整体型大孔/介孔PDA/SiO2复合材料固定化漆酶及其在染料降解中的应用

用硬模板法制得具有三维连续贯通孔道结构的整体型大孔/介孔SiO₂，通过多巴胺（DA）在大孔/介孔SiO₂孔道表面的原位氧化聚合，制得聚多巴胺（PDA）功能化修饰的整体型大孔/介孔复合材料（PDA/SiO₂）。应用SEM、BET、FTIR和TG等技术对修饰前后的材料进行表征。以PDA/SiO₂为载体固定诺维信工业级漆酶，系统研究了pH、固定化时间、漆酶初始浓度及温度对漆酶固定化的影响；以偶氮荧光桃红作为模拟污染物，研究了固定化漆酶对染料的催化降解性能。结果显示，在漆酶浓度为80mg/mL、pH为4.0、固定化时间为6h及固定化温度为25℃时，固定化漆酶酶活达到最高（348.9U/g）。在偶氮荧光桃红浓度为10mg/L、pH为7.0、温度为30℃、降解时间为8h时，固定化漆酶对偶氮荧光桃红脱色率 ≥ 99.9%，且固定化漆酶易从反应体系中分离，重复使用性能良好。     

Fischer–Tropsch synthesis over Co–SiO2 catalysts prepared by the sol–gel method

Fischer–Tropsch synthesis was carried out in slurry phase over uniformly dispersed Co–SiO₂ catalysts prepared by the sol–gel method. When 0.01–1 wt.% of noble metals were added to the Co–SiO₂ catalysts, a high and stable catalytic activity was obtained over 60 h of the reaction at 503 K and 1 MPa. The addition of noble metals increased the reducibility of surface Co on the catalysts, without changing the particle size of Co metal significantly. High dispersion of metallic Co species stabilized on SiO₂ was responsible for stable activity. The uniform pore size of the catalysts was enlarged by varying the preparation conditions and by adding organic compounds such as N,N-dimethylformamide and formamide. Increased pore size resulted in decrease in CO conversion and selectivity for CO₂, a byproduct, and an increase in the olefin/paraffin ratio of the products. By modifying the surface of wide pore silica with Co–SiO₂ prepared by the sol–gel method, a bimodal pore structured catalyst was prepared. The bimodal catalyst showed high catalytic performance with reducing the amount of the expensive sol–gel Co–SiO₂.     

ZrO2/SiO2催化剂的制备及其氧化脱硫性能研究

以己内酰胺-八水氧氯化锆低共熔溶剂为添加组分,采用溶胶-凝胶法合成含锆的硅胶,再经过高温煅烧得到n-ZrO₂/SiO₂ （n=2%,4%,6%） 负载型催化剂。并用红外光谱（FT-IR）、X射线衍射（XRD）、扫描电镜（SEM）、N₂吸附-脱附、X射线光电子能谱（XPS）对其进行结构表征,确定ZrO₂成功负载到SiO₂上。以ZrO₂/SiO₂为催化剂和吸附剂,H₂O₂为氧化剂组成催化氧化脱硫体系,并应用于模拟油脱硫。分别考察了氧化锆负载量、反应温度、氧硫比、催化剂加入量及不同类型的硫化物对脱硫效果的影响。实验结果表明,在反应温度为70℃、n（H₂O₂）/n（S）=4（摩尔比）、4%-ZrO₂/SiO₂的加入量为0.2 g的最佳反应条件下,氧化脱硫体系对二苯并噻吩（DBT）、4,6-二甲基二苯并噻吩（4,6-DMDBT）和苯并噻吩（BT）的脱除率分别为98.7%、93%和65.9%。且4%-ZrO₂/SiO₂回收利用5次后,DBT脱除率仍可达到91.8%。     

Zn2+掺加的包覆型Fe2O3/SiO2颜料的制备及其呈色性能

包覆型Fe₂O₃/SiO₂颜料由于包覆完整性并不理想,该颜料高于800 ℃时呈色会产生变黑、变暗的问题。采用溶胶-凝胶法制备包覆型Fe₂O₃/SiO₂颜料,研究催化剂浓度、反应温度、硅/铁质量比等因素对包覆型Fe₂O₃/SiO₂颜料呈色性能的影响。在此基础上,通过掺加Zn²⁺,进行了Zn²⁺掺加的包覆型Fe₂O₃/SiO₂颜料的呈色性能研究。研究表明,当催化剂(氨水)浓度为0.75 mol/L,反应温度为40 ℃,硅/铁质量比m(SiO₂)/m(Fe₂O₃)为0.20,铁/锌摩尔比n(Fe)/n(Zn)为4时,制备得到的Zn²⁺掺加的包覆型Fe₂O₃/SiO₂颜料的呈色耐热性能获得明显提升,样品在850 ℃煅烧后仍然呈现出明亮的红橙色色调。     

超稳Y型分子筛的骨架硅铝比对甘油气相脱水反应的影响

以铵交换和高温水热处理法制备了不同硅铝比的超稳Y型分子筛（USY）,利用X射线衍射、扫描电镜、氮气吸附脱附和吡啶红外等技术对USY进行了表征。以USY为催化剂,考察了USY的骨架硅铝比对气相甘油脱水制丙烯醛的影响。X射线衍射和扫描电镜结果表明,铵交换和高温水热处理只是提高USY的硅铝比,相对结晶度略有降低,而对Y型分子筛的结构和形貌没有影响。氮气吸附-脱附和吡啶红外结果表明,随USY骨架SiO₂/Al₂O₃比提高,总酸量和B酸酸量逐渐降低,L酸酸量有所增多,介孔孔体积和平均孔径有所增大。气相甘油脱水反应结果表明,催化剂织构性质对甘油转化率和丙烯醛选择性的影响大于酸性的影响,因而SiO₂/Al₂O₃比为29的USY催化剂的反应性能最好,甘油转化率和丙烯醛收率分别达到了84.5%和51.8%。     

Kinetics and slurry-type reactor modelling during catalytic hydrogenation of o-cresol on Ni/SiO2

The effect of kinetic parameters (reactant concentrations, temperature) was investigated on the initial reaction rate for the catalytic hydrogenation of o-cresol on Ni/SiO₂, carried out in a batch or semi-batch agitated slurry-type reactor.

The data were interpreted by a kinetic model based on the Langmuir-Hinshelwood mechanism with non-dissociative and non-competitive adsorption of o-cresol and hydrogen on different sites, where the limiting step is due to the reaction of adsorbed reactants. The activation energy (E_a = 82 kJ/mol) is in good agreement with previous literature values reported for the catalytic hydrogenation of phenol.

Taking into account thermodynamic (solubilities) and mass transfer kinetics (k_La) data measured in situ, the integral reactor conversion rate of this three-phase catalytic reaction was simulated accurately in the physical regime by taking into account external and internal mass transfer resistances.     

微球形SiO2-Al2O3制备及其流化床蒽醌加氢性能研究

采用喷雾分散-油柱成型制备方法,以硅溶胶为硅源,制备不同含量SiO2掺杂改性的微球形氧化铝载体,研究SiO2含量对氧化铝载体结构及以其为载体的负载型催化剂性能的影响。研究表明,通过掺杂SiO2有效改善了氧化铝微球的热稳定性,且氧化铝载体的孔容、比表面积及酸中心数量均随SiO2含量的增加而增加,孔径随SiO2含量的增加而减小。Pd/SiO2-Al2O3催化剂结构表征及流化床蒽醌加氢性能评价结果表明,掺杂SiO2质量分数6%时,Pd/SiO2-Al2O3催化剂氢化效率大于12.5g·L^-1,选择性大于98.3%。     

Oxidation state of palladium as a factor controlling catalytic activity of Pd/SiO2–Al2O3 in propane combustion

The oxidation state of palladium on SiO₂–Al₂O₃ used for propane combustion was examined by XPS and XRD, and the correlation of the catalytic activity with the oxidation state of palladium was systematically studied. The propane conversion over 5 wt% Pd/SiO₂–Al₂O₃ was measured in the range 1.0≤S≤7.2 (S is defined as [O₂]/5[C₃H₈] based on stoichiometric ratio). The propane conversion strongly depended on the S value and reached the maximum at S=5.5. The oxidation state of palladium also changed with the S value; palladium particles were more oxidized under the reaction mixture of higher S value. On the sample used for the reaction at S=5.5, both of metallic palladium and palladium oxide were found. It is concluded that partially oxidized palladium which has optimum ratio of metallic palladium to palladium oxide shows the highest catalytic activity in propane combustion.     

预成型高岭土干胶转化合成NaY型分子筛

通过干胶转化法制备了整体式NaY分子筛,采用XRD、SEM及XRF分析表征原料及产物,系统考察了合成体系的n（SiO₂）/n（Al₂O₃）、n（Na₂O）/n（SiO₂）、水量、晶化温度和晶化时间对整体式NaY分子筛制备的影响。结果表明,合成体系n（SiO₂）/n（Al₂O₃）=7.5时,骨架硅铝比（二氧化硅与氧化铝物质的量比）最大为6.12;n（Na₂O）/n（SiO₂）逐渐增大,整体式NaY分子筛结晶度逐渐升高,当n（Na₂O）/n（SiO₂）增至0.35时,会导致P型分子筛的生成;晶化温度从90 ℃逐渐增至120 ℃时,整体式NaY分子筛结晶度也随之升高;在110 ℃下晶化20 h,产物的结晶度达到98%并趋于稳定。干胶转化制备整体式NaY分子筛必须有水的参与,n（H₂O）/n（SiO₂）为4.2左右对反应物的成型及整体式NaY分子筛的晶化较为适宜。     

Performance and characterization of Ru/Al2O3 and Ru/SiO2 catalysts modified with Mn for Fischer–Tropsch synthesis

Mn effect and characterization on γ-Al₂O₃-, -Al₂O₃- and SiO₂-supported Ru catalysts were investigated for Fischer–Tropsch synthesis under pressurized conditions. In the slurry phase Fischer–Tropsch reaction, γ-Al₂O₃ catalysts showed higher performance on CO conversion and C₅⁺ selectivity than -Al₂O₃ and SiO₂ catalysts. Moreover, Ru/Mn/γ-Al₂O₃ exhibited high resistance to catalyst deactivation and other catalysts were deactivated during the reaction. From characterization results on XRD, TPR, TEM, XPS and pore distribution, Ru particles were clearly observed over the catalysts, and γ-Al₂O₃ catalysts showed a moderate pore and particle size such as 8 nm, where -Al₂O₃ and SiO₂ showed highly dispersed ruthenium particles. The addition of Mn to γ-Al₂O₃ enhanced the removal of chloride from RuCl₃, which can lead to the formation of metallic Ru with moderate particle size, which would be an active site for Fischer–Tropsch reaction. Concomitantly, manganese chloride is formed. These schemes can be assigned to the stable nature of Ru/Mn/γ-Al₂O₃ catalyst.     

PVDF-PFTS/SiO2膜制备及抗混合污染性能

采用表面接枝技术制备了PVDF-PFTS/SiO₂超疏水复合膜,通过扫描电子显微镜（SEM）和红外光谱（FTIR）分析了膜污染前后的表面结构和组成,考察了直接接触式膜蒸馏（DCMD）装置出水电导率和膜通量的变化,利用XDLVO理论分析了PVDF-PFTS/SiO₂超疏水复合膜的抗混合污染性能和机理。结果表明：在1H, 1H, 2H, 2H-全氟辛基三氯硅烷（PFTS）和SiO₂共同作用下,PVDF-PFTS/SiO₂超疏水复合膜表面形成微纳米复合乳突结构,水接触角（WCA）由99°增至155°。与PVDF基膜相比,PVDF-PFTS/SiO₂超疏水复合膜对混合污染物具有较好的抗污染性能;连续运行10h,膜通量和截留率分别保持在10.06kg/(m²·h)和99.80%。XDLVO理论分析表明,PVDF-PFTS/SiO₂超疏水复合膜表面与污染物之间的作用力由引力转变为斥力是其抗混合污染性能增强的主要原因之一。     

Support effects on structure and activity of molybdenum oxide catalysts for the oxidative dehydrogenation of ethane

The structural and catalytic properties of MoO₃ catalysts supported on ZrO₂, Al₂O₃, TiO₂ and SiO₂ with Mo surface densities, n_s, in the range of 0.5–18.5 Mo/nm² were studied for the oxidative dehydrogenation (ODH) of ethane by in situ Raman spectroscopy and catalytic activity measurements at temperatures of 400–540 °C. The molecular structure of the dispersed surface species evolves from isolated monomolybdates (MoO₄ and MoO₅, depending on the support) at low loadings to associated MoO_x units in polymolybdate chains at high loadings and ultimately to bulk crystalline phases for loadings exceeding the monolayer coverage of the supports used. The nature of the oxide support material and of the Mo–O–support bond has a significant influence on the catalytic behaviour of the molybdena catalysts with monolayer coverage. The dependence of reactivity on the support follows the order ZrO₂ > Al₂O₃ > TiO₂ > SiO₂. The oxygen site involved in the anchoring Mo–O–support is of relevance for the catalytic activity.     

用废弃煤矸石制备高比表面积的SiO2-Al2O3二元复合气凝胶

以兖州煤矸石为原料,经过低温焙烧、酸浸除杂、碱熔活化,采用溶胶-凝胶法和真空干燥法制备完整的块状SiO₂-Al₂O₃二元复合气凝胶。通过X射线衍射、扫描电镜、傅里叶变换红外光谱、氮气吸附等检测手段对原料、SiO₂-Al₂O₃气凝胶及其制备过程中得到的中间产物的物理、化学特性进行表征,研究SiO₂-Al₂O₃凝胶的形成机制。实验结果表明,煤矸石经过酸浸除去了大部分的铁、钾、碱土金属等杂质。在经过碱熔活化后,煤矸石主要组分石英和高岭石均转化为非晶态,反应活性提高。制备得到的SiO₂-Al₂O₃气凝胶是以Si-O-Si、Si-O-Al网络结构为骨架的非晶态纳米颗粒聚集体,其堆积密度0.37 g·cm^-3,比表面积483 m²·g^-1,比孔容1.87 cm³·g^-1,平均孔径10.29 nm,最可几孔径9.32 nm,具有较好的介孔特征。     

无定形MnOx/SiO2催化剂的合成及低温催化氧化甲醛机理

甲醛因其污染范围广、持续时间长、危害性大等特性被视为室内有害物质的头号“杀手”。本文采用自组装法于SiO₂表面原位生长MnO_x（MnO_x/SiO₂催化剂）并用于低温催化氧化甲醛的研究,XRD、SEM-EDS、TEM和BET表征显示,MnO_x以无定形态均匀地分布在SiO₂载体表面,同时考察了MnO_x的负载量以及煅烧温度对甲醛催化活性的影响。实验结果表明,优选的质量分数13% MnO_x/SiO₂无定形催化剂具有较大的比表面积（高达164.85m²/g）和丰富的活性位点（Mn³⁺,75.6%）,而较大的比表面积有利于更多的甲醛分子吸附在催化剂表面并进行活化反应。对甲醛进行连续性动态检测,结果显示催化剂在连续催化6h后仍保持80%以上的去除效率,表明无定形催化剂具有良好的低温催化效果。随着温度的升高,催化甲醛过程中间产物（甲酸根）被进一步分解,有利于催化剂的再生使用,当温度达到90℃时,甲醛的去除效果可达90%。     

疏水纤维素/SiO2复合气凝胶的制备和表征

以微晶纤维素和正硅酸乙酯(TEOS)为原料,通过溶胶-凝胶法制备了4种再生纤维素/SiO₂复合气凝胶,并利用十八烷基三氯硅烷(OTS)对复合气凝胶进行疏水改性,利用X射线衍射(XRD)、能谱仪(EDS)、傅里叶变换红外光谱(FT-IR)、扫描电子显微镜(SEM)等对4种再生纤维素/SiO₂复合气凝胶及其疏水改性产物进行表征分析。结果表明:4种再生纤维素/SiO₂复合气凝胶均为白色固体,密度范围43.6~50.7 mg/cm³;XRD、EDS和FT-IR分析表明4种再生纤维素/SiO₂复合气凝胶中均含有硅元素,疏水纤维素/SiO₂复合气凝胶中均含有硅、氯元素;SEM分析表明4种再生纤维素/SiO₂复合气凝胶及其改性产物均呈现三维网状结构,改性产物的三维网状结构的孔隙变小。疏水纤维素/SiO₂复合气凝胶的接触角测试结果表明,4种样品接触角均大于90°,达到疏水状态,且随着TEOS用量的增加,接触角逐渐增大(最大接触角144.5°),疏水性能提高。     

A high propylene productivity over B2O3/SiO2@honeycomb cordierite catalyst for oxidative dehydrogenation of propane

Boron-based metal-free catalysts for oxidative dehydrogenation of propane (ODHP) have drawn great attention in both academia and industry due to their impressive activity and olefin selectivity. Herein, the SiO₂ and B₂O₃ sequentially coated honeycomb cordierite catalyst is designed by a two-step wash-coat method with different B₂O₃ loadings (0.1%-10%) and calcination temperatures (600, 700, 800 ℃). SiO₂ obtained by TEOS hydrolysis acts as a media layer to bridge the cordierite substrate and boron oxide via abundant Si-OH groups. The welldeveloped straight channels of honeycomb cordierite make it possible to carry out the reactor under high gas hourly space velocity (GHSV) and the thin wash-coated B₂O₃ layer can effectively facilitate the pore diffusion on the catalyst. The prepared B₂O₃/SiO₂@HC monolithic catalyst exhibits good catalytic performance at low boron oxide loading and achieves excellent propylene selectivity (86.0%), olefin selectivity (97.6%, propylene and ethylene) and negligible CO₂ (0.1%) at 16.9% propane conversion under high GHSV of 345,600 ml·(g B₂O₃)^-1·h^-1, leading to a high propylene space time yield of 15.7 g C₃H₆·(g B₂O₃)^-1·h^-1 by suppressing the overoxidation. The obtained results strongly indicate that the boron-based monolithic catalyst can be properly fabricated to warrant the high activity and high throughput with its high gas/surface ratio and straight channels.     

Synthesis and crystal structure of carbonate cancrinite Na8[AlSiO4]6CO3(H2O)3.4, grown under low-temperature hydrothermal conditions

The synthesis of cancrinite in the system Na₂O–SiO₂–Al₂O₃–Na₂CO₃–H₂O was studied under low-temperature hydrothermal conditions in the 353 K<T<473 K interval. The aim was to reveal the suitable range for the crystallization of pure-phase carbonate cancrinite with the ideal composition Na₈[AlSiO₄]₆CO₃(H₂O)₂ without cocrystallization of sodalite or intermediate disordered phases between cancrinite and sodalite. It was found that cancrinite formation reacts very sensitive on the temperature within the autoclaves whereas the concentration of reactants and the alkalinity of the hydrothermal solution have a much lower influence on the phase formation. Thus the temperature of crystallization of carbonate cancrinite without any by-products should not remain below 473 K. At the lower reaction temperature of 353 K the formation of a disordered intermediate phase between the cancrinite and the sodalite structure has been obtained in every case, independent of the template concentrations and the base. Some problems to detect this in a typical powder product mixture are discussed. Besides the ²⁹Si and ²⁷Al MAS NMR characterization of the products, the crystal structure refinement of pure carbonate cancrinite of ideal composition Na₈[AlSiO₄]₆CO₃(H₂O)_3.4, has been carried out from X-ray powder data using the Rietveld method: P6₃, a=1271.3(1) pm, c=518.6(1) pm, R_WP=0.073, R_F=0.016 for 347 structure factors and 45 variable positional parameters.     

Synthesis, characterization and evaluation of NiMo/SiO2–Al2O3 catalysts prepared by the pH-swing method

NiMo/(X)SiO₂–Al₂O₃ catalysts were synthesized with various SiO₂ contents (X = 0, 10, 25 and 50 wt%) using the pH-swing method. In order to find the optimum SiO₂ content, the catalysts were evaluated in the hydrodesulfurization of 4,6-DMDBT, hydrogenation of naphthalene and hydrodenitrogenation of carbazole. Kinetic parameters of Langmuir–Hinshelwood type equations for all the reaction systems were estimated. FTIR analysis of CO adsorption for the sulfided catalysts shows that the amount of coordinatively unsaturated Mo sites promoted by nickel (CUS-NiMoS) follows the order NiMo/10ASA > NiMo/25ASA > NiMo/0ASA. This tendency agrees with the results obtained in catalytic activity.     

Synthesis of high surface area supported Pt/SiO2 catalysts from H2PtCl6·6H2O by the sol-gel method

A new method has been used to prepare highly dispersed Pt/SiO₂ catalysts. The method is based on the use of metal alcoxides together with the appropriate metal precursor. In particular, H₂PtCl₆·6H₂O and tetraethoxysilane were used to prepare supported Pt/SiO₂ catalysts with a BET surface area in excess of 1000 m²/g. Catalysts prepared by this method were observed to resist deactivation by sintering and coke formation and were observed to have a high selectivity in the hydrogenation of phenylacetylene to styrene.     

Selective oxidation of propylene to acrolein over supported V2O5/Nb2O5 catalysts: An in situ Raman, IR, TPSR and kinetic study

The vapor-phase selective oxidation of propylene (H₂CCHCH₃) to acrolein (H₂CCHCHO) was investigated over supported V₂O₅/Nb₂O₅ catalysts. The catalysts were synthesized by incipient wetness impregnation of V-isopropoxide/isopropanol solutions and calcination at 450 °C. The catalytic active vanadia component was shown by in situ Raman spectroscopy to be 100% dispersed as surface VO_x species on the Nb₂O₅ support in the sub-monolayer region (<8.4 V/nm²). Surface allyl species (H₂CCHCH_2*) were observed with in situ FT-IR to be the most abundant reaction intermediates. The acrolein formation kinetics and selectivity were strongly dependent on the surface VO_x coverage. Two surface VO_x sites were found to participate in the selective oxidation of propylene to acrolein. The reaction kinetics followed a Langmuir–Hinshelwood mechanism with first-order in propylene and half-order in O₂ partial pressures. C₃H₆-TPSR spectroscopy studies also revealed that the lattice oxygen from the catalyst was not capable of selectively oxidizing propylene to acrolein and that the presence of gas phase molecular O₂ was critical for maintaining the surface VO_x species in the fully oxidized state. The catalytic active site for this selective oxidation reaction involves the bridging VONb support bond.