Seismic response of isolated bridges with soil–structure interaction

The modern transportation facilities demand that the bridges are to be constructed across the gorges that are located in seismically active areas and at the same time the site conditions compel the engineers to rest the pier foundation on soil. The purpose of this study is to assess the effects of soil–structure interaction (SSI) on the peak responses of three-span continuous deck bridge seismically isolated by the elastomeric bearings. The emphasis has been placed on gauging the significance of physical parameters that affect the response of the system and identify the circumstances under which it is necessary to include the SSI effects in the design of seismically isolated bridges. The soil surrounding the foundation of pier is modelled by frequency independent coefficients and the complete dynamic analysis is carried out in time domain using complex modal analysis method. In order to quantify the effects of SSI, the peak responses of isolated and non-isolated bridge (i.e. bridge without isolation device) are compared with the corresponding bridge ignoring these effects. A parametric study is also conducted to investigate the effects of soil flexibility and bearing parameters (such as stiffness and damping) on the response of isolated bridge system. It is observed that the soil surrounding the pier has significant effects on the response of the isolated bridges and under certain circumstances the bearing displacements at abutment locations may be underestimated if the SSI effects are not considered in the response analysis of the system.     

Dynamic analysis of train–bridge system subjected to non‐uniform seismic excitations

Based on the theory of dynamic wheel–rail interactions, a dynamic model of coupled train–bridge system subjected to earthquakes is established, in which the non‐uniform characteristics of the seismic wave input from different foundations are considered. The bridge model is based on the modal comprehension analysis technique. Each vehicle is modelled with 31 degrees of freedom. The seismic loads are imposed on the bridge by using the influence matrix and exerted on the vehicles through the dynamic wheel–rail interaction relationships. The normal wheel–rail interaction is tackled by using the Hertzian contact theory, and the tangent wheel–rail interaction by the Kalker linear theory and the Shen–Hedrick–Elkins theory. A computer code is developed. A case study is performed to a continuous bridge on the planned Beijing–Shanghai high‐speed railway in China. Through input of typical seismic waves with different propagation velocities to the train–bridge system, the histories of the train running through the bridge are simulated and the dynamic responses of the bridge and the vehicles are calculated. The influences of train speed and seismic wave propagation velocity on the dynamic responses of the bridge–vehicle system are studied. The critical train speeds are proposed for running safety on high‐speed railway bridges under earthquakes of various intensities. Copyright © 2006 John Wiley & Sons, Ltd.     

Soil–structure interaction analysis of cable-stayed bridges for spatially varying ground motion components

In this study, it is intended to determine the effects of soil–structure interaction (SSI) and spatially varying ground motion on the dynamic characteristics of cable-stayed bridges. For this purpose, ground motion time histories are simulated for spatially varying ground motions, depending on its components of incoherence, wave-passage and site-response effects. The substructure method, which partitions the total soil–structure system into the structural system and the soil system, is used to treat the soil–structure interaction problem. To emphasize the relative importance of the spatial variability effects of earthquake ground motion, bridge responses are determined for the fixed base bridge model, which neglects the soil–structure interaction (no SSI) and for the bridge model including the soil–structure interaction (SSI). This parametric study concerning the relative importance of the soil–structure interaction and spatially varying ground motion shows that these effects should be considered in the dynamic analyses of cable-stayed bridges.     

列车引起的地基土应力状态变化的三维有限元分析

将列车移动荷载简化为多个移动轮轴荷载,基于列车-轨道-路基解析模型推求的列车运行时不同时刻、不同位置时作用于路基的振动荷载时程,采用多点输入方式实现列车荷载的移动施加方式,建立路(地)基-场地体系三维有限元动力分析模型,基于Abaqus软件的并行计算集群平台,对轨道交通振动荷载下路(地)基-场地体系的动力反应进行数值模拟,研究了列车荷载作用线正下方地基中的动应力特征及土单元应力状态变化,分析了列车轮轴荷载移动过程中不同深度处土单元的应力路径和主应力轴的旋转。     

Extending the application of integral frame abutment bridges in earthquake‐prone areas by using novel isolators of recycled materials

Integral abutment bridges (IABs) are jointless structures without bearings or expansion joints which require minimum or zero maintenance. The barrier to the application of long‐span integral abutment bridges is the interaction of the abutment with the backfill soil during the thermal expansion and contraction of the bridge deck, that is, serviceability, or when the bridge is subjected to dynamic loads, such as earthquakes. The interaction of the bridge with the backfill leads to settlements and ratcheting of the soil behind the abutment and, as a result, the soil pressures acting on the abutment build up in the long term. This paper provides a solution for the aforementioned challenges by introducing a novel isolator that is a compressible inclusion of reused tyre‐derived aggregates placed between the bridge abutment and the backfill. The compressibility of typical tyre‐derived aggregates was measured by laboratory tests, and the compressible inclusion was designed accordingly. The compressible inclusion was then applied to a typical integral frame abutment model, which was subjected to static and dynamic loads representing in‐service and seismic loads correspondingly. The response of both the conventional and the isolated abutment was assessed based on the settlements of the backfill, the soil pressures and the actions of the abutment. The study of the isolated abutment showed that the achieved decoupling of the abutment from the backfill soil results in significant reductions of the settlements of the backfill and of the pressures acting on the abutment. Hence, the proposed research enables extending the length limits of integral frame bridges subjected to earthquake excitations. Copyright © 2016 John Wiley & Sons, Ltd.     

Seismic behavior of a post-tensioned integral bridge including soil–structure interaction (SSI)

Current practice usually pays little attention to the effect of soil–structure interaction (SSI) on seismic analysis and design of bridges. The objective of this research study is to assess the significance of SSI on the modal with geometric stiffness and seismic response of a bridge with integral abutments that has been constructed using a new bridge system technology. Emphasis is placed on integral abutment behavior, since abutments together with piers are the most critical elements in securing the integrity of bridge superstructures during earthquakes. Comparison is made between analytical results and field measurements in order to establish the accuracy of the superstructure–abutment model. Sensitivity studies are conducted to investigate the effects of foundation stiffness on the overall dynamic and seismic response of the new bridge system.     

基于模糊理论的高铁连续梁桥地震风险评估

以某高速铁路线上一座连续梁桥为例,运用模糊综合评判法,结合基于位移的支座损伤分析和截面曲率的桥墩损伤分析,以全概率理论地震损失模型为基础,提出了基于模糊理论的桥梁系统地震经济风险评估方法。结果表明:综合考虑桥梁系统的模糊地震经济风险分析方法能更全面地计算出连续梁桥在地震作用下的经济损失,仅以桥墩构件代表全桥所得地震经济损失误差较大。基于模糊理论的年预期损失风险框架方法通过结构抗震性能的概率特征可对高速铁路连续梁桥的地震直接经济风险进行全面评估,为该类桥梁的抗震设计、维修加固和灾后重建等方案做出合理评价。     

铁路大跨度简支钢桁梁桥车-桥耦合振动研究

桥梁作为线路工程中不可或缺的重要枢纽,对列车通过桥梁时,桥梁和车辆之间相互作用的问题迫切需要做出解答,特别是针对铁路钢桁梁,并考虑大跨度简支特性的车-桥耦合振动问题研究更具有一定的理论与实际意义。以黄韩侯铁路新黄河特大桥156 m简支钢桁梁桥作为工程背景,建立车辆动力模型、桥梁有限元模型并考虑轮轨关系,以蛇形运动和轨道不平顺作为系统的自激激励源,利用大型有限元软件ANSYS以及UM(Universal Mechanism)动力学分析软件联合进行仿真分析,实现单个机车、编组客车和编组货车以设计时速通过桥梁时对大跨度简支钢桁梁桥车-桥耦合振动的研究。经过计算分析得出:大跨度钢桁梁桥的横向刚度相对较小;不同编组情况以设计时速通过桥梁时,车辆和桥梁的各项动力响应参数均在规范允许的范围之内;编组货车通过桥梁时,桥梁跨中横向、竖向加速度较之其他编组情况要大。     

A semi-analytical approach for analyzing ground vibrations caused by trains moving over elevated bridges

A semi-analytic approach is presented for the three-dimensional analysis of ground vibrations induced by trains moving over elevated bridges. The train is modeled as two sets of moving loads, with one for the front wheels and the other for the rear ones, the elevated bridge as a series of elastically supported beams, and the ground as a viscoelastic half space. Three key elements are considered in the solution: (1) the analytic solution for the vibration of an elastically supported beam under a series of moving loads, (2) the impedance of the foundation–soil system, and (3) Green's function for an elastic half space under a harmonic point load. Such an approach allows us to consider the structural dynamics of the elevated bridge, the foundation–soil interaction, and the wave propagation characteristics in the half space. From the numerical examples studied, the proposed approach was demonstrated to be accurate and efficient. The framework of analysis described herein can be generalized to solve problems with complex foundations and layered soils.     

设置限位器双向隔震铁路桥梁车桥耦合动力响应研究

对铅芯橡胶双向隔震铁路桥梁在列车荷载作用下的力学性能进行了研究,针对双向隔震铁路桥梁中存在的问题,提出了设置限位器的解决方案,并对设置限位器的双向隔震铁路桥梁进行了车桥耦合动力响应分析。研究结果表明,采用常规隔震设计方法的铅芯橡胶支座在横桥向的初始刚度和屈服强度均不能满足规范要求,设置限位器后,双向隔震铁路桥梁的力学性能有了很大的改善,各项指标均满足列车运行安全性和平稳性要求。     

无缝桥抗震性能的对比研究

本文以一座三跨总长60 m的整体桥为案例桥,分别试设计了同跨径的半整体桥、延伸桥面板桥和常规连续梁桥。通过Midas/Civil软件建立四种桥型的有限元模型,并对其进行了E1和E2反应谱分析和时程分析,对比了四种桥型的结构反应峰值（墩顶位移、桥墩及桩基剪力与弯矩、台底位移、桥台桩基剪力与弯矩）。计算结果表明:当桥梁存在15°的斜交角,整体桥、半整体桥在地震动沿平行于桥台长边方向及其垂直方向输入时更不利,而延伸桥面板桥和常规连续梁桥在地震动沿顺桥向和横桥向输入时更不利。四种桥型在地震作用下:整体桥抗震性能最优异,但其台底位移、桥台桩基的剪力和弯矩最大;半整体桥台底位移、桥台桩基的剪力和弯矩最小,其墩顶位移、桥墩及桩基的剪力和弯矩仅比整体桥大;延伸桥面板桥和常规连续梁桥的墩-梁相对位移远大于整体桥和半整体桥,不适用于地震基本烈度高的区域。     

Evaluation of substructuring method for seismic soil-structure interaction analysis of bridges

This paper evaluates the commonly used substructuring method for analysis of bridge systems where the bridge is divided into two sub-systems: the bridge superstructure and the substructure including the pile foundations, abutments, and soil. Modeling of the soil-structure interaction (SSI) in the system is simplified by replacing the pile foundations, abutments, and soil with sets of independent equivalent linear springs and dashpots at the base of the superstructure. The main objective of the paper is to examine how well the substructuring method simulates the seismic response of a bridge system. The baseline data required for the evaluation process is derived from analyzing a fully-coupled continuum bridge model, already validated for the instrumented two-span Meloland Road Overpass. The same bridge system is also simulated using the substructuring method. The results from both approaches are compared, and it is shown that the differences between them can be significant. The substructuring method consistently overestimates the pier base shear forces and bending moments and the pier top deflections. Moreover, the spectral response of the bridge structure is mispredicted. The analyses are repeated for a three-span bridge system subjected to several ground motions, leading to a similar observation as before. Hence, the current state of practice for simulating seismic SSI in bridges using the substructure model is shown to be too simplified to capture the major mechanisms involved in SSI.     

Identification of soil–structure interaction effect in base-isolated bridges from earthquake records

Identification of system parameters with the help of records made on base-isolated bridge during earthquakes provides an excellent opportunity to study the performance of the various components of such bridge systems. Using a two-stage system identification methodology for non-classically damped systems, modal and structural parameters of four base-isolated bridges are reliably identified using acceleration data recorded during 18 earthquakes. Physical stiffness of reinforced concrete columns, dynamic properties of soil and foundation impedance are found by available theoretical models in conjunction with pertinent information from the recorded accelerographs. Soil–structure interaction (SSI) effect in these bridges is examined by comparing the identified and physical stiffness of the sub-structure components. It is found that SSI is relatively pronounced in bridges founded in weaker soils and is more strongly related to the ratio of pier flexural stiffness and horizontal foundation stiffness than soil shear modulus, G_s, alone. However, substantial reduction in G_s is observed for moderate seismic excitation and this effect should be taken into account while computing foundation impedance.     

大跨铁路钢桁连续梁桥减隔震方案比较研究

为研究适用于大跨铁路钢桁连续梁桥的减隔震方案及合理优化参数,以一座全长504 m的三跨铁路钢桁连续梁特大桥为工程背景,使用非线性结构分析软件SAP2000建立有限元模型,采用快速非线性分析方法分析对比摩擦摆、阻尼器、速度锁定器等减隔震方案在各种装置参数下的减震效率。研究表明:由于大跨铁路钢桁连续梁桥墩身自振导致的地震力较大,摩擦摆方案内力减震效率一般,同时墩底内力对滑动面半径变化并不敏感,在选取滑动半径时应更多地考虑行车平顺性和梁端位移值的限制。速度锁定器会极大地增加此类桥梁地震输入能量,不适用于此类桥型。阻尼器方案对活动墩内力减震效果明显,但不能有效降低固定墩内力。摩擦摆支座附加阻尼器组合减震方案能有效控制此类桥梁的内力和位移响应。研究结论可为大跨度钢桁连续梁桥减隔震设计提供参考。     

Dynamic soil–structure interaction effects on the seismic response of suspension bridges

A stochastic approach has been formulated for the linear analysis of suspension bridges subjected to earthquake excitations. The transfer functions of various responses have been formulated while including the effects of dynamic Soil–Structure Interaction (SSI) via the use of the fixed-base modes of the structure. The excitation has been characterized by the ‘equivalent stationary’ processes corresponding to the free-field motions at each support and by an assumed coherency function between these motions. The proposed formulation considers the non-stationarity in the structural response due to sudden application of excitation by considering (i) the time-dependent frequency response functions, and (ii) the order statistics formulation for the peak factors in evolutionary response processes. The formulation has been illustrated by analysing the seismic response of the Golden Gate Bridge at San Francisco for two example excitations conforming to USNRC-specified design spectra. The significance of various governing parameters on the dynamic soil–structure interaction effects on the seismic response of suspension bridges has also been studied. It has been found that the contribution of the vertical component of ground motion to the bridge response increases with increasing soil compliance. Also, the extent to which the spatial variation of ground motion affects the bridge response depends on how significant the SSI effects are. Copyright © 1999 John Wiley & Sons Ltd.     

Full-scale model testing on a ballastless high-speed railway under simulated train moving loads

Model testing in laboratory, as an effective alternative to field measurement, provides valuable data to understand railway׳s dynamic behaviors under train moving loads. This paper presents comprehensive experimental results on track vibration and soil response of a ballastless high-speed railway from a full-scale model testing with simulated train moving loads at various speeds. A portion of a realistic ballastless railway comprising slab track, roadbed, subgrade, and subsoil was constructed in a larger steel box. A computer-controlled sequential loading system was developed to generate equivalent vertical loadings at the track structure for simulating the dynamic excitations due to train׳s movements. Comparisons with the field measurements show that the proposed model testing can accurately reproduce dynamic behaviors of the track structure and underlying soils under train moving loads. The attenuation characteristics of dynamic soil stresses in a ballastless slab track is found to have distinct differences from that in a ballasted track. The model testing results provide better understanding of the influence of dynamic soil–structure interaction and train speed on the response of track structure and soils.     

模块化预制拼装铁路实心桥墩抗震性能数值分析

为适应施工期短的严/高寒地区和近海铁路桥梁工程发展,提高铁路桥梁工程的施工效率和工程质量.文中提出了一种用于铁路桥梁工程中的模块化预制拼装实心桥墩,该桥墩不仅可以纵向节段连接,还可以通过多个可互连的模块水平连接.基于ABAQUS程序,开展了铁路桥梁模块化预制拼装桥墩在单调、往复荷载作用下力学性能数值分析,对该桥墩的承载...     

Effect of train dynamics on seismic response of steel monorail bridges under moderate ground motion

This study is intended to investigate the seismic response of steel monorail bridges using three‐dimensional dynamic response analysis. We particularly consider monorail bridge–train interaction when subjected to ground motion that occurs with high probability. A monorail train car with two bogies with pneumatic tires for running, steering and stabilizing wheels is assumed to be represented sufficiently by a discrete rigid multi‐body system with 15 degrees of freedom (DOFs). Bridges are considered as an assemblage of beam elements with 6 DOFs at each node. Modal analysis is used for dynamic response analysis under moderate earthquakes. The seismic response of an advanced monorail bridge that adopts a simplified structural system and composite girders is investigated through comparison with seismic responses of a conventional bridge. The acceleration response of a monorail train is also calculated to investigate the effect of structural types of bridges on the train's dynamic response during earthquakes. Results show that the seismic responses of the advanced bridges are greater than those of the conventional monorail bridge because of the simplified structural system and increased girder weight that is attributable to composite girders of the advanced bridge. Moreover, the train on the advanced bridge shows greater dynamic response than that on the conventional bridge. Observations reveal that the dynamic monorail train system acts as a damper on the monorail bridge. That fact shows that the existing design, which considers a train as additional mass, yields a conservative result. Copyright © 2006 John Wiley & Sons, Ltd.