γ-TiAl合金表面Al2O3/Al复合涂层的抗高温熔盐腐蚀性能研究

采用磁控溅射技术于γ-TiAl合金表面制备Al₂O₃/Al复合涂层。在850 °C下、 100 wt.% Na₂SO₄熔盐中观测Al₂O₃/Al复合涂层的高温腐蚀行为。结果表明,Al₂O₃/Al复合涂层具备由Al₂O₃表层、富Al中间层以及互扩散层组成的梯度结构,因而有效地提高了基体γ-TiAl合金的抗高温腐蚀性能。在腐蚀实验后,涂层试样表面相结构为Al₂O₃,TiO₂和TiAl₃。致密的Al₂O₃/Al复合涂层有效地抑制了O_2-,S_-和Na₊对基体γ-TiAl合金的侵蚀。并且,Al₂O₃/Al复合涂层的梯度结构亦使其表现出了优异的抗开裂和抗剥落性能。     

La2O3含量对搅拌摩擦加工制备Ni /Al复合材料组织和性能的影响

采用搅拌摩擦加工方法在Al基体中添加不同La₂O₃含量的混合粉末(Ni+La₂O₃),制备 (Ni+La₂O₃)/Al复合材料。采用SEM、EDS、 EPMA及XRD对复合区微观结构及相组成进行分析,采用室温拉伸试验对 (Ni+La₂O₃)/Al复合材料力学性能进行了测试。结果表明,随着La₂O₃含量的增加,(Ni+La₂O₃)/Al复合材料的组织和性能先变好后变差。当La₂O₃添加量达到5%时,复合材料中Al₃Ni增强颗粒分布均匀、颗粒数量最多,块状的Ni粉团聚减少,其抗拉强度达到最大值215MPa,相比Ni/Al复合材料(抗拉强度176MPa),其抗拉强度提高了22%;当La₂O₃的添加量为7%时,复合材料中Al₃Ni增强颗粒含量减少,块状Ni粉团聚重新出现,抗拉强度下降至201MPa。     

基于磁过滤技术的热障涂层表面Al2O3 覆盖层抗CMAS腐蚀性能

为了提高热障涂层（TBC）的抗沉积物（主要成分为CaO、MgO、Al₂O₃和SiO₂,简称CMAS）腐蚀性能,采用磁过滤阴极真空电弧（FCVA）技术在TBC表面上制备了致密的Al₂O₃覆盖层,比较和分析了Al₂O₃改性TBC和沉积态TBC的润湿行为和抗CMAS腐蚀性能。结果表明：使用FCVA技术制备Al₂O₃覆盖层的过程对7%（质量分数）氧化钇稳定的氧化锆（7YSZ）相的结构无明显影响,且经Al₂O₃改性的TBC综合性能均优于沉积态TBC。在1250 ℃、CMAS腐蚀条件下,Al₂O₃覆盖层有效地限制了熔融CMAS在TBC表面上的扩散行为。同时,Al₂O₃填充了7YSZ柱状晶之间的间隔并且阻碍了熔融CMAS的渗透,证明了FCVA可作为一种制备Al₂O₃涂层的新方法以提高TBC的抗CMAS腐蚀性能,且Al₂O₃涂层及其制备过程对TBC的热震性能均无消极影响。     

ZrB2增韧Al2O3陶瓷制备工艺及其对复相陶瓷力学性能影响

Al₂O₃陶瓷因具有很高的强度和耐蚀性受到广泛关注。但由于相对较差的韧性限制了其广泛应用。Al₂O₃陶瓷增韧的方式很多,本文采用微米ZrB₂来增韧氧化铝陶瓷,探讨复相陶瓷烧结工艺,并研究工艺参数对复相陶瓷力学性能及韧性的影响。结果表明：采用单因素法得到两种陶瓷最佳工艺参数分别是纯α-Al₂O₃陶瓷烧结温度为1500℃,成型压力为450MPa,保温时间为8h,球料比为1/2,保压时间为10min;ZrB₂(wt,20%)+α-Al₂O₃ (wt,80%)复相陶瓷烧结温度为1450℃,成型压力为450MPa,保温时间为8h,球料比为1/2,保压时间为10min。其中成型压力、烧结温度和保温时间对复相陶瓷硬度及致密度影响最大。ZrB₂的加入,在降低陶瓷烧结温度的同时,可以将纯α-Al₂O₃陶瓷的断裂韧性由5.2±0.3MPa.m^_1/2提高到6.7±0.2MPa.m^_1/2。     

Al2O3/Ti2AlN复合材料在900℃,1000℃和1100℃空气中的氧化行为

利用综合热分析仪、背散射扫描电镜(BSE)和能谱分析(EDS)对Al₂O₃/Ti₂AlN复合材料在900 ℃,1 000 ℃和1 100 ℃/20 h空气中连续氧化20h后的氧化增重及氧化层截面进行了研究。结果表明：Al₂O₃/Ti₂AlN复合材料在空气中的氧化行为符合抛物线规律,在900 ℃,1 000 ℃和1 100 ℃/20 h氧化增重分别为2.78×10_-2 kg/m₂、10.4 ×10_-2 kg/m₂、21.9 ×10_-2 kg/m₂,抛物线速率常数相应为1.08×10_-8 kg₂/m₄s、1.44×10_-7 kg₂/m₄s、6.56×10_-7 kg₂/m₄s,氧化激活能为274 kJ/mol。氧化层主要由TiO₂和Al₂O₃组成的,连续的Al₂O₃次外层可以提高其抗氧化性能。氧化层结构的改变是由于氧化温度对Ti₄₊、Al₃₊由基体表面向外扩散和O_2-向内扩散的影响,以及TiO₂和Al₂O₃在不同温度下的形核生长速率导致的。对Al₂O₃/Ti₂AlN而言,控制材料与氧化气氛的界面是提高该材料抗氧化性能的关键。     

W18O49@Cu2O纳微米复合材料的制备及其光催化性能研究

本文首先用热蒸发方法制备得到了W₁₈O₄₉纳微米棒,然后经醋酸铜饱和溶液浸泡后再热处理的办法成功在W₁₈O₄₉纳微米棒表面负载Cu₂O制得得到了W₁₈O₄₉@Cu₂O纳微米复合材料;采用X-射线衍射仪、扫描电子显微镜、X-射线能谱分析及透射电子显微镜对样品进行分析表征;最后选用亚甲基蓝溶液作为目标降解物模拟污水处理测试材料的光催化性能。实验结果表明,W₁₈O₄₉纳微米棒在饱和醋酸铜溶液中浸泡时间越长,所得到的催化剂中Cu₂O的负载量越多,且所制备的W₁₈O₄₉@Cu₂O的纳微米复合材料相对于纯W₁₈O₄₉纳微米棒,其光催化效率得到了显著提高。     

304不锈钢表面Ni-Al2O3复合镀层制备及性能研究

采用复合电沉积法在304奥氏体不锈钢表面制备Ni-Al₂O₃纳米镀层. 研究了Al₂O₃颗粒在复合镀层中的分布情况, 确定了镀液中颗粒的最佳加入量、最佳电流强度和最佳搅拌速度. 用扫描电镜和能谱仪、X射线衍射仪等设备鉴定镀层显微组织与组成. 结果表明, Ni-Al₂O₃纳米复合镀层均匀、致密、晶粒细小; 复合镀层结合强度、耐腐蚀性能优良, 抗高温氧化性能优于纯镍镀层.     

SNDC/La2Mo2O9复合电解质材料的制备及性能表征

本文采用甘氨酸-硝酸盐法(GNP)和溶胶凝胶法分别合成了Sm_0.1Nd_0.1Ce_0.8O_1.9(SNDC) 和La₂Mo₂O₉(LAMOX)粉末,并用常压烧结的方法制备了不同比例的SNDC和LAMOX的复合材料,通过XRD和SEM等手段表征了不同复合比例样品的物相和表面形貌并测试了烧结样品的电导率。结果表明,复合样品的电导率在相变点前后随着复合量增加变化趋势相反,其中LAMOX含量为20mol%的样品在550℃时的电导率能达到0.01S/cm,高于同温度下SNDC电导率。     

三元共晶成分Al2O3/YAG/ZrO2粉体及陶瓷的制备与组织性能研究

本文采用醇水共沉淀法制备了三元共晶成分Al₂O₃/YAG/ZrO₂粉体,在600-1350_oC温度范围煅烧后研究其物相转变过程。经1300_oC煅烧后Al₂O₃/YAG/ZrO₂共晶成分粉体的物相由α-Al₂O₃、c-ZrO₂和YAG构成,且具有α-Al₂O₃相包裹c-ZrO₂相的特殊结构。将煅烧粉体在1550_oC下热压烧结,制备具有内晶型结构的共晶成分Al₂O₃/YAG/ZrO₂复相陶瓷,其致密度、室温抗弯强度、断裂韧性和高温(1000_oC)抗弯强度分别为98.8%、420 MPa、3.69 MPa.m_1/2和464 MPa,并对复相陶瓷组织结构的形成机理进行了探讨。     

Al2O3微粉添加量对镁合金微弧氧化膜特性影响研究

为了研究添加Al₂O₃微粉对AZ31A镁合金微弧氧化膜特性影响,在不同浓度Al₂O₃微粉电解液中对其进行了微弧氧化处理。利用扫描电镜(SEM)观察微弧氧化膜形貌,能谱仪(EDS)分析了膜层表面Ca、Mg、O、Al元素分布,X射线衍射仪(XRD)分析了相组成,测定了膜厚、硬度和氧化液中Al₂O₃表面电荷,讨论了掺杂改性机理。结果表明,加入Al₂O₃微粉后,氧化电压随Al₂O₃添加量增加先增加后降低;氧化膜表面孔洞数量和尺寸减小,膜层表面Ca元素分布逐渐减少,成膜效率降低,膜层致密度和表面疏松层硬度提高,氧化膜主要由MgO和MgO₄等相组成。     

Synthesis and characterization of Al2O3-Ce0.5Zr0.5O2 powders prepared by chemical coprecipitation method

Al₂O₃-Ce_0.5Zr_0.5O₂ catalytic powders were synthesized by the coprecipitation (ACZ-C) and mechanical mixing (ACZ-M) methods, respectively. As-synthesized powders were characterized by XRD, Raman spectroscopy, surface area and thermogravimetric analyses. It was found that the mixing extent of Al³⁺ ions affected the phase development, texture and oxygen storage capacity (OSC) of the Ce_0.5Zr_0.5O₂ powder. Single phase of ACZ-C could be maintained without phase separation and inhibit α-Al₂O₃ formation up to 1200 °C. The specific surface area value of ACZ-C (81.5 m²/g) was larger than that of ACZ-M (62.1 m²/g) and Ce_0.5Zr_0.5O₂ (17.1 m²/g) powders, which were calcined at 1000 °C. In comparison with ACZ-C and Al₂O₃, which were calcined at high temperature (900–1200 °C), it was found that the degradation rate of specific surface area of ACZ-C was lower than that of Al₂O₃. ACZ-C sample showed a higher thermal stability to resist phase separation and crystallite growth, which enhanced the oxygen storage capacity property for Ce_0.5Zr_0.5O₂ powders.     

La2O3含量对Al2O3/Cu基复合材料组织与性能的影响

以La₂O₃粉、Al粉、CuO粉为反应物原料、纯铜为基体,采用原位合成技术和近熔点铸造法制备颗粒增强Cu基复合材料,研究La₂O₃对Al-CuO体系制备的Cu基复合材料组织及性能的影响。结果表明：添加La₂O₃可获得纳米Al₂O₃颗粒,且弥散分布于Cu基体中,制备的材料组织更加细小、均匀,其材料的电导率及摩擦磨损性能明显提高。当添加0.6%wtLa₂O₃,复合材料的电导率达到90.2%IACS,磨损量达到最小,相比未添加La₂O₃,其导电率提高10.1%,磨损量减小36.6%。     

占空比对高频脉冲电沉积( Ni-Co) / 纳米 Al2O3复合镀层的影响

采用高频脉冲电沉积法制备(Ni-Co)/纳米Al2O3复合镀层,研究了占空比对复合镀层沉积速率、成分、形貌及表面显微硬度的影响。结果表明:随着占空比由0.3提高至0.5,复合镀层的沉积速率增加,晶粒尺寸变大,表面变粗糙,并且Co含量降低,Ni含量增加,纳米Al2O3颗粒含量变化不明显,Co含量的降低导致硬度降低。     

Preparation of nanostructured Ni/Al2O3 composite coatings in high magnetic field

Ni/Al₂O₃ composite coatings were prepared by a novel method from a modified Watt's type electrolyte containing nano-Al₂O₃ particles, where a high magnetic field was imposed in the direction parallel to an electrolytic current instead of mechanical agitation. Effects of magnetic field on the content of particles, surface morphology, microhardness and wear resistance of plating layer were investigated. It was found that the high magnetic field played an important role in the formation of composite coatings. The amounts of nano-Al₂O₃ particles in the composite coating increased with increasing of magnetic flux density and reached a maximum value at 8 T, then reduced slightly. The microhardness and wear resistance of the nanocomposite coatings also enhanced with increasing of magnetic flux density as compared to that of pure Ni coating fabricated in the absence of magnetic field. That was because the co-deposited nano-Al₂O₃ particles were uniformly distributed in the Ni matrix and contributed to greatly increase the microhardness and wear resistance of the composite coatings. Moreover, the mechanism of action of high magnetic field was discussed preliminarily.     

Al2O3-nanodiamond composite coatings with high durability and hydrophobicity prepared by aerosol deposition

We attempted the room-temperature fabrication of Al₂O₃-based nanodiamond (ND) composite coating films on glass substrates by an aerosol deposition (AD) process to improve the anti-scratch and anti-smudge properties of the films. Submicron Al₂O₃ powder capable of fabricating transparent hard coating films was used as a base material for the starting powders, and ND treated by 1H,1H,2H,2H-perfluorooctyltriethoxysilane (PFOTES) was added to the Al₂O₃ to increase the hydrophobicity and anti-wear properties. The ND powder treated by PFOTES was mixed with the Al₂O₃ powder by ball milling to ratios of 0.01 wt.%, 0.03 wt.%, and 0.05 wt.% ND. The water contact angle (CA) of the Al₂O₃-ND composite coating films was increased as the ND ratio increased, and the maximum water CA among all the films was 110°. In contrast to the water CA, the Al₂O₃-ND composite coating films showed low transmittance values of below 50% at a wavelength of 550 nm due to the strong agglomeration of ND. To prevent the agglomeration of ND, the starting powders were mixed by attrition milling. As a result, Al₂O₃-ND composite coating films were produced that showed high transmittance values of close to 80%, even though the starting powder included 1.0 wt.% ND. In addition, the Al₂O₃-ND composite coating films had a high water CA of 109° and superior anti-wear properties compared to those of glass substrates.     

Investigation on the corrosion and oxidation resistance of Ni-Al2O3 nano-composite coatings prepared by sediment co-deposition

Ni-Al₂O₃ composite coatings were prepared by using sediment co-deposition (SCD) technique from a Watt's type electrolyte containing nano-Al₂O₃ particles. The corrosion resistance and high temperature oxidation resistance of resulting composite coatings were investigated. It was found that the incorporation of nano-Al₂O₃ particles in Ni matrix refined the Ni crystal and changed the preferential orientation of composite coatings. Meanwhile, the corrosion and oxidation resistance were improved after the incorporation of nano-Al₂O₃ particles into Ni matrix. The nano-Al₂O₃ content in deposits plays an important role for improving the corrosion and oxidation protection. The corrosion and oxidation resistance of Ni-Al₂O₃ nano-composite coatings produced via SCD technique are superior to that of CEP technique. Compared to pure Ni and Ni-Al₂O₃ composite coatings fabricated using CEP technique, the Ni-7.58 wt.% Al₂O₃ composite coating obtained by SCD technique exhibits better corrosion resistance and enhanced high temperature oxidation resistance. Moreover, the mechanism of corrosion and high temperature oxidation resistance of Ni-Al₂O₃ nano-composite coatings are discussed.     

Al_2O_3/MoS_2复合涂层的制备及摩擦磨损性能

以大气等离子喷涂工艺制备的Al_2O_3陶瓷涂层为模板,利用陶瓷涂层中存在的孔隙和微裂纹,采用水热反应在其内部原位合成具有润滑特性的MoS_2,制备出Al_2O_3/MoS_2的复合涂层。结果表明,通过水热反应在陶瓷涂层原有的微观缺陷中成功合成了MoS_2,合成的MoS_2固体粉末呈类球形状,并且这球状的粉末是由纳米片层状的MoS_2搭建组成的。摩擦试验结果表明,与纯Al_2O_3涂层相比,复合涂层中由于MoS_2润滑膜的形成,其摩擦因数和磨损率都显著降低,且载荷越大,复合涂层的摩擦性能越好。     

Microstructure and mechanical properties of Al2O3-Cr2O3 composite coatings produced by atmospheric plasma spraying

Al₂O₃, Al₂O₃-Cr₂O₃ and Cr₂O₃ coatings were deposited by atmospheric plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction. Electron probe microanalyzer was employed to investigate the polished and fractured surface morphologies of the coatings. Mechanical properties including microhardness, fracture toughness and bending strength were evaluated. The results indicate that the addition of Cr₂O₃ is conducive to the stabilization of α-Al₂O₃. Compared with the pure Al₂O₃ and Cr₂O₃ coatings, Al₂O₃-Cr₂O₃ composite coatings show lower porosities and denser structures. Heterogeneous nucleation of α-Al₂O₃ occurs over the isostructural Cr₂O₃ lamellae and partial solid solution of Al₂O₃ and Cr₂O₃ might be occurring as well. Furthermore, grain refining and solid solution strengthening facilitate the mechanical property enhancement of Al₂O₃-Cr₂O₃ composite coatings.     

In-situ TiB2 and Al2O3 formation by DC plasma spraying

In-situ plasma spraying (IPS) is a promising process to fabricate composite coatings with in-situ formed thermodynamically stable phases. In the present study, mechanically alloyed Al-12Si, B₂O₃ and TiO₂ powder was deposited onto an aluminum substrate using atmospheric plasma spraying (APS). It has been observed that, during the coating process, TiB₂ and Al₂O₃ are in-situ formed through the reaction between starting powders and finely dispersed in hypereutectic Al-Si matrix alloy. Also, obtained results demonstrate that in-situ reaction intensity strongly depends on spray conditions.