On design of a novel class of selective CIC FIR filter functions with improved response

The Cascaded-Integrator-Comb (CIC) filter is a non-recursive (FIR) filter which is multiplier free, consisting only of two building blocks (simple integrator stage and simple comb filter stage) and has a linear phase. This paper summarizes some key points of classical CIC filters and proposes a novel class of CIC FIR filter functions. A novel class of CIC filter functions maintains simplicity of FIR filters by avoiding the multipliers, but shows excellent performances in term of insertion loss in stopband and selectivity with respect to conventional CIC filters. A set of simulations along with illustrative examples is conducted in order to compare the attenuation characteristics of the classical CIC filter functions and the proposed novel class of selective CIC FIR filter functions. For the same level of a constant group delay τ = 45.5 s, a classical CIC filter function has insertion loss of 166.3 dB, and designed novel filter function has a higher level of insertion loss 206.55 dB.     

Improved performance step impedance lowpass filter

Performances of the conventional Butterworth step impedance lowpass filters (LPF) are significantly improved by placing transmission zero either closer to the cut-off frequency (f_c) or away from it. It is achieved by using transverse resonance width of the capacitive line sections. We report method of designing transverse resonance type LPF (TR-LPF) for 5 to 11-pole filters. At f_c = 2.5 GHz, we obtained selectivity in the range 113.3–56.66 dB/GHz and 20–60 dB rejection BW in the range 9.61–7.29 GHz. The TR-LPF can suppress the stopband signal by 60 dB up to 5f_c. Insertion loss in passband is within 0.72 dB. Improved performance of TR-LPF can be designed for f_c up to 7.5 GHz.     

Compact circular-patch-based bandpass filter for ultra-wideband wireless communication systems

Ultra-wideband (UWB) is a radio technology that enables low-power-level, short-range, and wide-bandwidth communication, and it has been widely applied in personal area networks, precision geolocation, medical, surveillance, and vehicular radar systems. Since Federal Communications Commission released the unlicensed use of the UWB range (3.1–10.6 GHz), a significant attention has been paid to the development of UWB devices, particularly UWB bandpass filters. In this paper, we propose a novel UWB bandpass filter based on circular patch resonator that is grounded by via and perturbed by slits and defected ground structures. The resonator’s behaviour is analysed in detail and it is shown that its specific configuration allows a flexible control of the three lowest resonant modes, which are used to form UWB passband. To demonstrate the potential of the resonator, a UWB filter has been designed, fabricated, and measured. The filter is characterized by the insertion loss lower than 1 dB and return loss higher than 17 dB within the passband, as well as by very small group delay variation of only 0.07 ns. Also, the filter exhibits suppression higher than 19 dB up to 30 GHz, and very small overall dimensions of only 0.31λ_g × 0.31λ_g, and thus it outperforms other published UWB filters.     

Broadband bandpass filters using slotted resonators fed by interdigital coupled lines for improved upper stopband performances

This paper proposes new broadband microstrip bandpass filters based on slotted linear tapered-line resonator (SLTR) and slotted step impedance resonator (SSIR) structures for size reduction and improved stopband performances. A comprehensive treatment of slotted resonators and both ends of the resonator with interdigital coupled lines is described. The design concept is demonstrated by two filter examples including one with an SLTR and another one with an SSIR. These filters have not only compact size but also a wider upper stopband resulting from resonator bandstop characteristics. The simulated and experimental results of stopband performances are better than 15 dB for a frequency range up to 25 GHz.     

Microstrip dual-band bandpass filter with independently tunable passbands using varactor-tuned stub loaded resonators

In this paper, a dualband bandpass filter with independently tunable passband is proposed. Two half-wavelength resonators with shunt stub have been placed side by side, fed with a common input-output microstrip line to achieve the individual tunability without affecting other passband. For tuning resonance frequency, varactor diodes are used at the ends of the half wavelength resonators and also at the end of the shunt stubs. Proper shunt stub length and width are derived numerically in such a way that only one control voltage is required in each passband. Measured results show that lower passband can be tuned in a frequency range from 1.78 to 1.96 GHz, whereas the upper passband varies from 2.27 to 2.39 GHz individually. H shaped DGS is integrated below the input-output feed lines to suppress higher order harmonics up to 21 GHz with more than 19 dB attenuation.     

Design of microstrip wide stopband quad-band bandpass filters for multi-service communication systems

This paper presents two planar high performance quad-channel bandpass filters, which are designed based on a novel circular multi-mode resonator. In this paper and for the first time, the proposed resonator is utilized to achieve quad passbands. It consists of diverged feeding lines that are coupled to etched circular cells. The first filter has quite close channels at 2.62, 2.88, 4.34 and 4.67 GHz, which make it appropriate for frequency division duplex (FDD) scheme. Meanwhile, the second filter is designed for WCDMA and WiMAX applications. Both filters are able to attenuate the harmonics up to 19 GHz with a maximum harmonic level of −20 dB. The insertion losses and return losses of both filters at all channels are better than 1.2 dB and 17.5 dB, respectively. The harmonic attenuation method is presented employing a LC equivalent circuit of the proposed resonator. In order to verify the designing methodology, the proposed filters are fabricated and measured where there are good agreements between the simulation and measurement results.     

Log-domain high-order low-pass and band-pass filters

Continuous time current-mode high-order low-pass and band-pass filters based on the log-domain concept are presented in this paper. The passive RLC ladder networks are used as the prototype to achieve the proposed filter by simulating the RLC network synthesis method. The achieved filters have inherited the good sensitivity performance from the RLC passive prototype. Fifth-order RLC ladder low-pass filter and sixth-order RLC ladder band-pass filter are used as prototypes and the signal flow graph (SFG) technique is used for the synthesis. The SFG can identify group of integrators and several signal paths. Log-domain lossy and lossless integrators based on BJT technology are deployed to achieve the integrators for realization of proposed filters. The simulations were carried out and the results exhibited several features which are in agreement with the RLC prototype. The frequency response of filters along 100 kHz to 10 MHz can be electronically tuned through 5–500 µA of bias currents. The THD lower than 1% of LP and BP filters were measured at 10 MHz input. The multi-tone tested was included in the paper for verifying the performance of proposed LP and BP filters. The intermodulation distortions around −50 dB and −60 dB were also investigated for the proposed LP and BP filters.     

Compact differential bandpass filter with a narrow notched band using APCL structure suitable for UWB application

A compact differential band pass filter with asymmetric parallel-coupled lines (APCL) and center frequency of 5.6 GHz is proposed in this paper. The APCL suppresses unwanted RFID signals by introducing a fully tunable notched band at 6.8 GHz. By combining the concept of transmission matrix with modal analysis and extracting a novel model for symmetric three parallel coupled lines (SPCL), role of each resonant frequency is clearly explained. Measurement results in the differential mode show a pass band from 3.1 to 8.1 GHz and a wide stop band from 9.1 to 16 GHz with attenuation of more than 20 dB. In addition, S₂₁ in common mode is lower than −10.5 dB over the pass band.     

Compact triple-passband bandpass filter based on new modified stepped impedance resonators

This study proposed a triple-passband bandpass filter with compact size, low loss and high passband selectivity. The filter includes two coupled stepped impedance resonators (SIRs) and two embedded stub-loaded stepped impedance resonators (SL-SIRs), connected with coupling scheme at the symmetric plane of the filter. The filter is designed to have triple-passband at 2.4, 3.5 and 5.2 GHz for worldwide interoperability for microwave access (WiMAX) applications. By properly tuning the impedance ratio and physical length ratio of the SL-SIRs, the three passbands can be easily determined, at the same time, achieving the high passband selectivity and wide stopband. Besides, the transmission zeros near passband edges of each passband are generated by the proposed filter with cross-coupling structure. The measured results are in good agreement with the full-wave electromagnetic (EM) simulation results.     

A low-transconductance OTA with improved linearity suitable for low-frequency Gm-C filters

A fully differential operational transconductance amplifier is presented in this paper with enhanced linearity and low transconductance, suitable for low-frequency Gm-C filters. This paper also proposes a new common-mode feedback scheme that presents low sensitivity to large differential voltage swings at the OTA outputs. The proposed OTA was employed in the design of a fully-integrated Gm-C low-pass filter with a cutoff frequency of 30 kHz. The Gm-C filter was fabricated in a 0.35 μm CMOS technology and presented a THD at the output less than 1% for input signals with differential amplitudes up to 3.2 V.     

E-Plane Integrated Circuit Filters with Improved Stopband Attenuation (Short Papers)

Improved stopband attenuation is achieved by thick strips, by reduced waveguide sidewall dimensions, and by double planar integrated circuits. In contrast to thick strips which may cause high passband insertion losses and filters with reduced waveguide dimensions which require additional tapers, double planar E-plane integrated circuit filters combine the advantages of low costs, high stopband, and low passband insertion losses. Computer-aided design of a four-resonator Ka -band double metal insert filter achieves a calculated stopband attenuation between 40 and 60 GHz of more than 50 dB, the calculated minimum passband insertion loss is 0.43 dB (measured 1.8 dB). Higher order mode excitation and finite thicknesses of the inserts are included in the calculations.     

Stable and widely tunable wavelength-spacing single longitudinal mode dual-wavelength erbium-doped fiber laser

In this paper, a novel and simple widely tunable wavelength-spacing single longitudinal mode (SLM) dual-wavelength erbium-doped fiber laser (EDFL) based on the tunable filter group, a passive feedback fiber ring (FFR) and saturable absorber (SA), is proposed and demonstrated experimentally. Experiment results show that the wavelength spacing can tune from 0.8 nm up to 17 nm, which has potential to generate terahertz (THz) waves by photo-mixing the lasing wavelengths in a high-speed photo-detector, and the maximum fluctuation of peak power of EDFL is less than 0.37 dB within 75 min and the optical signal-to-noise ratio is more than 30 dB at room temperature. In the absence of high-speed photo-detector, THz beat-note is also successively observed with the help of an autocorrelator. Moreover, dual-wavelength fiber laser can selectively realize one wavelength lasing by simply tuning filters.     

基于SIW技术的毫米波滤波器研究与设计

基于基片集成波导（substrate integrated waveguide,SIW）结构设计了两款四阶的耦合带通滤波器,使用三维全波电磁场仿真软件HFSS对设计的两款滤波器进行了仿真设计和优化.由仿真结果分析得出,两款滤波器的工作频率均位于毫米波频段.第一款SIW滤波器实现了切比雪夫型响应,中心频率为20 GHz,带宽为2 GHz,通带内的插入损耗低于1.5 dB,回波损耗低于-20 dB,在阻带中对信号的衰减程度可以达到50 dB.第二款SIW滤波器实现了准椭圆函数型的响应,中心频率为29.1 GHz,带宽为300 MHz,通带内的插入损耗低于1 dB,回波损耗低于-20 dB,在通带到阻带的过渡中实现了两个陷波点.仿真结果表明,在毫米波滤波器设计中引入SIW结构,有利于优化滤波器尺寸,得到较好的滤波器性能指标,是毫米波滤波器发展的一个重要方向.     

以ⅡR滤波器作补偿的CIC滤波器设计

为解决积分梳状(CIC)滤波器通带失真大和阻带衰减小对其应用的限制,在分析传统CIC滤波器幅频特性的基础上,给出一种用二阶ⅡR滤波器作为补偿滤波器级联CIC滤波器的改进方法。仿真结果表明,它与同级数规模的内插二阶多项式CIC滤波器、锐化CIC滤波器(SCIC)相比,通带和阻带的性能得到较大改善,实现复杂度较低。因此,它适用于对通带、阻带性能和实现复杂度要求较高的多采样率转换系统。     

Automatic generation of CMOS continuous-time elliptic filters

A procedure for the generation of CMOS, continuous-time, high-frequency g/sub m/-C filters with finite transmission zeros is presented. A third-order elliptic filter with 0.5 dB equiripple passband, 15 MHz cutoff frequency and -23 dB attenuation in the stopband is given as an example. The automatic generation method can be generalised to arbitrary high-order prototypes and higher-frequency filters derived from LC ladders.<>     

A compact planar ultra-wideband bandpass filter with multiple resonant and defected ground structure

A compact bandpass filter with dumbbell shape Defected Ground Structure (DGS) operating on ultra wide pass band (UWB – 3.1 to 10.6 GHz) is proposed. It is based on hybrid microstrip coplanar waveguide (dual sided metal) structure. A Multiple Resonant Structure (MRS) is constructed using coplanar waveguide (CPW) planar transmission line. The MRS makes the resonance using quarter wavelength and half wavelength open-ended CPW. The equispaced three resonances at lower (3.1 GHz), center (6.85 GHz) and higher edge (10.6 GHz) of the whole Ultra Wide Band is achieved using CPW MRS. To make the band as flat as possible, two more resonances are introduced using quarter wavelength microstrip patches on top of the commonly shared substrate, so the proposed filter becomes a five pole bandpass filter. A dumbbell shaped defected ground structure on either side of CPW MRS improves the return loss almost less than 20 dB over the whole UWB passband. The simulated results of proposed filter show good transmission response within passband and good rejection in out of the band. The simulated and measured results are very close to each other which proves the efficacy of proposed design.     

A low-voltage low-power CMOS fully differential linear transconductor with mobility reduction compensation

A highly linear fully differential CMOS transconductor architecture based on flipped voltage follower (FVF) is proposed. The linearity of the proposed architecture is improved by mobility reduction compensation technique. The simulated total harmonic distortion (THD) of the proposed transconductor with 0.4V_pp differential input is improved from ?42 dB to ?55 dB while operating from 1.0 V supply. As an example of the applications of the proposed transconductor, a 4th-order 5 MHz Butterworth Gm-C filter is presented. The filter has been designed and simulated in UMC 130 nm CMOS process. It achieves THD of ?53 dB for 0.4V_pp differential input. It consumes 345 μw from 1.0 V single supply. Theoretical and simulated results are in good agreement.     

新型微波有源滤波器综合方法

本文给出了一种新颖的微波有源滤波器的拓扑结构及综合方法，并对有源滤波电路进行了计算机模拟，结果表明本文给出的微波有源滤波器电路具有优良的的窄带滤波特性，通带内正向增益大于１０ｄＢ，带外抑制大于３０ｄＢ。     

Designing IIR filters with a given 3-dB point

Often in infinite impulse response (IIR) filter design, our critical design parameter is the cutoff frequency at which the filter's power decays to half (-3 dB) the nominal passband value. This article presents techniques that aid in the design of discrete-time Chebyshev and elliptic filters given a 3-dB attenuation frequency point. These techniques place Chebyshev and elliptic filters on the same footing as Butterworth filters, which traditionally have been designed for a given 3-dB point. The result is that it is easy to replace a Butterworth design with either a Chebyshev or an elliptic filter of the same order and obtain a steeper rolloff at the expense of some ripple in the passband and/or stopband of the filter.     

Miniaturized microstrip bandpass filter designed using rectangular dual spiral resonator

A miniaturized microstrip bandpass filter based on a rectangular dual spiral resonator (DSR) is proposed in this paper. The rectangular DSR bandpass filter is centered at 3.65 GHz to suit for Wireless LAN (IEEE802.11y) application. The proposed filter offers transmission zero at the high side of out-of-band response. Across the bandwidth, the measured minimum insertion loss is about 1.7 dB, while the measured return loss is better than 19 dB. Measurement results are good agreement and closed to the simulated ones. The total circuit size of the miniaturized bandpass filter is about 0.145λ_g by 0.135λ_g, where λ_g is the guided wavelength at 3.65 GHz.