R22替代工质蒸发器的性能研究

基于湿球温度效率法,建立了蒸发器的稳态分布参数模型。分别以R22及其3种替代产品(R407C,R410A,R134A)为工质,运用该模型详细比较了在流量变化及风量变化两种情况下2排管蒸发器的换热和流动特性。结果表明：当迎风面风速不变时,随着管内冷媒流量的增大,各种工质蒸发器总换热量、显热换热量、潜热换热量均增大,但潜热换热量增大得更快。压降亦随着管内流量的增大而增大。当管内冷媒流量不变时,随着蒸发器迎风面风速的增大,各种工质蒸发器总换热量、显热换热量均增加,潜热换热量下降,同时压降亦下降,但下降的趋势随着风速的增大而最终趋于平缓。四种工质中,R134A性能较好,但其压降也最大,R410其次,压降最小,但其蒸发压力比R22高出60％左右。R407C与R22在换热量及压降方面最为接近,是其理想的替代产品。     

流程布置对R407C冷凝器性能的影响

本文基于传热单元法，建立了冷凝器的分布参数模型。以R407C为工质，运用该模型详细分析了四种不同流程布置两排管冷凝器的换热和流动特性，并与以R22为工质的冷凝器进行了性能比较。结果表明：采用R407C为工质时，四种流程布置中，无论是随着管内冷媒流量的变化，还是随着冷凝器迎风面风速的变化，逆流布置换热效果都是最好，换热量比顺流高约5％-40％，压降比顺流高约3％-10％，其次是错流布置，顺流布置最差。在与以R22为工质的冷凝器性能比较中，无论是随着管内冷媒流量的变化，还是随着迎风面风速的变化，R407C冷凝器换热量都比R22冷凝器高约3％-5％，压降低约5％-10％，是其理想的替代产品。     

风速对不同流程数CO2蒸发器性能的影响

为研究迎面风速对不同流路数CO₂翅片管蒸发器性能的影响,本文建立分布参数模型对蒸发温度为-25℃,风速为0.5～4 m/s条件下5种流路数CO₂翅片管蒸发器的制冷剂压降、换热量、温度分布及传热系数的变化进行分析,并通过实验验证了蒸发器模型的可靠性。蒸发器模型的换热量、制冷剂压降和风侧压降等参数模拟值与相同工况下实验值的误差均在±4%以内。结果表明:同一流路数蒸发器的换热量、制冷剂压降及传热系数均随风速的增大而增大,而其涨幅随风速增大而减小,综合考虑换热效果和能耗可得最佳风速范围为2.5～3.5 m/s;在一定风速条件下,蒸发器设计时在合理范围内选择较多流路数可有效提升蒸发器换热性能并增强换热均匀性,本次实验中24流路蒸发器为最佳设计方案。     

二氧化碳翅片管式蒸发器模拟与分析

运用分布参数法建立采用CO2的翅片管式蒸发器的数学模型，分析制冷剂侧和空气侧温度、压力和换热的变化情况。同时讨论迎面风速和制冷剂质量流量对蒸发器换热和流动性能的影响，结果表明提高迎面风速可以增加换热效果，但增加的趋势趋于平缓。制冷剂侧压降则成近似线性增大；随着管内工质流量的增大，蒸发器总换热量和制冷荆侧压降都成近似线性增大。这些工作有助于进一步了解CO2在翅片管式蒸发器中的换热和流动特性，并为换热器的优化设计和系统的匹配提供理论依据。     

流路布置对R22替代工质冷凝器性能的影响研究

基于相关文献提出的冷凝器分布参数模型,分别以R22的3种替代产品（R407C,R410A,R134A）为工质,分析了4种不同流路布置的2排管冷凝器的换热和流动特性,并与以R22为工质的冷凝器进行了性能比较。结果表明：采用R22的3种替代工质时,冷凝器性能的变化规律基本一样,4种流路布置中,在随着管内冷媒流量的变化和随着冷凝器迎风面风速的变化两种工况下,逆流换热效果最好,其次是错流,顺流最差;在与R22为工质的冷凝器性能比较中,采用3种替代工质的冷凝器换热量及进出口压降的变化趋势基本一样;在3种替代工质中,R410A性能较好,换热量最大、压降最低,但其冷凝压力比R22高出60%左右,R134A压降较大,这两种都不是理想替代物,而R407C与R22在换热量及压降方面最为接近,是其理想的替代工质。     

冷凝器流程布置方案的研究与探讨

基于传热单元法，建立了冷凝器的稳态分布参数模型。经与前人的实验研究结果进行对比，数值模拟结果与实验结果吻合良好。运用该模型详细分析了六种不同流程布置的二排管冷凝器的换热和流动特性。研究结果表明：单回路冷凝器中，逆流布置换热最好，错流其次，顺流最差；对任一流程布置的冷凝器，当风量不变时，必然存在一最佳冷媒流量使冷凝器性能达到最佳；当冷媒流量保持不变时，也相应存在一个最佳风量，使冷凝器性能最佳。冷凝器流路布置中，重力的影响不可忽略。针对单回路冷凝器进出口总压降过大，沿程压降、热阻及换热系数分布不均匀，提出了一些实用性的分流原则，如双“N”流路，相变点分流等并进行了深入细致的讨论。该研究方法为冷凝器流程布置的优化设计提供了理论基础和指导方向。     

不同空气侧风速下微通道蒸发器换热特性实验研究

搭建微通道蒸发器性能实验台,采用控制变量法研究不同空气侧风速下微通道蒸发器表面温度分布、制冷剂进出口压力的变化规律,计算换热量和换热系数,从而分析空气侧风速对微通道蒸发器的流量分配特性和换热效果的影响。结果表明,随着风速增大,微通道蒸发器制冷剂流量分配不均匀性增大,进出口压力波动振幅和周期增加,压降增大,风速2 m/s时微通道蒸发器换热效果最佳。     

流程布置对R410A冷凝器性能的影响研究

本文基于效率-传热单元法,建立了空冷式冷凝器的分布参数模型.以R410A为工质,运用该模型详细分析了四种不同流程布置两排管冷凝器的换热和流动特性,并与以R22为工质的冷凝器进行了性能比较.结果表明采用R410A为工质时,四种流程布置中,无论是随着管内制冷剂流量的变化,还是随着冷凝器迎风面风速的变化,逆流布置换热效果最好,换热量比顺流高约5～15%,压降比顺流高约3～20%,其次是错流布置,顺流布置最差.在与以R22为工质的冷凝器性能比较中,无论是随着管内制冷剂流量的变化,还是随着迎风面风速的变化,R410A冷凝器换热量都比R22高约6～15%,压降低约30～50%.本研究结论为冷凝器流程布置的优化和设计提供了一定的理论基础和指导方向.     

R22替代工质冷凝器的性能研究

本文基于传热单元法,建立了冷凝器的稳态分布参数模型.分别以R22及其3种替代产品(R407C,R410A,R134A)为工质,运用该模型详细比较了在流量变化及风量变化两种情况下2排管冷凝器的换热和流动特性.结果表明:无论是随着管内冷媒流量的变化,还是随着迎风面风速的变化,换热量及进出口压降的变化趋势基本一样.四种工质中,R410A性能较好(换热量最大,压降最低),但其冷凝压力比R22高出60%左右,R134A由于压降较大,两者都不是R22的理想替代物.R407C与R22在换热量及压降方面最为接近,是其理想的替代工质.     

基于NSGA-III算法的小管径翅片管式蒸发器高维多目标优化

以稳态分布参数法和NSGA-III算法为基础，提出一种翅片管式蒸发器结构参数与流路参数混合寻优的方法，并依此展开小管径蒸发器结构和流路参数的影响分析与流路的高维多目标设计优化。建立的小管径翅片管式蒸发器模型与实测数据的误差在4%以内，可以较好地用于小管径翅片管式蒸发器的计算。基于该模型进一步建立以结构参数与流路参数为自变量，换热量、制冷剂侧压降、空气侧压降以及成本为因变量的神经网络模型，并利用NSGA-III算法对模型进行优化求解，得到小管径翅片管式蒸发器在一定的结构参数变化范围内的最优结构参数及最佳流路。研究结果显示：管外径对小管径翅片管式蒸发器的换热量、制冷剂侧压降以及成本的影响程度最大；翅片间距对小管径翅片管式蒸发器的空气侧压降影响程度最大；翅片厚度对换热量、制冷剂侧压降、空气侧压降以及成本的影响程度均最小；流路主要影响蒸发器的换热量及制冷剂侧压降；制冷剂流路为二支路、三支路和四支路时，模型可输出综合性能最优的结构及流路特征。     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Synthesis of Alumina-Zirconia Nanocomposites by Solgel Process

Al₂O₃-ZrO₂ nanocomposites were developed starting with the solgel process. Composite alumina-zirconia nanopowders were synthesized from metallorganic precursors (Aluminium secondary butoxide and zirconium Iso propoxide) using the solgel process. The parameters affecting the synthesis—solvent, concentration of precursor, R/H ratio (i.e., dilution of water in solvent)—were varied as also the temperature and pH. BET and TEM were used to measure nanosize. Diffuse reflectance spectroscopy and also qualitative optical absorption led to identical particle size estimate. The variation of process parameters was used to study the effect and interdependence of process parameters. Artificial Neural Networks was used to rigorously analyze the process. Although this led to confirmation of interdependence of parameters, the presence of a single overwhelming solvent variable was also established. Then the optimal process was used to synthesize more nanopowder. To produce bulk nanocomposite the nanopowders were sintered by varying the temperature and time period. The sintered lithoids were probed with a vickers hardness tester to measure elastic modulus, hardness, and fracture toughness. The results showed high elastic modulus, modest hardness, and very high fracture toughness.     

Friction Stir Processing Strategies for Uniform Distribution of Reinforcement in a Surface Composite

Friction stir processing (FSP) is an important technique for preparing surface composites. Fabricating defect-free surface composites with uniform particle distribution by FSP is a challenging task. In this study, silicon carbide particles reinforced AA5083 alloy surface composites was fabricated using different FSP strategies including variation in process parameters, dual-tool processing and tool offset overlapping. Material flow of the processed material with reinforcement particles demonstrated that the distribution of particles was influenced by the stirring action of the probe as well as the extrusion of the plasticized material due to the movement of the tool. Process parameters, particularly rotational speed, showed a dominant influence on the distribution of silicon carbide particles.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Instructions & Forms for Authors

Journal of Materials Sciences ＆ Technology is a monthly journal for the rapid dissemination of new, impor- rant results in material and related fields. Submission Electronic files of MS Word and PDF are acceptable. Please visit http：//www.jmst.org and submit online.