考虑土-结构动力相互作用的TMD结构减震控制

本文分析了TMD(Tuned mass damper)在刚性地基和柔性地基情况下的减震控制机理,以某6层钢筋混凝土框架结构为研究对象,分别考虑了土-结构动力相互作用对无TMD控制结构的影响,场地条件对TMD减震控制性能的影响和土-结构动力相互作用对TMD减震控制性能的影响。通过分析得出TMD控制系统的减震效果除了与输入地震动特性有关外,还与场地条件、上部结构和基础的动力特性等因素有关。如果土-结构动力相互作用体系的自振周期远离输入地震动的卓越周期,则相互作用体系的地震响应较小。地基土越软,框架建筑结构层间相对位移地震响应也就越小。如果考虑土-结构动力相互作用效应的影响设计TMD调频系统的自振周期,则TMD的控制效果会有一定程度的提高。     

新型伸臂消能体系的抗震性能研究

以天津某实际工程项目为例,对新型伸臂消能结构体系中消能伸臂的数量、位置和黏滞阻尼器参数进行了优化,比较了这一新型消能体系与常规消能减震方案的减震效果.研究表明,相对于常规消能减震方案,新型伸臂消能结构体系可在布置较少数量阻尼器时,仍获得较好的减震效果,其经济性十分明显,可望在实际工程中进一步推广应用.     

近断层脉冲型地震动作用下高层摩擦摆基础隔震结构的减震性能研究

近断层地震动中长周期、短持时和高能量的加速度脉冲将对高层摩擦摆基础隔震结构的减震性能产生不利影响,考虑土-结构相互作用（SSI效应）后的隔震结构将产生动力耦合效应,可能进一步放大隔震结构地震响应。为此,通过一幢框架-核心筒高层摩擦摆基础隔震结构的非线性地震响应分析,考察近断层脉冲型地震动作用下框架-核心筒摩擦摆基础隔震结构的层间位移角、楼层加速度和隔震层变形等响应规律,揭示隔震体系的损伤机理。基于集总参数SR （sway-rocking）模型,分析不同场地类别与不同地震动类型对隔震体系动力响应影响规律。结果表明:高层摩擦摆基础隔震结构在近断层脉冲型地震动作用下的减震效果相比普通地震动减震效果变差,楼层剪力、层间位移角和隔震层变形等超越普通地震动作用下的1.5倍;对于Ⅲ和Ⅳ类场地类别,考虑SSI效应使隔震结构的地震响应进一步放大,弹塑性层间位移角随着土质变软增大尤为明显。     

基于楼层剪力的等效阻尼比计算方法研究

针对现有附加有效阻尼比计算方法存在的问题,本文从能量的角度揭示了阻尼比对结构影响的机理。从结构设计的角度,提出一种在时程分析下基于楼层剪力的消能减震结构等效阻尼比计算方法。对布置黏滞阻尼器和软钢阻尼器的消能减震模型,采用本文提出的等效阻尼比计算方法,建立等效结构进行结构响应对比。结果表明,由该计算方法得到的等效阻尼比能够准确地评估阻尼器在结构中的耗能效果,建立的等效结构能够准确反映消能减震结构实际情况。基于楼层剪力的等效阻尼比计算方法通过等效结构楼层剪力大于或等于消能减震结构楼层剪力判断迭代完成,该方法计算过程不涉及阻尼器参数及结构形式,适用于所有阻尼器类型与结构类型。计算得到的等效结构进行设计能够确保结构设计的安全。     

体育场震后修复再建中混凝土结构消能减震设计研究

以往是用高层建筑防屈曲支撑的混凝土减震加固方法,以加固震后体育场混凝土结构的防屈曲支撑力为重点,存在的问题是未考虑结构不同部位节点的防屈曲消能减震支撑性能,加固效果差,需要深入研究混凝土结构建筑加固措施,提高震后体育场修复质量。研究采用基于性能和需求的消能减震设计方法,合理布置混凝土的消能支撑结构,在混凝土结构中底层节点设置防屈曲消能减震支撑,其他节点设置黏滞阻尼器,获取最佳阻尼器设置方案,提高结构减震加固效果。仿真实验说明,EL-Centro(NS)地震波和Newhall地震波情况下,所研究方法设计的消能减震新结构平均顶点侧移值分别比原结构小62 mm和110 mm;在不同震级的情况下,节点间位移角新结构小于原结构,说明该方法设计的体育场修复中混凝土结构减震稳定性强,是一种有效的减震加固方法。     

SSI效应对粘弹性阻尼结构减震效果的影响分析

本文以一单跨7层框架结构为研究对象,对不同场地和地震波输入条件下的粘弹性阻尼结构进行了二维有限元时程分析,探讨了SSI（土-结构动力相互作用）效应对粘弹性阻尼结构减震效果的影响。分析结果表明：①在硬土和稍硬土地基条件下,SSI效应明显降低了结构的楼层位移峰值,若在抗震设计中对客观存在的SSI效应加以考虑,设置较少数量的阻尼器（与刚性地基假定条件下确定的阻尼器数量相比）就能使结构的实际地震位移反应满足基于刚性地基假定的地震位移控制目标;②粘弹性阻尼结构的减震效果与场地条件、输入地震动特性密切相关;③与刚性地基相比,SSI效应使粘弹性阻尼结构的减震效果明显降低,且地基越软,降低幅度越大。因此,在实际的工程设计中,应当充分考虑SSI效应,对粘弹性阻尼结构的减震控制效果进行合理的评价,并针对不同的场地条件选用合适的阻尼器类型和性能参数,才有可能达到预期的减震控制效果。     

基于土-结构体系对建筑结构响应的减震效果评估

提出一种基于土-结构体系地震记录的土-结构相互作用(SSI)的减震评估方法。该方法采用简化的SSI模型,通过系统辨识确定模型参数。将上部建筑结构地震反应的SSI减震效应分解为惯性相互作用和运动相互作用,同时还提出由惯性相互作用和运动相互作用单独降低结构响应的方法。将2011年东北地震太平洋沿岸期间两栋中层建筑用此方法进行分析,结果表明:当建筑物结构响应进入非弹性范围时,惯性相互作用的减震效果降低。     

土-桩-钢结构-TLD系统振动台模型试验研究

通过系列振动台模型试验,研究土-结构相互作用对结构TLD减震控制影响。文中首先提出试验模型设计中应考虑的几个主要问题及解决方法,然后介绍土-桩基础-钢结构-TLD相互作用体系的试验成果,分析TLD的减震效果,最后与刚性地基上钢结构TLD减震试验结果相比较,揭示土-结构相互作用对TLD减震效率的影响特点。试验结果表明:土-结构相互作用使得TLD减震效率降低,这一削减作用受到输入地震动的频谱特性和强度的影响。因此,对于建在土层场地上的结构进行TLD减震设计时,应充分重视工程场地条件和地震动特性等实际情况。     

长周期地震动作用下RID-巨-子结构消能控制体系减震性能研究

为了验证旋转惯容阻尼器(RID)对巨-子结构体系在长周期地震动作用下的减震效果,基于强震动观测数据比较了近断层速度脉冲型地震动和远场类谐和地震动这两类长周期地震动的特点,通过建立RID-巨-子结构消能控制体系的振动微分方程,对比分析了两类长周期地震动对RID-巨-子结构消能控制体系和巨-子结构抗震体系地震响应的影响差异。结果表明,相对于巨-子结构抗震体系,RID-巨-子结构消能控制体系能有效减小结构体系在长周期地震动作用下的地震响应,减震效果明显。     

基于损伤性能并考虑主余震作用的消能减震结构抗震设计

综合考虑余震影响和结构损伤,提出一种基于损伤性能的消能减震结构抗震设计方法。为满足结构抵抗余震的性能要求,提出结合主余震的损伤性能目标。以Park-Ang双参数损伤模型为基础建立了结构层间损伤计算公式,通过损伤程度评估结构抗震性能,给出消能减震结构基于损伤性能的抗震设计流程。     

Studies on seismic reduction of story‐incresed buildings with friction layer and energy‐dissipated devices

A new type of energy‐dissipated structural system for existing buildings with story‐increased frames is presented and investigated in this paper. In this system the sliding‐friction layer between the lowest increased floor of the outer frame structure and the roof of the original building is applied, and energy‐dissipated dampers are used for the connections between the columns of the outer frame and each floor of the original building. A shaking table test is performed on the model of the system and the simplified structural model of this system is given. The theory of the non‐classical damping approach is introduced to the calculation analyses and compared with test results. The results show that friction and energy‐dissipated devices are very effective in reducing the seismic response and dissipating the input energy of the model structure. Finally, the design scheme and dynamic time‐history analyses of an existing engineering project are investigated to illustrate the application and advantages of the given method. Copyright © 2003 John Wiley & Sons, Ltd.     

钢管混凝土框架-混凝土核心筒减震结构振动台试验研究

某超高层钢管混凝土框架-混凝土核心筒结构因指标超限在设计中采用了耗能减震技术,为了检验该减震结构的抗震性能,制作了1/35的缩尺模型,通过在钢管混凝土框架设置阻尼器或不设置阻尼器,进行模拟地震振动台对比试验,研究了模型结构的动力特性和不同烈度地震作用下的加速度、位移和应变响应。研究结果表明:地震作用下,该钢管混凝土框架-混凝土核心筒减震结构与钢管混凝土框架-混凝土核心筒结构相比,位移、加速度和应变响应均有一定程度的降低;罕遇地震作用下,通过设置耗能减震构件,层间位移角最大值从超过规范要求的1/84减低至满足规范要求的1/130,表明该减震结构具有更优良的抗震性能。     

D型耗能器偏心支撑结构的抗震性能试验研究

偏心支撑结构是一种高烈度地震区高层建筑钢结构合理的抗侧力体系,本文针对目前偏心支撑结构存在的不足,提出一种新型的框架支撑形式——耗能器偏心支撑;并将该单斜杆(D型)耗能器偏心支撑与支撑斜杆上不加设耗能器的D型偏心支撑结构进行了对比试验。验证了该新型框架支撑形式不仅可以减少耗能梁段吸收的地震能量,而且可以减小耗能梁段的破坏程度,从而减少震后修复工作量;它具有很好的变形能力和足够的抗侧移能力。文中同时给出了设计方法,并提出了改进措施。     

An evaluation of force-based design vs. direct displacement-based design of jointed precast post-tensioned wall systems

The unique features of jointed post-tensioned wall systems, which include minimum structural damage and re-centering capability when subjected to earthquake lateral loads, are the result of using unbonded post-tensioning to attach the walls to the foundation, along with employing energy dissipating shear connectors between the walls. Using acceptance criteria defined in terms of inter-story drift, residual drift, and floor acceleration, this study presents a multiplelevel performance-based seismic evaluation of two five-story unbonded post-tensioned jointed precast wall systems. The design and analysis of these two wall systems, established as the direct displacement-based and force-based solutions for a prototype building used in the PREcast Seismic Structural Systems （PRESSS） program, were performed at 60% scale so that the analysis model could be validated using the PRESSS test data. Both buildings satisfied the performance criteria at four levels of earthquake motions although the design base shear of the direct displacement-based jointed wall system was 50% of that demanded by the force-based design method. The study also investigated the feasibility of controlling the maximum transient inter-story drift in a jointed wall system by increasing the number of energy dissipating shear connectors between the walls but without significantly affecting its re-centering capability.     

Some aspects of floor spectra of 1DOF nonlinear primary structures

In this paper the influence of the nonlinear behaviour of the primary structure on floor spectra is investigated by means of simple models. The general trends of floor spectra for different types of nonlinear behaviour of one degree of freedom (1DOF) primary structure are shown and we point out their common futures and their differences. A special attention is given to the cases of elastoplastic and nonlinear elastic behaviours and methods to determine an equivalent linear oscillator are proposed. The properties (frequency and damping) of this equivalent linear oscillator are quite different from the properties of equivalent linear oscillators commonly considered in practice. In particular, in the case of elastoplastic behaviour, there is no frequency shift and damping is smaller than assumed by other methods commonly used. In the case of nonlinear elastic behaviour, the concept of an equivalent frequency which is a random variable is used. Finally, a design floor spectrum of primary structures, exhibiting energy dissipating nonlinear behaviour is proposed. Copyright © 2006 John Wiley & Sons, Ltd.     

Modeling of energy dissipation in structural devices and foundation soil during seismic loading

Though rocking shallow foundations could be designed to possess many desirable characteristics such as energy dissipation, isolation, and self-centering, current seismic design codes often avoid nonlinear behavior of soil and energy dissipation beneath foundations. This paper compares the effectiveness of energy dissipation in foundation soil (during rocking) with the effectiveness of structural energy dissipation devices during seismic loading. Numerical simulations were carried out to systematically study the seismic energy dissipation in structural elements and passive controlled energy dissipation devices inserted into the structure. The numerical model was validated using shaking table experimental results on model frame structures with and without energy dissipation devices. The energy dissipation in the structure, drift ratio, and the force and displacement demands on the structure are compared with energy dissipation characteristics of rocking shallow foundations as observed in centrifuge experiments, where shallow foundations were allowed to rock on dry sandy soil stratum during dynamic loading. For the structures with energy dissipating devices, about 70–90% of the seismic input energy is dissipated by energy dissipating devices, while foundation rocking dissipates about 30–90% of the total seismic input energy in foundation soil (depending on the static factor of safety). Results indicate that, if properly designed (with reliable capacity and tolerable settlements), adverse effects of foundation rocking can be minimized, while taking advantage of the favorable features of foundation rocking and hence they can be used as efficient and economical seismic energy dissipation mechanisms in buildings and bridges.     

内藏X形软钢板铅复合耗能器的试验研究

遵循“综合利用不同耗能原理或机制来设计新型耗能减震器”思想,研制了内藏X形软钢板铅复合耗能器,并对三种不同构造方式的软钢铅复合耗能器以及一种软钢组合耗能器进行了循环加载的对比试验,分析了这四种耗能器的工作性能与耗能性能,揭示了耗能机制。研究结果表明：内藏X形软钢板铅复合耗能器具有初始刚度较大、极限承载力较高、变形能力与耗能性能良好的特点。因为这种耗能器造价低廉、构造简单、安装方便,有一定的应用价值。     

设置斜撑粘弹性阻尼器框架结构空间协同工作分析方法的控制研究

粘弹性阻尼器（ved）是抗震被动控制中一种十分有效的耗能减震装置。本文根据粘弹性阻尼材料的应力－应变关系，推导了粘弹性阻尼器和人字型支撑的组合层间单元刚度矩阵及单元控制力向量；并基于框架结构的空间特性，建立了设置斜撑Ved框架结构在考虑空间协同分析的基础上地震反应时程分析的控制方法；最后，应用本文的方法，对设置Ved斜支撑后钢筋混凝土框架结构进行了结构地震反应时程分析，并根据计算结果对其减震效果进行了分析讨论。     

Hybrid simulation of a partial-strength steel–concrete composite moment-resisting frame endowed with hysteretic replaceable beam splices

This paper deals with the seismic response assessment of a steel–concrete moment-resisting frame (MRF) equipped with special dissipative replaceable components (DRCs): the dissipative replaceable beam splices (DRBeS), which combine large energy dissipation with ease of replacement. The evaluation of the full potential of DRBeS requires a system-level investigation, that is, a six-story MRF, whereby the hysteretic effects of beam splices partial-strength joints are considered on the global response of the structural system. Therefore, an OpenSees finite element (FE) frame model, based on previous experimental campaigns with cyclic displacements on partial-strength joints, and a Matlab model validated on OpenSees, were used for a more complex experimental activity via hybrid simulation (HS). The aim of the simulations was twofold: (i) to increase knowledge of the non-linear behaviour of steel-concrete composite partial-strength MRFs; and (ii) to study the effectiveness of the DRBeS components for increasing the recovery of functionality after a major seismic event. Therefore, to appreciate the performance of the partial-strength MRF at damage limitation (DL), significant damage (SD) and near collapse (NC) within the performance-based earthquake engineering (PBEE) approach, HSs were carried out. In such instances, the ground floor was physically tested at full scale in the laboratory and the remainder of the structure was numerically simulated. Relevant results showed that the DRBeS were capable of dissipating a significant amount of hysteretic energy and of protecting the non-dissipative parts of partial-strength joints and the overall structure with an ease of replacement.     

楼板隔震消能结构体系

提出了一种新型减震结构体系——楼板隔震消能结构体系。该结构体系的特点是:竖向荷载传递途径与传统结构相同,但在楼板与主体结构水平承重构件之间设置高阻尼隔震层,在楼板与主体结构竖向承重构件之间留出空隙,并在其中安装消能阻尼器,使结构在发生水平振动时楼板与主体结构之间能够发生一定的相对运动,产生隔震和消能作用,减小结构的地震反应。本文给出了单层楼板隔震消能结构的运动微分方程,以及基底输入谐和振动时的结构传递函数,并分析了结构参数对传递函数的影响。