气液固微型流化床的气液传质系数

气液固微型流化床兼具微流控系统和宏观流化床的优点,具有潜在的工业应用价值,但是,其应用基础研究十分缺乏。采用床径为1.6、2.0、2.4 mm的微型流化床,平均粒径为160、190、220 μm的玻璃珠,以NaOH水溶液吸收CO₂气体为气液传质研究物系,在三相流动研究的基础上,考察了表观气速、表观液速、床径、粒径等对三相微型流化床气液体积传质系数的影响。结果表明：给定其他条件,增加表观气速和表观液速,均使气液体积传质系数增大;表观气速主要改变气含率和气液相界面积,而表观液速主要改变液相传质系数;床径减小,气液相界面积和气液体积传质系数都有所增加;在气液两相微型鼓泡塔中加入固体颗粒,形成三相分散鼓泡流型,当其固含率在0.15~0.30范围内,可显著增强气液传质,其气液体积传质系数是气液微鼓泡塔的1.1~1.5倍;与宏观流化床相比,相同条件下微型床的相界面积为它的5~10倍,是微型流化床具有更大体积传质系数的主要影响因素。     

三相循环流化床中的气液相界面积和传质系数

采用溶氧法测量了三相循环流化床中液相溶氧浓度的轴向分布,并按轴向扩散模型处理实验数据,优化得到气液体积传质系数kLa,同时用光纤探头测量了体系中的气含率和气泡大小分布,计算得到了气液相界面积a和气液传质系数kL,并研究了主要操作条件(表观气速、表观液速和固含率)对气液传质系数的影响规律.     

高温高压下浆态鼓泡床气液传质系数的测定

采用气体动态吸收法,对高温高压下浆态鼓泡床中气液传质系数进行了测定,考察了系统压力、温度、表观气速及固含量等操作条件对传质系数的影响. 结果表明,在温度298~473 K、气体压力1.0~3.0 MPa、表观气速0.03~0.10 m/s、固含量0%~20%(w)的实验条件下,体积传质系数随着压力、温度及表观气速的增加而增大,随固含量的增加而减小. 同时对不同塔径的传质系数进行了比较,表明在相同的操作条件下,大塔的传质系数略高于小塔.     

液固和气液固微型流态化研究进展

在百年流态化的研究过程中,涉及到直径不同的流化床。但是,多以流化床的大型化为研究目标,对微型流化床及其本身特性的研究很少。作为专门处理固体颗粒的流态化单元过程,其装置的微型化将兼具微通道反应器和宏观流化床各自的优点,是流态化研究的重要方向。鉴于气固微型流化床已有全面的国内外进展综述,本文仅对液固和气液固微型流化床的国内外研究进展进行分析。结论性内容包括：液固微型流化床床径减小,壁面效应增强,最小流化液速实验值大于Ergun公式计算值;需对描述液固均匀膨胀流化规律的Richardson-Zaki方程加以修正。气液固微型流化床内存在4种典型流型：半流化、弹状流、分散鼓泡流和液体输送流;由于床径减小,出现半流化状态,依据压降表观液速关系曲线等无法确定最小流化液速;气液固微型流化床的反应性能得以有效提升;最后给出了进一步研究的方向,以期为后续研究提供参考。     

气液固三相环流反应器的研究进展

综述了气液固三相环流反应器的类型及工作原理、气液固三相环流反应器的特性参数(气含率、固含率、循环液速、液相体积传质系数、轴向分散系数)的测量方法和影响因素，介绍了特性参数的数学模型。并对现有模型进行了评述。对今后的研究提出一些建议。     

小型气-液-固流化床液相的停留时间分布

采用脉冲示踪技术,研究了3 mm床径的小型气-液-固流化床内液相停留时间分布。以KCl为示踪剂,液相为去离子水,气相为空气,固相为平均粒径0.123~0.222 mm的玻璃微珠和氧化铝颗粒,测量流化床出口液相的电导率,得到其停留时间分布曲线。结果表明,增大表观液速和表观气速,分布曲线变窄,平均停留时间缩短,Peclet数增大;固相的存在使液相的平均停留时间增长。表观液速1.96~15.70 mm×s^-1,表观气速1.18~1.96 mm×s^-1的条件下,流动接近层流;平均停留时间的范围为（19.6±0.34）s~（48.0±0.92）s,建立的Pe经验关联式对实验结果有较好的预测,偏差在±25%以内。研究结果对于小型三相流化床的设计放大具有指导意义。     

喷嘴结构对射流鼓泡反应器混合和传质性能的影响

喷嘴结构对射流鼓泡反应器的混合和传质性能具有重要的影响。以空气-水作为模拟介质,使用双探头电导探针、电解质示踪法和动态溶氧法,对比研究了缩径式圆形喷嘴和旋扭三角形喷嘴对射流鼓泡反应器中气泡尺寸分布、平均气含率、液相混合时间和气液传质系数的影响规律。实验发现,随着气速或液体射流Reynolds数的增大,两种喷嘴对应的平均气含率、液相混合时间和气液传质系数具有相同的变化规律;与缩径式圆形喷嘴相比,采用旋扭三角形喷嘴的射流鼓泡反应器中气泡尺寸更小,平均气含率更高,宏观混合时间更短;当气体输入功占总输入功比例超过20%时,喷嘴结构对气液传质系数的影响较小,当气体输入功占总输入功比例小于20%时,旋扭三角形喷嘴的气液传质性能优于缩径式圆形喷嘴。研究结果可为工业射流鼓泡反应器喷嘴结构的优化提供理论指导。     

鼓泡床反应器内流动与传质行为的研究进展

总结了有关浆态鼓泡床反应器内流动、混合用气液传质特性的研究成果,详细地介绍了鼓泡床反应器内气含率、液速、液体轴向扩散系数、传质系数的测量方法,阐述了鼓泡床反应器性能的主要影响因素,如系统压力、温度、气体表观气速、液体性质及固含率等对流动、液相混合和传质特性的影响,并对鼓泡床反应器的应用前景进行了详述.     

微量醇及电解质强化气液传质的研究

在气升式内环流反应器中考察了微量醇类物质(乙醇、叔丁醇、季戊四醇)及电解质(CaCl2)对氧的液相体积传质系数和气含率的影响。结果表明,向空气-水体系中添加微量醇类物质可以明显改善气液传质性能,同时醇类物质强化气-液传质存在一极限浓度,超过此浓度后,氧的液相体积传质系数略有降低;当表观气速增加时,去离子水体系和含醇体系的气含率都增加,但醇体系的气含率明显高于去离子水体系。此外,添加电解质CaCl2也会使氧的液相体积传质系数有所提高,并从离子强度的角度对其抑制气泡聚并的机理进行了分析。     

上流式反应器气液相间传质特性的实验研究

上流式反应器设置在固定床渣油加氢反应器前有利于提高渣油原料适用性,延长装置运行时间。实验研究了上流式反应器气液相间传质,采用五齿柱形氧化铝催化剂模拟工业催化剂颗粒,水溶液模拟渣油,空气模拟氢气,采用无氧水物理吸收和亚硫酸钠化学吸收的方法,测定了在高气液比的条件下上流式反应器床层气液相间传质特性实验。考察了表观气速、表观液速、填料粒径、内构件、催化剂级配和床层高径比对液相体积传质系数和气液相界比表面积的影响规律。实验数据表明,液相体积传质系数随着气、液速的增大而增大;随填料颗粒增大而减小;在床层内安装合适的内构件或增大反应器高径比,能够促进气液相间传质。基于实验数据拟合了适合上流式反应器液相体积传质系数和气液相界比表面积的经验关联式,拟合误差最大分别为12%和24%;表明所建气液相间传质的经验关联式能更好地预测上流式反应器中的气液相间传质特性。     

HYDRODYNAMICS, MIXING AND MASS TRANSFER IN A LARGE DIAMETER JET BUBBLE COLUMN

Experimental measurements for the axial and radial variations in gas holdup, axial and radial dispersion coefficients, volumetric gas-liquid mass transfer coefficient and liquid phase circulation velocity in a cone of a large diameter (122 cm) jet bubble column are presented. Two diameters of the inlet nozzle, namely 10.16 cm and 15.24 cm, three superficial gas velocities (based on cylinder diameter), 3 cm/sec, 6 cm/sec and 8 cm/sec and two superficial liquid velocities, 0.3 cm/sec and 0.6 cm/sec, are examined. The experimental data are obtained for two different bed heights.

The experimental data showed significant axial and radial variations in the gas holdup. The volumetric average gas holdup was higher at higher gas velocity and larger nozzle diameter and somewhat higher at lower liquid velocity. The axial dispersion was high while the radial dispersion was low. The volumetric gas-liquid mass transfer coefficient was larger at higher gas velocity and larger nozzle diameter. The liquid recirculation begins only at the upper end of the cone. In general, experimental data indicate that a jet bubble column provides a high degree of mixing and transport rates.     

Flow regimes and mass transfer in counter-current bubble columns

Counter current bubble columns have the feature that specific gas-liquid interfacial area and gas holdup are larger than those for standard and cocurrent bubble columns. In this study, three different flow regimes, churn-turbulent flow, bubble flow and bubble down-flow, have been observed in a counter-current bubble column and correlations of gas holdup and volumetric liquid-phase mass transfer coefficient have been proposed as functions of operating variables such as the superficial velocities of gas and liquid, the gas-liquid slip velocity and the liquid properties.     

气升式外环流反应器的体积传质系数

以Higbie的渗透理论和Kolmogoroff的湍流理论为基础,提出了计算液体旋涡在气液相界面暴露时间的方法,并建立了预测体积传质系数的模型方程。在不同管径比下的外环流反应器中,对空气 水体系测定了操作气速对体积传质系数、循环液速和气含率的影响。将体积传质系数与表观气速和下降管与上升管的面积比按幂函数进行关联,其预测值和试验值符合较好。     

A highly elevated mass transfer rate process for three-phase,liquid-continuous fluidized beds

Average gas holdup and gas-to-liquid mass transfer in three-phase fluidized beds with non-Newtonian fluids were studied. The effects of liquid property, gas distributor type and magnetic field intensity on mass transfer coefficient and overall gas holdup were examined. The volumetric gas-to-liquid mass transfer coefficient was determined by fitting the oxygen concentration profile data across the bed to the axial dispersion model. The average gas holdup and mass transfer coefficient were all correlated with operating parameters including gas velocity and effective viscosity.Experimental results showed that a three-fold increase in mass transfer coefficient and a two-fold increase in average gas holdup were observed with properly designed liquid property and gas distributor. A modified process was developed to highly elevate the volumetric gas-to-liquid mass transfer rate. The bubble coalescing property of three-phase fluidized beds with small particles is eliminated, and its application to biotechnology and enzyme-catalyzed processes with high gas-to-liquid mass transfer rate could be achieved.     

气液固三相循环流化床气液传质行为

<正>气液固三相流化床反应器在石油化工、湿法冶金、环境工程和煤的液化等工业领域得到了广泛应用,其基础研究也取得了很大进展.但是,传统三相床主要应用于低液速(U_L<     

高温高压浆态鼓泡床反应器中的气-液传质

The gas-liquid mass transfer of H2 and CO in a high temperature and high-pressure three-phase slurry bubble column reactor is studied. The gas-liquid volumetric mass transfer coefficients kLa are obtained by measuring the dissolution rate of H2 and CO. The influences of the main operation conditions, such as temperature, pressure,superficial gas velocity and solid concentration, are studied systematically. Two empirical correlations are proposed to predict kLa values for H2 and CO in liquid paraffln/solid particles slurry bubble column reactors.