有良好的硬度和韧性组合,是一类非常具有前途的新型白口铸铁.     

双液金属复合耐磨板厚度对复合层组织和性能的影响

利用双液铸造液膜连接工艺制备大平面的低碳钢/高铬铸铁耐磨板。采用SEM,EDS对复合层进行组织观察及成分分析。结果表明:不同厚度的复合板从低碳钢侧至高铬铸铁侧可以分为低碳钢→珠光体过渡层→复合层→高铬铸铁过渡层,双金属复合层完全实现了冶金结合。通过对复合层区域进行显微硬度分析,从低碳钢至高铬铸铁侧的显微硬度在345~1260HV范围梯度分布。复合层的显微组织主要为γ-Fe+粒状碳化物。高铬铸铁过渡层奥氏体组织呈现垂直复合层方向的树枝状生长,并随着耐磨板厚度的增加,奥氏体生长的方向性逐渐消失。根据低碳钢的温度变化初步建立了相关的温度场数学模型。     

高铬铸铁耐磨材料在泥沙磨损条件下耐磨性影响因素分析

分析了碳化物形态与分布、基体组织和稀土变质处理对高铬铸铁耐磨材料在泥沙磨损条件下的耐磨性影响。结果表明：碳化物的形态和分布对高铬铸铁的耐磨性有直接影响,块状或短杆状且分布均匀的碳化物对提高材料的耐磨性有利,网状或长针状碳化物对耐磨性不利;在泥沙磨损试验条件下,提高高铬铸铁中基体组织的显微硬度和基体组织与碳化物的结合强度有利于提高高铬铸铁材料的耐磨性;稀土元素的加入,使高铬铸铁的晶粒细化,碳化物颗粒变得细小,分布更为均匀,有利于提高高铬铸铁在泥沙磨损条件下的耐磨性。     

Si影响M2高速钢中共晶碳化物的精细研究

通过金相、扫描电镜、X射线衍射、能谱分析等方法对添加不同Si量的M2高速钢中的共晶碳化物进行了精细研究。结果表明,添加1%Si后,M2高速钢铸态组织中共晶碳化物的类型和形貌都没有明显变化,仍以层片状M2C碳化物为主;添加2%和3%Si后,铸态组织中的共晶碳化物变为"鱼骨"状M6C碳化物,层片状M2C共晶碳化物已完全消失;此外,随着含Si量的增加,高速钢铸态组织枝晶间距减小。     

WC颗粒对高铬铸铁基高频感应堆焊层耐磨性的研究

通过高频感应加热技术制备添加WC颗粒的高铬铸铁基堆焊层,并对堆焊层的硬度、显微组织、物相进行表征;利用回转式磨料磨损试验机进行磨损实验。结果表明:堆焊层中主要物相为γ-Fe、(Cr,Fe)_7(C,B)_3、WC及W_2C等。实验证明,当WC含量为30%时,堆焊层具有最优的耐磨性。     

Estimation of Parameters of Universal Distribution of Moments of Failure of Products

A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling.     

Evaluation of optical properties of highly scattering media by moments of distributions of times of flight of photons

A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue.     

Estimation of potentialities of methods of summation of direct measurement errors

Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995.     

空压机轴承箱蜗壳温度探头油封改造

由于空压机进气侧轴承箱蜗壳温度探头密封效果不好,使空压机及其后续管道受到油污染。后将温度探头的O形圈密封改为骨架油封,杜绝了轴承箱漏油问题。文章简介空压机的结构和技术参数,详细介绍了骨架油封的制作和优点。     

Characteristics of mechanical properties of materials in studies of conditions of attainment of marginal states

It is shown that conditions of attainment of marginal states in the material of structural components are formulated on the basis of analysis of force and deformation criteria of formation and development of destruction. The parameters of these criteria are data on types of structural materials, standard and special characteristics of their mechanical properties, structural forms of considered elements of the equipment, and their operating stress loading. In this case, the construction of a system of state equations for describing interrelation of current damage, external actions, and responses to them is based on the concept of calculating variations in properties of materials at all stages of the design life cycle.     

Determination of parameters of microstructural inhomogeneity of deformation of metals by the method of modeling

The article suggests a method of evaluating the microstructural inhomogeneity of deformation of metals by modeling. The method includes the measurement of deformations of metal according to meshes of a dividing grid with small base and the calculation of the distribution parameters of microdeformations in model representation. It is shown that the modeling method makes it possible objectively to evaluate the microinhomogeneity of deformation of metals independently of the chosen mesh size of the dividing grid. New structural characteristics are introduced: the base and wave of variation expressing the degree of crumbling or amalgamation of metal grains by inhomogeneity of deformation.Translated from Problemy Prochnosti, No. 7, pp. 40–44, July, 1991.     

Analysis of the rate of propagation of the wave of change of boiling modes

An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate agreement is demonstrated between the derived relations and experimental data.     

水三相点复现的不确定度评定

水三相点是开尔文热力学温度的唯一基准点，也是ITS-90国际温标重要的定义固定点。因此，水三相点不确定度分析对整个温标的建立、温度量值传递起着至关重要的作用。近3年来，中国计量科学研究院研制出一系列高质量的水三相点容器，加强了水三相点的研究，为不确定度的分析提供了更为可靠的实验依据。同时，不确定度的分析也是客观评价新研制容器性能的一个重要指标。因此，根据实验结果对新研制容器所复现的水三相点进行了不确定度评定。评定结果表明，其扩展不确定度为0．16mK(k=2．69，P=0．99)。