一种高共模抑制比轨到轨全差分运算放大器

针对传统全差分运算放大器电路存在输入输出摆幅小和共模抑制比低的问题,提出了一种高共模抑制比轨到轨全差分运算放大器电路。电路的输入级采用基于电流补偿技术的互补差分输入对,实现较大的输入信号摆幅;中间级采用折叠式共源共栅结构,获得较大的增益和输出摆幅;输出级采用共模反馈环路控制的A类输出结构,同时对共模反馈环路进行密勒补偿,提高电路的共模抑制比和环路稳定性。提出的全差分运算放大器电路基于中芯国际(SMIC) 0.13μm CMOS工艺设计,结果表明,该电路在3.3 V供电电压下,负载电容为5 pF时,可实现轨到轨的输入输出信号摆幅;当输入共模电平为1.65 V时,直流增益为108.9 dB,相位裕度为77.5°,单位增益带宽为12.71 MHz;共模反馈环路增益为97.7 dB,相位裕度为71.3°;共模抑制比为237.7 dB,电源抑制比为209.6 dB,等效输入参考噪声为37.9 nV/Hz^1/2@100 kHz。     

一款基于电荷泵高压内电源的恒定跨导轨到轨运算放大器

设计了一款基于电荷泵高压内电源的恒定跨导轨到轨运算放大器.输入级采用PMOS差分对结构,通过电荷泵产生高于电源电压的输入级内电源,使运放在轨到轨输入范围能正常工作并保持输入跨导恒定.电荷泵电路所需的时钟信号通过内部振荡器电路产生,再通过电压自举电路和时序电路产生所需电平的非交叠开关控制信号,最后利用时间交织结构输出连续稳定的高压内电源.在电荷泵实现中还采用了辅助开关结合跟随运放的结构降低了主开关在切换时的毛刺.该运放在折叠式共源共栅结构中使用增益自举结构提高了总体增益,输出级采用class AB类输出结构实现轨到轨输出.该运算放大器基于0.5μm CMOS工艺完成电路与版图设计,仿真结果表明,在5 V电源电压下,直流增益为150.76 dB,单位增益带宽为53.407 MHz,相位裕度为96.1°,输入级跨导在轨到轨输入共模范围内的变化率为0.001 25%.     

一种恒跨导高增益轨到轨运算放大器

基于TSMC 0.18 μm CMOS工艺,设计了一种新颖的恒跨导高增益轨到轨运算放大器。输入级仅由NMOS管差分对构成,采用电平移位及两路复用选择器控制技术,在轨到轨共模输入范围内实现了输入级恒跨导。中间级采用折叠式共源共栅放大器结构,运算放大器能获得高增益。输出级采用前馈型AB类推挽放大器,实现轨到轨全摆幅输出。利用密勒补偿技术进行频率补偿,运算放大器工作稳定。仿真结果表明,在1.8 V电源电压下,该运算放大器的直流开环增益为129.3 dB,单位增益带宽为7.22 MHz,相位裕度为60.1°,整个轨到轨共模输入范围内跨导的变化率为1.44%。     

基于单一PMOS差分对的轨到轨输入运算放大器设计

基于国内某CMOS工艺设计了一种单一PMOS差分对的轨到轨输入、恒跨导CMOS运算放大器。输入级电路采用折叠共源共栅结构,通过体效应动态调节输入管的阈值电压扩展共模输入范围到正负电源轨,恒定共模输入范围内的跨导,自级联电流镜有源负载将差分输入转换为单端输出;输出级电路采用AB类结构实现轨到轨输出,线性跨导环确定输出管的静态偏置电流。在5 V电源电压,2.5 V共模电压,1 MΩ负载条件下,经Spectre仿真验证,该运算放大器开环增益为119 dB,相位裕度为58°,共模输入范围为0.0027～4.995 V,共模范围内跨导变化小于3%,实现了轨到轨输入共模范围内的跨导恒定。     

一种齐纳二极管控制式轨对轨CMOS运算放大器

采用0.6μm CMOS工艺,设计了一种齐纳二极管控制式轨对轨运算放大器.该运放采用了3.3V单电源供电,其输入共模范围和输出信号摆幅接近于地和电源电压,即所谓输入和输出电压范围轨对轨.该运放的小信号增益为82dB,单位增益带宽为12.34MHz,相位裕度为68°.由于电路简单,工作稳定,输入输出线性动态范围宽,非常适合于SOC芯片内集成.文中主要讨论该轨对轨运算放大器的原理,性能及设计方法,并进行了模拟仿真.     

一种轨对轨CMOS运算放大器的设计

基于0.6μmCMOS工艺,设计了一种轨对轨运算放大器。该运算放大器采用了3.3V单电源供电,其输入共模范围和输出信号摆幅接近于地和电源电压,即所谓输入和输出电压范围轨对轨。该运放的小信号增益为77dB,单位增益带宽为4.32MHz,相位裕度为79°。由于电路简单,工作稳定,输入输出线性动态范围宽,非常适合于SOC芯片内集成。     

基于单差分对输入级的新型轨到轨运算放大器设计

本文基于CMOS工艺设计了一种新型的轨到轨集成运算放大器。对比分析传统轨到轨输入级设计的优劣,该运放选择采用单差分对输入级结构,使用耗尽型NMOS管作为输入对管,利用耗尽型NMOS管的体效应以及对输入级电路结构的优化,实现轨到轨输入,以AB类输出级结构实现轨到轨输出。经过Cadence仿真验证,工作在5 V单电源供电下,共模输入电压范围可以实现满轨0～5 V,增益高达141.1 dB,带宽1.7 MHz,相位裕度55.4°,具有较低的输入失调电压264μV、输入偏置电流9 pA。整体电路实现了近乎满轨的轨到轨的输出电压摆幅,达到轨到轨运算放大器的设计要求。     

一种轨至轨输入的低压低功耗运放的设计

本文采用0.35μm的CMOS标准工艺,设计了一种轨至轨输入,静态功耗150μW,相位增益86dB,单位增益带宽2.3MHz的低压低功耗运算放大器。该运放在共模输入电平下有着几乎恒定的跨导,使频率补偿更容易实现,可应用于VLSI库单元及其相关技术领域。     

一种低电压恒定跨导轨到轨运算放大器的设计

设计了一种低电压恒定跨导的轨到轨运算放大器,作为误差放大器用在BUCK型DC-DC上实现对输出电压的调节。该运算放大器采用两级结构,输入级采用互补差分对的结构,实现了轨到轨电压的输入,并且利用2倍电流镜技术实现了跨导的恒定;输出级采用AB类放大器的结构,提高了输出电压摆幅和效率,实现了轨到轨电压的输出。该电路基于CSMC 0.25μm EN BCDMOS工艺进行设计,仿真结果表明:电源电压为2.8 V时,在输出端负载电容为160 pF、负载电阻为10 kΩ的情况下,增益为124 dB,单位增益带宽积为5.76 MHz,相位裕度为59.9℃,输入跨导为5.2 mΩ~(-1),共模抑制比为123 dB,输入共模信号范围为0～2.8V,输出电压摆幅为0～2.8 V。     

一种0.8V衬底驱动轨对轨运算放大器设计

采用衬底驱动技术设计低压低功耗轨对轨运算放大器。输入级采用衬底驱动MOSFET,有效避开阈值电压限制,将电源电压降至0.8V,实现低压下轨对轨共模输入范围。增加衬底驱动冗余差分对及反折式共源共栅求和电路实现恒定跨导控制,消除共模电压对输入级跨导的影响,输出采用前馈式AB类输出级,以提高动态输出电压范围。基于标准0.18μmCMOS工艺仿真运放,测得输出范围0.4～782.5mV,功耗48.8μW,电源抑制比58dB,CMRR65dB,直流开环增益63.8dB,单位增益带宽2.4MHz,相位裕度68°。版图设计采用双阱交叉空铅技术,面积为97.8μm×127.6μm。     

低功耗恒定跨导轨对轨运算放大器设计技术研究

为了解决轨对轨运算放大器输入级跨导随共模输入电压变化的影响,采用实时共模电压监测技术,动态跟踪轨对轨运放输入级的跨导变化,通过对偏置电流的高精度定量补偿,从而实现了对输入级跨导的恒定性控制。基于0.18μm CMOS工艺进行了具体电路的设计实现,结果表明:在电源电压3.3 V、负载电阻100Ω、负载电容1 nF的条件下,运放增益为148 dB、相位裕度为61°、功耗为39.6μW,共模输入范围高达0~3.3 V,输入级跨导变化率仅为2.1%。     

Some Design Aspects of a Two-Stage Rail-to-Rail CMOS Op Amp

A two-stage low-voltage CMOS op amp with rail-to-rail input and output voltage ranges is presented. The circuit uses complementary differential input pairs to achieve the rail-to-rail common-mode input voltage range. The differential pairs operate in strong inversion, and the constant transconductance is obtained by keeping the sum of the square roots of the tail currents constant. Such an input stage has an offset voltage which depends on the common input voltage level, resulting in a poor common-mode rejection ratio. Therefore, special attention has been given to the reduction of the op amp's systematic offset voltage. Gain-boost amplifiers are connected in a special way to provide not only an increase of the low-frequency open-loop gain, but also to provide a significant reduction of the systematic offset voltage.     

0.9 V rail-to-rail constant gm CMOS amplifier input stage

Presented is a 0.9 V rail-to-rail constant g_m CMOS amplifier input stage consisting of complementary differential pairs and a g_m control circuit. The g_m control circuit eliminates the g_m dead zone, which occurs in the conventional rail-to-rail amplifier with ultra-low supply voltages. The proposed amplifier input stage has a constant g_m that varies by ±2.3% for rail-to-rail input common-mode levels. To verify the proposed amplifier design, an experimental prototype operational amplifier is also implemented using 0.35 mm standard CMOS technology.     

低功耗轨至轨CMOS运算放大器设计

设计了一个1.5 V低功耗轨至轨CMOS运算放大器。电路设计中为了使输入共模电压范围达到轨至轨性能,采用了NMOS管和PMOS管并联的互补差动对输入结构,并采用成比例的电流镜技术实现了输入级跨导的恒定。在中间增益级设计中,采用了适合在低压工作的低压宽摆幅共源共栅结构;在输出级设计时,为了提高效率,采用了简单的推挽共源级放大器作为输出级,使得输出电压摆幅基本上达到了轨至轨。当接100 pF电容负载和1 kΩ电阻负载时,运放的静态功耗只有290μW,直流开环增益约为76 dB,相位裕度约为69°,单位增益带宽约为1 MHz。     

一种恒跨导轨对轨CMOS运算放大器的设计

设计了一种新颖的恒跨导轨对轨CMOS运算放大器结构。输入级采用轨对轨的结构,在输入级采用4个虚拟差分对管来对输入差分对的电流进行限制,使运放的输入级跨导在工作范围内保持恒定。输出级采用前馈式AB类输出结构,以使输出达到全摆幅。仿真结果显示,在5 V电源电压和带有10 pF电容与10 kΩ电阻并联的负载下,该运放在共模输入范围内实现了恒跨导,在整个共模输入范围内跨导变化率仅为3%,输出摆幅也达到了轨对轨全摆幅,运放的开环增益为108.5 dB,增益带宽积为26.7 MHz,相位裕度为76.3°。     

Current mode instrumentation amplifier with rail-to-rail input and output

This paper presents the results from an investigation on the implementation of Current Mode Instrumentation Amplifiers (CMIAs) with rail-to-rail operational amplifiers (op amp) with a gm control circuit. The objective of employing rail-to-rail op amps in the implementation of a CMIA is the improvement of the common-mode operation range. The enhancement of the input common mode range (ICMR) is obtained using op amps with a rail-to-rail input stage followed by a cascode-based output stage. A prototype of the CMIA was implemented in standard 0.6 μm XFAB CMOS technology. Test results showed that the CMIA common mode range was extended but with moderated CMRR. To minimize this issue the amplifier was re-designed and sent to fabrication. Simulations with the components variations included were performed and showed the enhancement of the CMRR can be expected.     

A Low-Voltage Fully Differential Constant-Gm Rail-to-Rail CMOS Operational Amplifier

A low-voltage fully differential CMOS operational amplifier withconstant-g_mand rail-to-rail input and output stages ispresented. It is the fully differential version of a previously realizedsingle-ended operational amplifier where a novel circuit to ensure constanttransconductance has been implemented [1]. The input stage is a rail-to-railstructure formed by two symmetrical OTAs in parallel (the input transistorsare operating in weak inversion). The class-AB output stages have also afull voltage swing. A rail-to-rail input common mode feedback structureallows the output voltage control. Measurements in a 0.7 µ standardCMOS process with threshold voltages of about 0.7 V have been done. Theminimum experimental supply voltage is about 1.1 V. The circuit provides a60 dB low frequency voltage gain and about 1.5 MHz unity gain frequency fora total power consumption of about 0.72 mW at a 1.5 V supply voltage.     

一种电流跟踪补偿的输入输出全摆幅运算放大器

介绍了一种工作在2.5V电压下、具有全摆幅输入与输出功能的两级CMOS运算放大器。通过一种简单有效的电流跟踪电路实现了输入跨导恒定的要求，这样使得频率补偿变得容易实现；为了降低功耗，输入级工作在弱反型区：输出级采用带有前馈控制电路的AB类输出电路，实现了输出信号的轨至轨。电路具有结构简单、功耗低、面积小、性能高等优点。     

1-V rail-to-rail operational amplifiers in standard CMOS technology

The constraints on the design of CMOS operational amplifiers with rail-to-rail input range for extremely low supply voltage operation, are addressed. Two design approaches for amplifiers based on complementary input differential pairs and a single input pair, respectively, are presented. The first realizes a feedforward action to accommodate the common-mode (CM) component of the input signals to the amplifier input range. The second approach performs a negative feedback action over the input CM signal. Two operational amplifiers based on the proposed approaches have been designed for 1-V total supply operation, and fabricated in a standard 1.2-μm CMOS process. Experimental results are provided and the corresponding performances are discussed and compared     

An adaptive biasing one-stage CMOS operational amplifier fordriving high capacitive loads

An adaptive biasing one-stage CMOS operational amplifier for driving high capacitive loads has been developed. The amplifier has been designed to drive liquid-crystal-displays (LCDs) in battery-supplied devices. Contradictory features like low power dissipation and high driving capability at low supply voltage are required. Complementary differential input stages provide rail-to-rail common-mode input range. With a special cross-coupled double-to-single-end conversion, a full supply output range is achieved. These improvements solve a functional problem of some existing adaptive biasing amplifiers. Simulation and measurements demonstrate good correlation and show the expected results, especially in the critical operating area