Techno-economic evaluation of hydrogen refueling stations with liquid or gaseous stored hydrogen

In this study, different hydrogen refueling station (HRS) architectures are analyzed energetically as well as economically for 2015 and 2050. For the energetic evaluation, the model published in Bauer et al. [1] is used and norm-fitting fuelings according to SAE J2601 [2] are applied. This model is extended to include an economic evaluation. The compressor (gaseous hydrogen) resp. pump (liquid hydrogen) throughput and maximum pressures and volumes of the cascaded high-pressure storage system vessels are dimensioned in a way to minimize lifecycle costs, including depreciation, capital commitment and electricity costs. Various station capacity sizes are derived and energy consumption is calculated for different ambient temperatures and different station utilizations. Investment costs and costs per fueling mass are calculated based on different station utilizations and an ambient temperature of +12 °C. In case of gaseous trucked-in hydrogen, a comparison between 5 MPa and 20 MPa low-pressure storage is conducted. For all station configurations and sizes, a medium-voltage grid connection is applied if the power load exceeds a certain limit. For stations with on-site production, the electric power load of the hydrogen production device (electrolyzer or gas reformer) is taken into account in terms of power load. Costs and energy consumption attributed to the production device are not considered in this study due to comparability to other station concepts. Therefore, grid connection costs are allocated to the fueling station part excluding the production device. The operational strategy of the production device is also considered as energy consumption of the subsequent compressor or pump and the required low-pressure storage are affected by it. All station concepts, liquid truck-supplied hydrogen as well as stations with gaseous truck-supplied or on-site produced hydrogen show a considerable cost reduction potential. Long-term specific hydrogen costs of large stations (6 dispensers) are 0.63 €/kg – 0.76 €/kg (dependent on configuration) for stations with gaseous stored hydrogen and 0.18 €/kg for stations with liquid stored hydrogen. The study focuses only on the refueling station and does not allow a statement about the overall cost-effectiveness of different pathways.     

Energetic evaluation of hydrogen refueling stations with liquid or gaseous stored hydrogen

The future success of fuel cell electric vehicles requires a corresponding infrastructure. In this study, two different refueling station concepts for fuel cell passenger cars with 70 MPa technology were evaluated energetically. In the first option, the input of the refueling station is gaseous hydrogen which is compressed to final pressure, remaining in gaseous state. In the second option, the input is liquid hydrogen which is cryo-compressed directly from the liquid phase to the target pressure. In the first case, the target temperature of −33 °C to −40 °C [1] is achieved by cooling down. In the second option, gaseous deep-cold hydrogen coming from the pump is heated up to target temperature. A dynamic simulation model considering real gas behavior to evaluate both types of fueling stations from an energetic perspective was created. The dynamic model allows the simulation of boil-off losses (liquid stations) and standby energy losses caused by the precooling system (gaseous station) dependent on fueling profiles. The functionality of the model was demonstrated with a sequence of three refueling processes within a short time period (high station utilization). The liquid station consumed 0.37 kWh/kg compared to 2.43 kWh/kg of the gaseous station. Rough estimations indicated that the energy consumption of the entire pathway is higher for liquid hydrogen. The analysis showed the high influence of the high-pressure storage system design on the energy consumption of the station. For future research work the refueling station model can be applied to analyze the energy consumption dependent on factors like utilization, component sizing and ambient temperature.     

Performance of a hydrogen refueling station in the early years of commercial fuel cell vehicle deployment

Since 2003, the National Fuel Cell Research Center at the University of California, Irvine (UCI) has operated the first U.S. publicly accessible hydrogen refueling station (HRS). During this period, the UCI HRS supported all manufacturers in the early, pre-commercialization years of the fuel cell electric vehicle (FCEV). This paper describes and analyzes the performance of the UCI HRS during the first five years of FCEV commercialization, over which time the station has dispensed the most hydrogen daily in the California network. The station performance is compared to aggregate data published by NREL for all U.S. HRSs. Using the Hydrogen Delivery Scenario Analysis Model, typical daily refueling profiles are analyzed to determine the effect on HRS design. The results show different daily refueling profiles could substantially affect HRS design and ultimately the cost of hydrogen. While technical issues have been reduced, the compressor, dispenser, and fueling rate are areas for improvement.     

Optimization of the overall energy consumption in cascade fueling stations for hydrogen vehicles

Hydrogen fueling stations are emerging around and in larger cities in Europe and United States together with a number of hydrogen vehicles. The most stations comply with the refueling protocol made by society of automotive engineers and they use a cascade fueling system on-site for filling the vehicles. The cascade system at the station has to be refueled as the tank sizes are limited by the high pressures. The process of filling a vehicle and afterward bringing the tanks in refueling station back to same pressures, are called a complete refueling cycle. This study analyzes power consumption of refueling stations as a function of number of tanks, volume of the tanks and the pressure in the tanks. This is done for a complete refueling cycle. It is found that the energy consumption decreases with the number of tanks approaching an exponential function. The compressor accounts for app. 50% of the energy consumption. Going from one tank to three tanks gives an energy saving of app. 30%. Adding more than four tanks the energy saving per extra added tank is less than 4%. The optimal numbers of tanks in the cascade system are three or four.     

Enhancement of hydrogen storage performance in shell and tube metal hydride tank for fuel cell electric forklift

Novel metal hydride (MH) hydrogen storage tanks for fuel cell electric forklifts have been presented in this paper. The tanks comprise a shell side equipped with 6 baffles and a tube side filled with 120 kg AB₅ alloy and 10 copper fins. The alloy manufactured by vacuum induction melting has good hydrogen storage performance, with high storage capacity of 1.6 wt% and low equilibrium pressure of 4 MPa at ambient temperature. Two types of copper fins, including disk fins and corrugated fins, and three kinds of baffles, including segmental baffles, diagonal baffles and hole baffles, were applied to enhance the heat transfer in metal hydride tanks. We used the finite element method to simulate the hydrogen refueling process in MH tanks. It was found that the optimized tank with corrugated fins only took 630 s to reach 1.5 wt% saturation level. The intensification on the tube side of tanks is an effective method to improve hydrogen storage performance. Moreover, the shell side flow field and hydrogen refueling time in MH tanks with different baffles were compared, and the simulated refueling time is in good agreement with the experimental data. The metal hydride tank with diagonal baffles shows the shortest hydrogen refueling time because of the highest velocity of cooling water. Finally, correlations regarding the effect of cooling water flow rate on the refueling time in metal hydride tanks were proposed for future industrial design.     

Improving chiller performance and energy efficiency in hydrogen station operation by tuning the auxiliary cooling

In a hydrogen station that operates with direct fueling through the use of a 700 bar boost compressor, the outlet hydrogen temperature can significantly increase, stressing the chiller system. This paper evaluates improvements that can be made to the auxiliary cooling system integrated with the compressor. Both theoretical modeling and experiments were performed at Cal State LA Hydrogen Research and Fueling Facility. The findings suggest that adjusting the auxiliary closed-loop cooling system from 15 °C to 10 °C reduced the station energy consumption and decreased the demand on the station chiller that needed to provide ?20 °C hydrogen at the hose. The overall energy consumption for a single fueling reduced by between 2.86 and 9.43% for the set of experiments conducted. After the temperature of the closed-loop cooling system was reduced by 5 °C, the boost compressor outlet temperature dropped from 46-50 °C–40 °C and consequently at the hose the hydrogen temperature declined by 3 °C. Results were scaled up with a forecast on the number of daily refueling events. With a low number of daily fuelings, the proposed set-up showed a minor influence on the overall station energy consumption. However, the benefits were more pronounced for a connector station with sales at 180 kg/day, where the energy efficiency improved by between 1.4 and 5.5%, and even more so for a higher capacity station at 360 kg/day, where the improvement was between 2.9 and 8%.     

Hydrogen refueling stations and fuel cell buses four year operational analysis under real-world conditions

Worldwide about 550 hydrogen refueling stations (HRS) were in operation in 2021, of which 38% were in Europe. With their number expected to grow even further, the collection and investigation of real-world station operative data are fundamental to tracking their activity in terms of safety issues, performances, maintenance, reliability, and energy use. This paper analyses the parameters that characterize the refueling of 350 bar fuel cell buses (FCB) in five HRS within the 3Emotion project. The HRS are characterized by different refueling capacities, hydrogen supply schemes, storage volumes and pressures, and operational strategies. The FCB operate over various duty cycles circulating on urban and extra-urban routes. From data logs provided by the operators, a dataset of four years of operation has been created. The results show a similar hydrogen amount per fill distribution but quite different refueling times among the stations. The average daily mass per bus and refueling time are around 14.62 kg and 10.28 min. About 50% of the total amount of hydrogen is dispensed overnight, and the refueling events per bus are typically every 24 h. On average, the buses' time spent in service is 10 h per day. The hydrogen consumption is approximately 7 kg/100 km, a rather effective result reached by the technology. The station utilization is below 30% for all sites, the buses availability hardly exceeds 80%.     

Less is more: Robust prediction for fueling processes on hydrogen refueling stations

The monitoring of hydrogen refueling stations (HRSs) ensures the safety of their operations as well as optimal fueling performance. For a H70-T40 dispenser, a fueling process is required to control the temperature to be below 85 °C; the pressure to be under 70 MPa; and the final state-of-charge (SOC) to be between 95% and 100%. Table-based or MC (total heat capacity) formula-based fueling protocols are traditionally used to achieve such control. In this paper, we propose using a machine learning model to predict the key parameters of fueling processes: the final SOC, the final temperature, and the final pressure in the vehicle tank. To handle outliers and noise in real operation, we adopt a two-stage method. In the first stage, after clustering fueling processes using soft dynamic time warping, a small number of fueling processes are selected from a large amount of historical data. In the second stage, based on initial and current operating conditions, the final SOC, temperature, and pressure of fueling processes are predicted using three models: least absolute shrinkage and selection operator (LASSO), Gaussian process regression (GPR), and robust regression. The experiments on real operational data collected from four hydrogen refueling stations show that the robust regression model achieves better performance than LASSO and GPR for three out of the four stations, and that the robust regression model captures the normal states of regular operation. The computational time of the robust regression model is also scalable for real-time operation. Our study provides a feasible machine learning model for predicting the key fueling parameters, which facilitates the optimization of HRS operation.     

Single-tank storage versus multi-tank cascade system in hydrogen refueling stations for fuel cell buses

Many countries in Europe are investing in fuel cell bus technology with the expected mobilization of more than 1200 buses across Europe in the following years. The scaling-up will make indispensable a more effective design and management of hydrogen refueling stations to improve the refueling phase in terms of refueling time and dispensed quantity while containing the investment and operation costs. In the present study, a previously developed dynamic lumped model of a hydrogen refueling process, developed in MATLAB, is used to analyze tank-to-tank fuel cell buses (30–40 kg_H2 at 350 bar) refueling operations comparing a single-tank storage with a multi-tank cascade system. The new-built Aalborg (DK) hydrogen refueling station serves as a case study for the cascade design. In general, a cascading refueling approach from multiple storage tanks at different pressure levels provides the opportunity for a more optimized management of the station storage, reducing the pressure differential between the refueling and refueled tanks throughout the whole refueling process, thus reducing compression energy. This study demonstrates the validity of these aspects for heavy-duty applications through the technical evaluation of the refueling time, gas heating, compression energy consumption and hydrogen utilization, filling the literature gap on cascade versus single tank refueling comparison. Furthermore, a simplified calculation of the capital and operating expenditures is conducted, denoting the cost-effectiveness of the cascade configuration under study. Finally, the effect of different pressure switching points between the storage tanks is investigated, showing that a lower medium pressure usage reduces the compression energy consumption and increases the station flexibility.     

Quantitative analysis of a successful public hydrogen station

Reliable hydrogen fueling stations will be required for the successful commercialization of fuel cell vehicles. An evolving hydrogen fueling station has been in operation in Irvine, California since 2003, with nearly five years of operation in its current form. The usage of the station has increased from just 1000 kg dispensed in 2007 to over 8000 kg dispensed in 2011 due to greater numbers of fuel cell vehicles in the area. The station regularly operates beyond its design capacity of 25 kg/day and enables fuel cell vehicles to exceed future carbon reduction goals today. Current limitations include a cost of hydrogen of $15 per kg, net electrical consumption of 5 kWh per kg dispensed, and a need for faster back-to-back vehicle refueling.     

Numerical investigation of the vortex tube performance in novel precooling methods in the hydrogen fueling station

In the present study, the potential of integrating a Ranque-Hilsch vortex tube (RHVT) in the precooling process for refueling high-pressure hydrogen vehicles in hydrogen refueling stations is investigated. In this regard, two novel precooling processes integrating a vortex tube are proposed to significantly reduce the capital expenditure and operating costs in hydrogen fueling stations. Then a numerical study of the RHVT performance is carried out for a high-pressure hydrogen flow to validate the feasibility of the proposed processes. Obtained results from the numerical simulation show that the energy separation effect also exists in the RHVT with hydrogen flow at the pressure level of tens of megapascals. Moreover, it is found that the energy separation performance of the RHVT improves as the pressure ratio increases. In other words, the temperature drop of the cold exit of RHVT decreases as the pressure ratio decreases in the refueling process, which just matches the slowing-down temperature rise during the cylinder charge. Based on the obtained results, it is concluded that the integration of a RHVT into the precooling process has potential in the hydrogen fueling station.     

Tube-trailer consolidation strategy for reducing hydrogen refueling station costs

The rollout of hydrogen fuel cell electric vehicles (FCEVs) requires the initial deployment of an adequate network of hydrogen refueling stations (HRSs). Such deployment has proven to be challenging because of the high initial capital investment, the risk associated with such an investment, and the underutilization of HRSs in early FCEV markets. Because the compression system at an HRS represents about half of the station's initial capital cost, novel concepts that would reduce the cost of compression are needed. Argonne National Laboratory with support from the U.S. Department of Energy's (DOE) Fuel Cell Technologies Office (FCTO) has evaluated the potential for delivering hydrogen in high-pressure tube-trailers as a way of reducing HRS compression and capital costs. This paper describes a consolidation strategy for a high-pressure (250-bar) tube-trailer capable of reducing the compression cost at an HRS by about 60% and the station's initial capital investment by about 40%. The consolidation of tube-trailers at pressures higher than 250 bar (e.g., 500 bar) can offer even greater HRS cost-reduction benefits. For a typical hourly fueling-demand profile and for a given compression capacity, consolidating hydrogen within the pressure vessels of a tube-trailer can triple the station's capacity for fueling FCEVs. The high-pressure tube-trailer consolidation concept could play a major role in enabling the early, widespread deployment of HRSs because it lowers the required HRS capital investment and distributes the investment risk among the market segments of hydrogen production, delivery, and refueling.     

加氢站流程和配置技术现状与展望

加氢站（HRS）是氢能高效利用的重要环节,是促进燃料电池汽车行业发展的重要基础设施。本文介绍了外供氢加氢站一般系统流程及配置方法;整理了国内外关于系统流程的优化措施,其中包括常规系统的部件（如长管拖车、站侧储罐配置及预冷系统）的配置优化,以及非常规部件的新型系统（如喷射器、涡流管或膨胀机）的集成;最后对未来优化方向进行了展望。     

Risk assessment of Hydrogen fueling stations for 70 MPa FCVs

People are placing their hopes on the future of fuel-cell vehicles (FCVs) to replace today's gasoline-fueled vehicles. To encourage the widespread use of FCVs, however, these vehicles must be able to drive a distance of at least 500 km, mileage comparable to today's gasoline-fueled vehicles. To achieve this distance, automobile manufacturers are focusing their efforts on developing new hydrogen fuel tanks that will raise pressure to 70 MPa from the current 35 MPa. At the same time, hydrogen stations will also have to be able to provide 70 MPa compressed hydrogen gas to service these improved FCVs. Regulations for hydrogen fueling stations where pressure is no higher than 40 MPa were established in 2005 in Japan but it goes without saying that these regulations are inadequate for hydrogen fueling stations of 70 MPa.     

Modeling operating modes,energy consumptions,and infrastructure requirements of fuel cell plug in hybrid electric vehicles using longitudinal geographical transportation data

The fuel cell plug in hybrid electric vehicle (FCPHEV) is a near-term realizable concept to commercialize hydrogen fuel cell vehicles (FCV). Relative to conventional FCVs, FCPHEVs seek to achieve fuel economy benefits through the displacement of hydrogen energy with grid-sourced electrical energy, and they may have less dependence on a sparse hydrogen fueling infrastructure. Through the simulation of almost 690,000 FCPHEV trips using geographic information system (GIS) data surveyed from a fleet of private vehicles in the Puget Sound area of Washington State, USA, this study derives the electrical and hydrogen energy consumption of various design and control variants of FCPHEVs. Results demonstrate that FCPHEVs can realize hydrogen fuel consumption reductions relative to conventional FCV technologies, and that the fuel consumption reductions increase with increased charge depleting range. In addition, this study quantifies the degree to which FCPHEVs are less dependent on hydrogen fueling infrastructure, as FCPHEVs can refuel with hydrogen at a lower rate than FCVs. Reductions in hydrogen refueling infrastructure dependence vary with control strategies and vehicle charge depleting range, but reductions in fleet-level refueling events of 93% can be realized for FCPHEVs with 40 miles (60 km) of charge depleting range. These fueling events occur on or near the network of highways at approximately 4% of the rate (refuelings per year) of that for conventional FCVs. These results demonstrate that FCPHEVs are a type of FCV that can enable an effective and concentrated hydrogen refueling network.     

Review on equipment configuration and operation process optimization of hydrogen refueling station

The construction of hydrogenation infrastructure is important to promote the large-scale development of hydrogen energy industry. The technical performance of hydrogen refueling station (HRS) largely determines the refueling efficiency and cost of hydrogen fuel cell vehicles. This paper systematically lists the hydrogen refueling process and the key equipment applicable in the HRS. It comprehensively reviews the key equipment configuration from the hydrogen supply, compression, storage and refueling of the HRS. On the basis of the parameter selection and quantity configuration method, the process optimization technology related to the equipment utilization efficiency and construction cost was quantitatively evaluated. Besides, the existing problems and prospects are put forward, which lays the foundation for further research on the technical economy of HRSs.     

Solar powered residential hydrogen fueling station

This paper presents a conceptual design of a solar powered hydrogen fueling station for a single family home in Wallingford, Connecticut, USA. Sixty high-efficiency monocrystalline silicon photovoltaic (PV) solar panels (Total capacity: 18.9 kW) account for approximately 94.7% of the hydrogen home’s power consumption. The fueling station consists of a 165 bar high pressure electrolyzer for on-site production of 2.24 kg/day of hydrogen, three-bank cascade configuration storage tanks (4.26 kg of H₂ at 350 bar) and a SAE J2600 compliant hydrogen nozzle. The system produces 0.8 kg/day of hydrogen for a fuel cell vehicle with an average commute of 56 km/day (Fuel mileage: 71 km/kg H₂). Safety codes and standards applicable at the facility are described, and a well-to-wheel analysis is performed to contrast the carbon dioxide emissions of conventional gasoline and fuel cell vehicles. The energy efficiency obtained by incorporating a solar-hydrogen system for residential applications is also computed.     

Market penetration analysis of fuel cell vehicles in Japan by using the energy system model MARKAL

The objective of the present work is to validate the hydrogen energy roadmap of Japan by analyzing the market penetration of fuel cell vehicles (FCVs) and the effects of a carbon tax using an energy system model of Japan based on MARKAL. The results of the analysis show that a hydrogen FCV would not be cost competitive until 2050 without a more severe carbon tax than the government's planned 2400 JPY/t-C carbon tax. However, as the carbon tax rate increases, instead of conventional vehicles including the gasoline hybrid electric vehicle, hydrogen FCVs gain market penetration earlier and more. By assuming a more severe carbon tax rate, such as 10 000 JPY/t-C, the market share of hydrogen FCVs approaches the governmental goal. This suggests that cheaper vehicle cost and hydrogen cost than those targeted in the roadmap should be attained or subsidies to hydrogen FCV and hydrogen refueling station will be necessary for achieving the goal of earlier market penetration.     

Improving hydrogen refueling stations to achieve minimum refueling costs for small bus fleets

Fuel cell vehicles using green hydrogen as fuel can contribute to the mitigation of climate change. The increasing utilization of those vehicles creates the need for cost efficient hydrogen refueling stations. This study investigates how to build the most cost efficient refueling stations to fuel small fleet sizes of 2, 4, 8, 16 and 32 fuel cell busses. A detailed physical model of a hydrogen refueling station was built to determine the necessary hydrogen storage size as well as energy demand for compression and precooling of hydrogen. These results are used to determine the refueling costs for different station configurations that vary the number of storage banks, their volume and compressor capacity.It was found that increasing the number of storage banks will decrease the necessary total station storage volume as well as energy demand for compression and precooling. However, the benefit of adding storage banks decreases with each additional bank. Hence the cost for piping and instrumentation to add banks starts to outweigh the benefits when too many banks are used. Investigating the influence of the compressor mass flow found that when fueling fleets of 2 or 4 busses the lowest cost can be reached by using a compressor with the minimal mass flow necessary to refill all storage banks within 24 h. For fleets of 8, 16 and 32 busses, using the compressor with the maximum investigated mass flow of 54 kg/h leads to the lowest costs.     

H2 refueling assessment of composite storage tank for fuel cell vehicle

Hydrogen as compressed gas is a promising option for zero-emission fuel cell vehicle. The fast and efficient refueling of high pressure hydrogen can provide a convenient platform for fuel cell vehicles to compete with conventional gasoline vehicles. This paper reports the finding of adiabatic simulation of the refueling process for Type IV tank at nominal working pressure of 70 MPa with considering the station refueling conditions. The overall heat transfer involved in refueling process was investigated by heat capacity model based on MC method defined by SAE J2601. The simulation results are validated against experimental data of European Commission's Gas Tank Testing Facility at Joint Research Centre (GasTef JRC), Netherlands. The results confirmed that end temperature and state of charge significantly depends on refueling parameters mainly supply hydrogen temperature and filling rate.