BN/Al2O3 复合粉末及其聚合物基复合材料的制备与导热性能

采用固-液相共混法制备了多种BN/Al₂O₃复合粉末,通过冻融法和表面修饰法对BN进行了改性处理,改变表面修饰剂类型和摩尔比得到了前驱体和烧结态BN/Al₂O₃复合粉末,并利用机械混合法制备了聚合物基BN/Al₂O₃复合材料,并测试分析了其导热性能。结果表明,经冻融处理的BN分散性和界面相容性明显优于未经冻融处理的BN。多巴胺对BN的改性效果优于聚乙二醇。采用多巴胺作为表面修饰剂且BN与Al(NO₃)₃的摩尔比为1:1时,能够得到纳米Al₂O₃均匀包覆的微米BN粉末,即BN/Al₂O₃微纳复合粉末,其聚合物基复合材料的导热系数可达0.62 W·m^-1·K^-1,是纯聚合物导热系数的3倍,是采用纯微米BN粉末制备的聚合物基复合材料导热系数的1.5倍。在BN表面附着的Al₂O₃可以形成层状热传导通道,能够有效提高聚合物基BN/Al₂O₃复合材料的热导率。     

γ-TiAl合金表面Al2O3/Al复合涂层的抗高温熔盐腐蚀性能研究

采用磁控溅射技术于γ-TiAl合金表面制备Al₂O₃/Al复合涂层。在850 °C下、 100 wt.% Na₂SO₄熔盐中观测Al₂O₃/Al复合涂层的高温腐蚀行为。结果表明,Al₂O₃/Al复合涂层具备由Al₂O₃表层、富Al中间层以及互扩散层组成的梯度结构,因而有效地提高了基体γ-TiAl合金的抗高温腐蚀性能。在腐蚀实验后,涂层试样表面相结构为Al₂O₃,TiO₂和TiAl₃。致密的Al₂O₃/Al复合涂层有效地抑制了O_2-,S_-和Na₊对基体γ-TiAl合金的侵蚀。并且,Al₂O₃/Al复合涂层的梯度结构亦使其表现出了优异的抗开裂和抗剥落性能。     

原子层沉积Al2O3 保护层氢终端金刚石MISFETs的电学特性

研究了Zr-Si-N氢终端金刚石（H-diamond）绝缘栅场效应晶体管（MISFET）在有无Al₂O₃保护层情况下的电学特性。分别采用原子层沉积法（ALD）和射频溅射法（RF）制备了Al₂O₃保护层和Zr-Si-N栅介质层。MISFETs的转移特性曲线表明,其栅阈值电压在有无Al₂O₃保护的情况下从-2.5 V变化到3 V,表明器件从常关型转换为常开型。输出和转移特性曲线揭示了氧化铝的存在保护了氢终端,使其免受磁控溅射过程的损伤。     

基于磁过滤技术的热障涂层表面Al2O3 覆盖层抗CMAS腐蚀性能

为了提高热障涂层（TBC）的抗沉积物（主要成分为CaO、MgO、Al₂O₃和SiO₂,简称CMAS）腐蚀性能,采用磁过滤阴极真空电弧（FCVA）技术在TBC表面上制备了致密的Al₂O₃覆盖层,比较和分析了Al₂O₃改性TBC和沉积态TBC的润湿行为和抗CMAS腐蚀性能。结果表明：使用FCVA技术制备Al₂O₃覆盖层的过程对7%（质量分数）氧化钇稳定的氧化锆（7YSZ）相的结构无明显影响,且经Al₂O₃改性的TBC综合性能均优于沉积态TBC。在1250 ℃、CMAS腐蚀条件下,Al₂O₃覆盖层有效地限制了熔融CMAS在TBC表面上的扩散行为。同时,Al₂O₃填充了7YSZ柱状晶之间的间隔并且阻碍了熔融CMAS的渗透,证明了FCVA可作为一种制备Al₂O₃涂层的新方法以提高TBC的抗CMAS腐蚀性能,且Al₂O₃涂层及其制备过程对TBC的热震性能均无消极影响。     

三元共晶成分Al2O3/YAG/ZrO2粉体及陶瓷的制备与组织性能研究

本文采用醇水共沉淀法制备了三元共晶成分Al₂O₃/YAG/ZrO₂粉体,在600-1350_oC温度范围煅烧后研究其物相转变过程。经1300_oC煅烧后Al₂O₃/YAG/ZrO₂共晶成分粉体的物相由α-Al₂O₃、c-ZrO₂和YAG构成,且具有α-Al₂O₃相包裹c-ZrO₂相的特殊结构。将煅烧粉体在1550_oC下热压烧结,制备具有内晶型结构的共晶成分Al₂O₃/YAG/ZrO₂复相陶瓷,其致密度、室温抗弯强度、断裂韧性和高温(1000_oC)抗弯强度分别为98.8%、420 MPa、3.69 MPa.m_1/2和464 MPa,并对复相陶瓷组织结构的形成机理进行了探讨。     

原位颗粒对近液相线铸造6063铝合金微观组织和耐磨性的影响机理

以CuO-Al作为反应体系,在6063铝合金中原位反应生成Al₂O₃颗粒,采用近液线相铸造的方法制备6063Al-XAl₂O₃(X=0,2,4,6)复合材料。研究原位反应颗粒Al₂O₃与6063铝合金自带的原位结晶颗粒Mg₂Si的形状、尺寸、数量、分布、界面特征等对合金微观组织和耐磨性的影响机理。结果表明,在6063铝合金中原位反应生成尺寸在亚微米级的近球形θ-Al₂O₃颗粒;其(311)晶面与6063铝合金基体(111)晶面成共格界面;6063铝合金中Mg₂Si尺寸大约为100nm,呈条带状,其(02-2)与Al基体(111)晶面属于共格界面。随着Al₂O₃颗粒含量的增加,6063铝基复合材料的晶粒组织形貌由蔷薇状逐渐向等轴晶转变,晶粒尺寸逐渐减小。当Al₂O₃的质量分数为6%时,复合材料组织由等轴晶和细小的柱状晶组成。载荷为50N时,6063铝合金的磨损量为6.72mg,6063-6Al₂O₃复合材料的磨损量为1.63mg,相对于6063铝合金降低75.7%。原位颗粒(Al₂O₃+Mg₂Si)与铝基体都成共格界面,界面之间无污染,界面结合强度高,在磨损过程中,不易从基体中脱落,承当磨损过程中的大部分载荷。原位生成高硬度的Al₂O₃颗粒与原位结晶颗粒Mg₂Si协同作用共同提高复合材料的耐磨性。外加载荷为40N时,随着增强相质量分数的增加,复合材料的磨损机制由粘着磨损转变为磨粒磨损。6063铝合金磨损机制以严重的粘着磨损为主。6063-2Al₂O₃复合材料磨损机制主要以粘着磨损为主,6063-4 Al₂O₃和6063-6Al₂O₃复合材料主要表现为磨粒磨损。     

Al2O3/Ti2AlN复合材料在900℃,1000℃和1100℃空气中的氧化行为

利用综合热分析仪、背散射扫描电镜(BSE)和能谱分析(EDS)对Al₂O₃/Ti₂AlN复合材料在900 ℃,1 000 ℃和1 100 ℃/20 h空气中连续氧化20h后的氧化增重及氧化层截面进行了研究。结果表明：Al₂O₃/Ti₂AlN复合材料在空气中的氧化行为符合抛物线规律,在900 ℃,1 000 ℃和1 100 ℃/20 h氧化增重分别为2.78×10_-2 kg/m₂、10.4 ×10_-2 kg/m₂、21.9 ×10_-2 kg/m₂,抛物线速率常数相应为1.08×10_-8 kg₂/m₄s、1.44×10_-7 kg₂/m₄s、6.56×10_-7 kg₂/m₄s,氧化激活能为274 kJ/mol。氧化层主要由TiO₂和Al₂O₃组成的,连续的Al₂O₃次外层可以提高其抗氧化性能。氧化层结构的改变是由于氧化温度对Ti₄₊、Al₃₊由基体表面向外扩散和O_2-向内扩散的影响,以及TiO₂和Al₂O₃在不同温度下的形核生长速率导致的。对Al₂O₃/Ti₂AlN而言,控制材料与氧化气氛的界面是提高该材料抗氧化性能的关键。     

Al2O3微粉添加量对镁合金微弧氧化膜特性影响研究

为了研究添加Al₂O₃微粉对AZ31A镁合金微弧氧化膜特性影响,在不同浓度Al₂O₃微粉电解液中对其进行了微弧氧化处理。利用扫描电镜(SEM)观察微弧氧化膜形貌,能谱仪(EDS)分析了膜层表面Ca、Mg、O、Al元素分布,X射线衍射仪(XRD)分析了相组成,测定了膜厚、硬度和氧化液中Al₂O₃表面电荷,讨论了掺杂改性机理。结果表明,加入Al₂O₃微粉后,氧化电压随Al₂O₃添加量增加先增加后降低;氧化膜表面孔洞数量和尺寸减小,膜层表面Ca元素分布逐渐减少,成膜效率降低,膜层致密度和表面疏松层硬度提高,氧化膜主要由MgO和MgO₄等相组成。     

Al0.7Sb2Te3三元靶材的结构性能表征

以原子比Al:Sb:Te=0.7:2:3的混和粉为原料,采用真空合成法与烧结-热等静压制备Al_0.7Sb₂Te₃三元靶材,通过XRD、FESEM、EDS、XPS等手段表征其性能,且重点采用XPS研究Al在Al_0.7Sb₂Te₃三元靶材的存在状态。结果表明：Al掺杂后,靶材主相Sb₂Te₃的晶格常数减小,且单质Al弥散相与Al_0.1Sb₂Te₃基体相共存,表明掺杂对靶材的组织结构确有影响;刻蚀深度从0增加至405.9nm,Al价态从以Al₂O₃的化合态为主逐渐过渡至以单质态为主,且Al以Al₂O₃形态为主的区域深度约90nm;刻蚀深度为405.9nm时,来自非氧化物的Al价态与来自AlSb的Sb价态联合表明：Al_0.1Sb₂Te₃中的Al通过有效化合形成AlSb影响着靶材的组织结构。     

性能优异的SrO改性Pd-Rh双金属催化剂的制备

在浸渍到Al₂O₃载体材料上之前,通过将Sr的前驱体引入到贵金属Pd和Rh的混合盐溶液中,即采用共浸渍法制备了一系列SrO改性的Pd-Rh/Al₂O₃催化剂。结果表明,由于SrO的扩散障碍效应,适量SrO（1%~2%,质量分数）的引入有利于促进Pd,Rh的分散,并且能提高催化剂的水热稳定性。水热老化之后,催化剂能保持更高的Pd,Rh分散度,并且Pd,Rh能稳定在活性更好的氧化态。因此,适量SrO改性的Pd-Rh/Al₂O₃催化剂具有更好的还原性能和三效催化活性。然而,当向催化剂中引入过量的SrO,由于SrO占据了过量的Al₂O₃的表面,而且老化后会出现新的物相SrAl₂O₄,反而会对催化剂的性能产生不利的影响。总的来说,2% SrO改性的催化剂具有最优异的三效催化活性,水热老化之后,相比于空白的Pd-Rh/Al₂O₃催化剂,2%SrO改性的催化剂使CO,HC和NO的起燃温度分别降低了23,15和27 ℃。     

Investigation on the corrosion and oxidation resistance of Ni-Al2O3 nano-composite coatings prepared by sediment co-deposition

Ni-Al₂O₃ composite coatings were prepared by using sediment co-deposition (SCD) technique from a Watt's type electrolyte containing nano-Al₂O₃ particles. The corrosion resistance and high temperature oxidation resistance of resulting composite coatings were investigated. It was found that the incorporation of nano-Al₂O₃ particles in Ni matrix refined the Ni crystal and changed the preferential orientation of composite coatings. Meanwhile, the corrosion and oxidation resistance were improved after the incorporation of nano-Al₂O₃ particles into Ni matrix. The nano-Al₂O₃ content in deposits plays an important role for improving the corrosion and oxidation protection. The corrosion and oxidation resistance of Ni-Al₂O₃ nano-composite coatings produced via SCD technique are superior to that of CEP technique. Compared to pure Ni and Ni-Al₂O₃ composite coatings fabricated using CEP technique, the Ni-7.58 wt.% Al₂O₃ composite coating obtained by SCD technique exhibits better corrosion resistance and enhanced high temperature oxidation resistance. Moreover, the mechanism of corrosion and high temperature oxidation resistance of Ni-Al₂O₃ nano-composite coatings are discussed.     

Synthesis and characterization of Al2O3-Ce0.5Zr0.5O2 powders prepared by chemical coprecipitation method

Al₂O₃-Ce_0.5Zr_0.5O₂ catalytic powders were synthesized by the coprecipitation (ACZ-C) and mechanical mixing (ACZ-M) methods, respectively. As-synthesized powders were characterized by XRD, Raman spectroscopy, surface area and thermogravimetric analyses. It was found that the mixing extent of Al³⁺ ions affected the phase development, texture and oxygen storage capacity (OSC) of the Ce_0.5Zr_0.5O₂ powder. Single phase of ACZ-C could be maintained without phase separation and inhibit α-Al₂O₃ formation up to 1200 °C. The specific surface area value of ACZ-C (81.5 m²/g) was larger than that of ACZ-M (62.1 m²/g) and Ce_0.5Zr_0.5O₂ (17.1 m²/g) powders, which were calcined at 1000 °C. In comparison with ACZ-C and Al₂O₃, which were calcined at high temperature (900–1200 °C), it was found that the degradation rate of specific surface area of ACZ-C was lower than that of Al₂O₃. ACZ-C sample showed a higher thermal stability to resist phase separation and crystallite growth, which enhanced the oxygen storage capacity property for Ce_0.5Zr_0.5O₂ powders.     

Oxidation behavior of micro-sized Al2O3–TiC–Co composites prepared from cobalt-coated powders

The oxidation behavior of hot-pressed Al₂O₃–TiC–Co composites prepared from cobalt-coated powders has been studied in air in the temperature range from 200 °C to 1000 °C for 25 h. The oxidation resistance of Al₂O₃–TiC–Co composites increases with the increase of sintering temperature at 800 °C and 1000 °C. The oxidation surfaces were studied by XRD and SEM. The oxidation kinetics of Al₂O₃–TiC–Co composites follows a rate that is faster than the parabolic-rate law at 800 °C and 1000 °C. The mechanism of oxidation has been analyzed using thermodynamic and kinetic considerations.     

Toughening and strengthening mechanism of plasma sprayed nanostructured Al2O3–13 wt.%TiO2 coatings

The starting materials of Al₂O₃, TiO₂, ZrO₂ and CeO₂ nanoparticles were agglomerated into sprayable feedstock powders and plasma sprayed to form nanostructured coatings. There were net structures and fused structures in plasma sprayed nanostructured Al₂O₃–13 wt.%TiO₂ coatings. The net structures were derived from partially melted feedstock powders and the fused structures were derived from fully melted feedstock powders. The nanostructured Al₂O₃–13 wt.%TiO₂ coatings possessed higher hardness, bonding strength and crack growth resistance than conventional Metco 130 coatings which were mainly composed of lamellar fused structures. The higher toughness and strength of nanostructured Al₂O₃–13 wt.%TiO₂ coatings were mainly related to the obtained net structures.     

Synthesis and characterization of Y3Al5O12 and ZrO2-Y2O3 thermal barrier coatings by combustion spray pyrolysis

Y₃Al₅O₁₂ and ZrO₂-Y₂O₃ (8 mol% YSZ) coatings for potential application as thermal barrier coatings were prepared by combustion spray pyrolysis. Thermal cycling of as deposited coatings on stainless steel and FeCrAlY bond coat substrates was carried out at 1000 °C and 1200 °C to determine the thermal fatigue response. Structural and morphological studies on Y₃Al₅O₁₂ and 8 mol% YSZ coatings before and after thermal cycling have been carried out. It has been noted that the coatings on FeCrAlY substrates remain intact after 50 cycles between room temperature and 1200 °C, whereas the coatings on stainless steel show some minor damage such as peeling off near the periphery after 50 cycles at 1000 °C. Thermal diffusivity values of Y₃Al₅O₁₂ and 8 mol% YSZ films were measured by using photo thermal deflection spectroscopy and the values are lower than those of coatings produced by conventional techniques such as EBPVD and APS.     

Oxidation behavior of Ti3AlC2 at 1000-1400 °C in air

The isothermal oxidation behavior of bulk Ti₃AlC₂ has been investigated at 1000-1400 °C in air for exposure times up to 20 h by means of TGA, XRD, SEM and EDS. It has been demonstrated that Ti₃AlC₂ has excellent oxidation resistance. The oxidation of Ti₃AlC₂ generally followed a parabolic rate law with parabolic rate constants, k_p that increased from 4.1×10⁻¹¹ to 1.7×10⁻⁸ kg² m⁻⁴ s⁻¹ as the temperature increased from 1000 to 1400 °C. The scales formed at temperatures below 1300 °C were dense, adherent, resistant to cyclic oxidation and layered. The inner layer of these scales formed at temperatures below 1300 °C was continuous α-Al₂O₃. The outer layer changed from rutile TiO₂ at temperatures below 1200 °C to a mixture of Al₂TiO₅ and TiO₂ at 1300 °C. In the samples oxidized at 1400 °C, the scale consisted of a mixture of Al₂TiO₅ and, predominantly, α-Al₂O₃, while the adhesion of the scales to the substrates was less than that at the lower temperatures. Effect of carbon monoxide at scale/substrate was involved in the formation of the continuous Al₂O₃ layers.     

Role of Al2O3 layer in oxidation resistance of Cu-Al dilute alloys pre-annealed in H2 atmospheres

Copper was alloyed with small amounts of Al (0.2, 0.5, 1.0 and 2.0 mass%) to improve the oxidation resistance. Copper (6 N) and the Cu-Al alloys were oxidized at 773-1173 K in 0.1 MPa oxygen atmosphere after hydrogen annealing at 873 K. Continuous very thin Al₂O₃ layers were formed on the surface of all Cu-Al dilute alloys during the hydrogen annealing. Oxidation resistance of Cu-Al alloys was improved especially for Cu-2.0Al at 773-973 K, while it decreases on increasing the oxidation temperature. Cu-Al alloys followed the parabolic rate law at 1173 K, but most of other cases do not at and below 1073 K. Oxidation resistance for Cu-Al alloys was found relevant to the maintenance of the thin Al₂O₃ layer at the Cu₂O/Cu-Al alloy interface.     

304不锈钢表面Ni-Al2O3复合镀层制备及性能研究

采用复合电沉积法在304奥氏体不锈钢表面制备Ni-Al₂O₃纳米镀层. 研究了Al₂O₃颗粒在复合镀层中的分布情况, 确定了镀液中颗粒的最佳加入量、最佳电流强度和最佳搅拌速度. 用扫描电镜和能谱仪、X射线衍射仪等设备鉴定镀层显微组织与组成. 结果表明, Ni-Al₂O₃纳米复合镀层均匀、致密、晶粒细小; 复合镀层结合强度、耐腐蚀性能优良, 抗高温氧化性能优于纯镍镀层.     

Ti6Al4V钛合金表面Al2O3颗粒改性微弧氧化涂层制备及性能

微弧氧化技术是一门新的表面处理技术,在很多领域有着广泛的应用前景,但其结构受限于电解液成分。本文通过在磷酸盐电解液中加入Al2O3陶瓷颗粒,使得在Ti6Al4V钛合金表面的微弧氧化涂层结构和性能得到改性。涂层的结构和性能通过扫描电镜和XRD衍射仪进行表征和测试,涂层的抗高温氧化性能和热震性能通过高温热循环氧化试验和热震试验进行测试。结果表明,通过在电解液中添加Al2O3陶瓷颗粒,涂层由Al2TiO5 and TiO2组成,涂层更为致密,表现出更为优异的抗高温氧化和热震性能。电解液中游动的Al2O3陶瓷颗粒在微弧氧化过程中被吸入到样品表面并进入涂层,涂层的结构和性能得到改性。     

Cyclic oxidation behavior and thermal barrier effect of YSZ-(Al2O3/YAG) double-layer TBCs prepared by the composite sol-gel method

Novel YSZ (6 wt.% yttria partially stabilized zirconia)-(Al₂O₃/YAG) (alumina-yttrium aluminum garnet, Y₃Al₅O₁₂) double-layer ceramic coatings were fabricated using the composite sol-gel and pressure filtration microwave sintering (PFMS) technologies. The thin Al₂O₃/YAG layer had good adherence with substrate and thick YSZ top layer, which presented the structure of micro-sized YAG particles embedded in nano-sized α-Al₂O₃ film. Cyclic oxidation tests at 1000 °C indicated that they possessed superior properties to resist oxidation of alloy and improve the spallation resistance. The thermal insulation capability tests at 1000 °C and 1100 °C indicate that the 250 μm coating had better thermal barrier effect than that of the 150 μm coating at different cooling gas rates. These beneficial effects should be mainly attributed to that, the oxidation rate of thermal grown oxides (TGO) scale is decreased by the “sealing effect” of α-Al₂O₃, the “reactive element effect”, and the reduced thermal stresses by means of nano/micro composite structure. This double-layer coating can be considered as a promising TBC.