增设节点阻尼器的外附钢框架结构抗震性能试验研究

提出一种组合型减震结构,由钢框架、节点阻尼器和原结构连接组成,外附钢框架将节点阻尼器连接在原混凝土框架结构上形成的增设节点阻尼器的外附钢框架结构,节点阻尼器的剪切滞回变形可以减小结构自身需要消耗的能量,从而提高原结构抗震性能。对原混凝土结构和增设节点阻尼器的组合型结构进行了的振动台试验。通过分析结构在不同地震波激励下的加速度和位移响应,得出楼层加速度和层位移的减震效果。研究结果表明:该结构体系在小震作用下通过提高结构刚度来增强其抗震性能;在大震作用下则可借助节点阻尼器的变形耗能来提升结构耗能能力,结构加速度减震系数达到53%,层间位移减震系数高达72%,验证了增设节点阻尼器的外附钢框架结构的减震效果。     

带防屈曲支撑的钢管混凝土框架抗震性能参数分析

设置防屈曲支撑的钢管混凝土框架是一种新型钢管混凝土减震结构。采用有限元软件Opensees对设置防屈曲支撑的单层单跨钢管混凝土减震框架进行数值模拟,研究了框架梁柱线刚度比、防屈曲支撑初始刚度以及钢管混凝土柱轴压比等设计参数对该减震结构抗震性能的影响。研究结果表明：1数值模拟和试验结果吻合较好,验证了有限元模型的正确性;2梁柱线刚度比在0.1~0.3之间变化时,钢管混凝土减震框架的抗震性能较好;3BRB耗能支撑的初始刚度K1在40~80kN/mm变化时,减震框架的耗能减震效应较明显;4在合理的钢管混凝土柱轴压比范围内,当轴压比较大时,在钢管混凝土框架中设置防屈曲支撑能明显地提高结构的耗能能力和改善结构的强度退化现象。     

大跨径钢管混凝土拱桥减震控制装置参数的研究

大跨度桥梁结构的减震控制研究对于桥梁结构的抗震安全具有重要意义。本文以主跨368m的茅草街大桥为研究对象,基于ANSYS建立了该桥的三维有限元模型,并采用子空间迭代法分析了该桥的动力特性。在此基础上进行了大跨度钢管混凝土拱桥的地震响应及减震控制研究,重点进行了弹性连接装置和粘滞阻尼器减震效果的参数敏感性分析,并对比分析了不同位置布设减震装置时的效果。结果表明,纵飘振型对该桥肋纵向相对位移的贡献最大;弹性连接装置和阻尼器均能有效减小地震作用下该桥的肋梁纵向相对位移;综合考虑各关键部位的地震响应时,同时采用两类减震装置并将其分散布置时的减震效果最佳。结论可供大跨度中承式钢管混凝土系杆拱桥的抗震设计参考。     

高层钢框架-混凝土核心筒混合结构振动台试验研究

为了研究高层钢框架-混凝土核心筒混合结构的整体抗震性能,本文设计了一个典型的比例为1/15的20层钢框架-混凝土核心筒混合结构的缩尺模型,在同济大学土木工程防灾国家重点实验室实施了模拟地震振动台试验。本文重点介绍试验中模型结构在各级水准地震作用下的动力特性、加速度和位移反应,描述了模型结构的破坏位置及过程,并根据相似理论得到了原型结构的地震反应。试验研究表明:原型结构基本能够满足我国现行规范"小震不坏、大震不倒"的抗震设防标准;核心筒发挥了主要抗侧力作用;结构在大震作用下有较好的延性;钢框架与核心筒的连接节点在结构设计时应给予重视。     

附加黏弹性阻尼与金属阻尼耗能的自复位墙结构抗震性能对比分析

相对传统结构,自复位墙结构在地震作用下具有更大的变形能力且几乎无残余位移,但其耗能能力较弱,需采用附加阻尼来增加整体耗能.目前,金属阻尼器已广泛用于自复位墙结构,其可显著减小结构大震下的地震响应,但小震下的位移和加速度减震效果不佳.因此,将小变形下即可耗能的黏弹性阻尼器应用于自复位墙结构中.设计一幢10层自复位墙结构,分别采用黏弹性阻尼器和 U 型金属阻尼器作为附加耗能构件,通过弹塑性时程分析对比采用两种耗能机制的结构地震响应.结果表明,黏弹性阻尼器可显著减小自复位墙结构在小震下的位移和加速度响应;U 型金属阻尼器在中震下开始耗能,在大震和巨震下,其减震效果会超越黏弹性阻尼器.因此,为进一步优化自复位墙结构在不同水准地震作用下的抗震性能,建议结合阻尼器的特点进行合理设计.     

基于Pushover方法的柱端铰型受控摇摆钢筋混凝土框架抗震性能分析

柱端铰型受控摇摆钢筋混凝土框架采用整体结构刚度"弱化"的方式来减小结构的地震作用效应,同时通过设置层间阻尼器来控制结构地震位移响应并消耗地震能量。模拟地震振动台试验研究结果表明,在罕遇地震作用下,模型主体结构未见损伤,结构抗震性能优异。首先介绍柱端铰型受控摇摆钢筋混凝土框架结构形式,并进行有限元计算分析,通过与试验结果对比验证数值建模的正确性,其次使用Pushover分析方法对比和评定无控及受控状态下柱端铰型摇摆框架的抗震性能。分析结果表明,通过设置层间耗能阻尼器,受控柱端铰型摇摆框架的位移响应可以得到有效控制,地震加速度和位移响应满足抗震性能指标。     

基于IDA的方钢管混凝土框架-SPSW核心筒结构地震易损性研究

为研究方钢管混凝土框架-钢板剪力墙（SPSW）核心筒结构在不同强度地震下破坏概率,使用拉杆模型作为钢板剪力墙等效模型,与已有试验对比验证各参数有效性。以地震动峰值加速度（PGA）作为地震动强度参数,按照场地条件等要求选择11条地震动记录。以结构最大层间位移角作为损伤指标,对一典型方钢管混凝土框架-钢板剪力墙核心筒结构进行增量动力分析（IDA）,得到IDA曲线簇。基于增量动力分析进行易损性分析,得到易损性曲线,并计算结构的抗倒塌储备系数。结果表明:8度多遇地震作用下,此结构处于正常使用状态。8度设防地震作用下,处于修复后可使用状态。8度罕遇地震作用下,处于生命安全状态。表明该结构具有良好的抗震性能,满足规范中“小震不坏”、“中震可修”和“大震不倒”的抗震设防目标。该结构抗倒塌储备系数大于规范建议值,具有较好的抗倒塌能力。     

带黏滞阻尼器SRC框支剪力墙结构消能减震分析

针对某型钢混凝土框支剪力墙高层建筑结构高宽比过大、竖向刚度不规则等问题,采用耗能减震技术,在转换层与避难层处设置黏滞阻尼器,采用ETABS进行非线性动力时程分析,研究黏滞阻尼器对型钢混凝土框支剪力墙结构的地震和风荷载控制作用,提高型钢混凝土转换构件的抗震性能。研究结果表明,在不同地震动作用下黏滞阻尼器均能有效地降低型钢混凝土框支剪力墙结构的地震响应,结构峰值位移和最大层间位移角的减幅分别介于3%～45%和2%～43%,而黏滞阻尼器耗散总输入能量比例最高达73.65%;在风荷载时程作用下,结构各控制楼层的峰值位移减幅介于1%～11%之间。     

某型钢混凝土框架核心筒消能减震结构的弹塑性分析

某工程位于昆明市,主体结构高153.1m,为型钢混凝土框架-剪力墙核心筒体系。建筑总高度超过了《高层建筑混凝土结构技术规程》中规定的B级高度,为提高结构的抗震性能,该工程采用消能减震技术控制结构的地震反应,对消能减震结构进行了设计,确定了消能器附加给结构的阻尼比值。为给结构设计提供可靠的参考依据,采用PERFORM-3D软件,对设有非线性粘滞阻尼器的该结构进行罕遇地震作用下动力弹塑性时程分析,评估该结构的整体性能及其构件的屈服情况,结果表明该消能减震结构基本能达到预期抗震性能目标。     

耗能—隔震柔性底层钢管混凝土结构的振动台实验和损伤分析

本文通过一座三层的耗能－隔震柔性底层钢管混凝土结构模型和一座三层普通钢筋混凝土结构模型的振动台实验，着重研究了耗能－隔震柔性底层钢管混凝土结构的抗震性能和减震效果，并与普通的钢筋混凝土结构的实验进行了分析比较，研究了两种结构体系在地震作用下的耗能分布和地震累积损伤情况。     

Modeling of energy dissipation in structural devices and foundation soil during seismic loading

Though rocking shallow foundations could be designed to possess many desirable characteristics such as energy dissipation, isolation, and self-centering, current seismic design codes often avoid nonlinear behavior of soil and energy dissipation beneath foundations. This paper compares the effectiveness of energy dissipation in foundation soil (during rocking) with the effectiveness of structural energy dissipation devices during seismic loading. Numerical simulations were carried out to systematically study the seismic energy dissipation in structural elements and passive controlled energy dissipation devices inserted into the structure. The numerical model was validated using shaking table experimental results on model frame structures with and without energy dissipation devices. The energy dissipation in the structure, drift ratio, and the force and displacement demands on the structure are compared with energy dissipation characteristics of rocking shallow foundations as observed in centrifuge experiments, where shallow foundations were allowed to rock on dry sandy soil stratum during dynamic loading. For the structures with energy dissipating devices, about 70–90% of the seismic input energy is dissipated by energy dissipating devices, while foundation rocking dissipates about 30–90% of the total seismic input energy in foundation soil (depending on the static factor of safety). Results indicate that, if properly designed (with reliable capacity and tolerable settlements), adverse effects of foundation rocking can be minimized, while taking advantage of the favorable features of foundation rocking and hence they can be used as efficient and economical seismic energy dissipation mechanisms in buildings and bridges.     

Analytical predictions of the seismic response of friction damped timber shear walls

A new concept for the earthquake resistant design of timber shear wall structures is proposed. By providing friction devices in the corners of the framing system of the shear wall, its earthquake resistance and damage control potential can be enhanced considerably. During severe earthquake excitations, the friction devices slip and a large portion of the seismic energy input is dissipated by friction rather than by inelastic deformation of the sheathing-to-framing connectors. A simple numerical model is developed and results of inelastic time-history dynamic analyses show the superior performance of the friction damped timber shear walls compared to conventional shear wall systems. The proposed friction devices act both as safety valves by limiting the inertia forces transmitted to the structure, and as structural dampers by dissipating a significant portion of the seismic energy input. The devices can be used in any configuration of the framing system to accommodate architectural or construction requirements. The damping system may also be conveniently incorporated in existing timber shear wall buildings to upgrade significantly their earthquake resistance.     

土体结构相互作用对消能减震结构的影响

本文在考虑土体-结构相互作用的基础上,结合实际工程,对地震作用下的消能减震结构体系进行了对比分析。分析表明,考虑土体-结构相互作用,对于消能减震结构体系的动力特性具有明显的影响。详细考察消能框架体系的楼层位移、楼层速度、楼层加速度以及楼层剪力等指标,在考虑土体-结构相互作用后,减震效果均明显变差;而且上述各指标在各楼层之间减震效果的差异也会增大。     

Studies on seismic reduction of story‐incresed buildings with friction layer and energy‐dissipated devices

A new type of energy‐dissipated structural system for existing buildings with story‐increased frames is presented and investigated in this paper. In this system the sliding‐friction layer between the lowest increased floor of the outer frame structure and the roof of the original building is applied, and energy‐dissipated dampers are used for the connections between the columns of the outer frame and each floor of the original building. A shaking table test is performed on the model of the system and the simplified structural model of this system is given. The theory of the non‐classical damping approach is introduced to the calculation analyses and compared with test results. The results show that friction and energy‐dissipated devices are very effective in reducing the seismic response and dissipating the input energy of the model structure. Finally, the design scheme and dynamic time‐history analyses of an existing engineering project are investigated to illustrate the application and advantages of the given method. Copyright © 2003 John Wiley & Sons, Ltd.     

设置局部粘滞消能支撑的框架节点抗震试验研究

提出了具有位移放大效应的局部粘滞消能支撑的构成及工作原理,开展了设置该类支撑的钢筋混凝土梁-柱节点的反复加载试验,初步考察了节点的抗震性能,并通过对比试验与常规钢筋混凝土梁-柱节点进行了比较。研究结果表明,安装该类支撑后节点的耗能能力明显提高,梁端位移幅值较大时提高幅度可达200%以上,大大改善了节点的抗震性能。     

可控消能减震原理及结构分析

本文介绍一种新的减震结构体系及其分析方法。这种结构体系的减震系统由控制装置及耗能装置组成，控制装置根据结构反馈的相关信号，在回头点处启动耗能装置，耗散大量地震能量，属于半主动控制范畴。试验及理论分析表明，这种结构体系的减震效果良好，能够将结构的地震位移反应降低５０％以上。本文介绍了这种结构体系的减震工作原理、数学模型、理论分析方法及算例，并给出了相应的结论。     

Shaking table tests on reinforced concrete frames without and with passive control systems

An extensive experimental program of shaking table tests on reduced‐scale structural models was carried out within the activities of the MANSIDE project, for the development of new seismic isolation and energy dissipation devices based on shape memory alloys (SMAs). The aim of the experimental program was to compare the behaviour of structures endowed with innovative SMA‐based devices to the behaviour of conventional structures and of structures endowed with currently used passive control systems. This paper presents a comprehensive overview of the main results of the shaking table tests carried out on the models with and without special braces. Two different types of energy dissipating and re‐centring braces have been considered to enhance the seismic performances of the tested model. They are based on the hysteretic properties of steel elements and on the superelastic properties of SMAs, respectively. The addition of passive control braces in the reinforced concrete frame resulted in significant benefits on the overall seismic behaviour. The seismic intensity producing structural collapse was considerably raised, interstorey drifts and shear forces in columns were drastically reduced. Copyright © 2005 John Wiley & Sons, Ltd.     

楼板隔震消能结构体系

提出了一种新型减震结构体系——楼板隔震消能结构体系。该结构体系的特点是:竖向荷载传递途径与传统结构相同,但在楼板与主体结构水平承重构件之间设置高阻尼隔震层,在楼板与主体结构竖向承重构件之间留出空隙,并在其中安装消能阻尼器,使结构在发生水平振动时楼板与主体结构之间能够发生一定的相对运动,产生隔震和消能作用,减小结构的地震反应。本文给出了单层楼板隔震消能结构的运动微分方程,以及基底输入谐和振动时的结构传递函数,并分析了结构参数对传递函数的影响。     

An energy-based method for seismic retrofit of existing frames using hysteretic dampers

This paper proposes a method for the seismic retrofitting of existing frames by adding hysteretic energy dissipating devices (EDDs). The procedure is based on the energy balance of the structure, and it is used to determine the lateral strength, the lateral stiffness and the energy dissipation capacity of the EDDs needed in each story to achieve prescribed target performance levels for a given earthquake hazard. The performance levels are governed by the maximum lateral displacement. The earthquake hazard is characterized in terms of input energy and several seismological parameters, and further takes into account the proximity of the earthquake to the source. The proposed method deals with the effect of the EDDs explicitly in terms of hysteretic energy, bypassing equivalent viscous damping approximations, and directly quantifies the cumulative damage induced in the EDDs. The validity of the method is assessed numerically through nonlinear dynamic response analyses with near-fault and far-field ground motions, as well as experimentally through dynamic shaking table tests.     

楼板隔震消能结构的振动台试验研究

用同一个单层钢框架结构模型,分别做成传统结构体系和楼板隔震消能结构体系。模型在每一种结构体系下分别做模拟地震振动台试验,先后在x向按7度小震和大震烈度输入E l Centro波、Taft波和天津波,比较单层钢框架模型在两种结构体系下的地震反应。试验结果表明,采用楼板隔震消能结构体系能够显著减小结构的加速度反应和底部剪力反应。