共查询到20条相似文献,搜索用时 656 毫秒
1.
针对原油性质变化对常减压装置操作造成的巨大困难,提出了一种稳定原油性质和引入原油性质参数到软测量和控制模型的先进控制综合解决方案。一方面,对待混炼的多种原油进行调度和掺炼比优化,使实际进入常减压装置进行炼制的调合原油性质相对稳定,装置操作参数变化较小,减少工作点大幅变化过程中所产生的波动。另一方面,针对仍然存在的原油性质小幅度变化,在软测量和预测控制建模中引入反映原油性质的馏程参数,克服原油性质变化所引起的扰动。现场实际装置的应用结果说明了此综合方案的有效性。 相似文献
2.
3.
绪言作为化学工程单元操作的混炼技术,可在橡胶、塑料、油墨、涂料等化学工业看到其发展的历史。新型连续混炼装置(KCK),为笔者长期从事混炼装置设计的经验总结,并以诸前辈开发优良的混炼装置之混炼结构原理为基础,面向未来而构思开发的连续混炼机。 相似文献
4.
5.
6.
随着石油的开采及炼化,高品质原油的进一步消耗,大多炼厂不得不改炼或混炼劣质化原油,原油的劣化对生产装置及生产安全造成一定程度的影响。本文针对炼油第一道工序常减压蒸馏装置的腐蚀影响因素进行了分析,重点分析了盐含量、硫含量及环烷酸的影响。并针对常减压炼油装置的腐蚀现状,从加强工艺防腐、做好腐蚀监测管理及合理选材等几个方面介绍了当前常减压装置的腐蚀控制措施,为炼油设备的长期稳定安全有效运行提供一定参考。 相似文献
7.
介绍了以8031单片机为主体研制的开炼机混炼过程微机控制装置。该装置采用大屏幕汉字显示,在混炼过程中按混炼工艺顺序指导工人生产,同时还实现了对辊温、辊距等工艺参数的自动控制,每年可节电30000度。 相似文献
8.
HDPE/mLLDPE混炼后的性能与结构 总被引:1,自引:0,他引:1
高密度聚乙烯/茂金属线性低密度聚乙烯(HDPE/mLLDPE)40/60共混物经混炼器混炼后的冲击强度比未经混炼器混炼的HDPE增加了96.2%,比未经混炼器混炼的mLLDPE增加了27.0%,其拉伸强度比未经混炼器的mLLDPE增加了49.1%。这表明在混炼器的强剪切分散作用下,HDPE,mLLDPE共混对HDPE和mLLDPE有显著的增韧作用。其微观结构测试表明,mLLDPE与HDPE形成了共晶结构,HDPE含量高的HDPE/mLLDPE共混体系试样内部的晶粒尺寸更为均一。 相似文献
9.
常减压装置高酸原油的腐蚀和防治 总被引:1,自引:0,他引:1
结合中石化金陵分公司炼制高酸原油的实际情况,分析了常减压装置的主要腐蚀类型和腐蚀机理,并在此基础上提出了具体的防治措施:混炼、控制流速和流态、注意选材、工艺防腐措施等。实践证明这些措施取得了较好的防腐效果。 相似文献
10.
11.
以乙烯装置的离线模拟系统和合成氨装置的在线模拟系统为例,分析探讨了离、在线模拟系统的功能特点差异,以及系统中数据校正模型、基础工况模型的开发技术及应用效果。 相似文献
12.
A hybrid neural network model based on‐line reoptimization control strategy is developed for a batch polymerization reactor. To address the difficulties in batch polymerization reactor modeling, the hybrid neural network model contains a simplified mechanistic model covering material balance assuming perfect temperature control, and recurrent neural networks modeling the residuals of the simplified mechanistic model due to imperfect temperature control. This hybrid neural network model is used to calculate the optimal control policy. A difficulty in the optimal control of batch polymerization reactors is that the optimization effort can be seriously hampered by unknown disturbances such as reactive impurities and reactor fouling. With the presence of an unknown amount of reactive impurities, the off‐line calculated optimal control profile will be no longer optimal. To address this issue, a strategy combining on‐line reactive impurity estimation and on‐line reoptimization is proposed in this paper. The amount of reactive impurities is estimated on‐line during the early stage of a batch by using a neural network based inverse model. Based on the estimated amount of reactive impurities, on‐line reoptimization is then applied to calculate the optimal reactor temperature profile for the remaining time period of the batch reactor operation. This approach is illustrated on the optimization control of a simulated batch methyl methacrylate polymerization process. 相似文献
13.
14.
提出一个粗糙表面上移动接触线和动态接触角的数理模型:毛细数较低时表观接触线前缘存在极薄的前驱膜,表观接触线在“湿”固体表面上移动,不同于传统模型中认为表观接触线在“干”固体表面上移动.在Moffatt角区内部流动解的基础上,通过引入接触线特征参数表征表观接触线在前驱膜上的滑移程度,导出动态接触角的速度关系.与不同研究者实验数据对比发现量纲1特征参数反映固体材料特性和表面特性对动态湿润过程的影响,与液相的性质无关.结合前期提出的滞后张力模型,对动态法和静态法测量静接触角产生的差异给出合理解释. 相似文献
15.
A new way of applying on‐line experimental data and basic theory to study the mechanism of orientation of a high‐speed melt spinning process is described. The relationship of birefringence and stress for Nylon‐66 was developed to understand the phenomena in the spinning line. The value of birefringence along the spinning line was calculated by various models to predict the orientation change. By comparison of the model prediction and on‐line experimental birefringence, a suitable mechanical model to simulate the change of the profiles along the spinning line was chosen, and the structural development mechanism is discussed. The results show that the orientation mechanism of high‐speed melt spinning of Nylon‐66 is determined by deformation and deformation rate along the spinning line. For Nylon‐66, molecular and crystal orientations develop independently and are controlled by the rotation of crystals and chain segments in the deformation field. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3157–3163, 2001 相似文献
16.
流线型挤出模参数化建模方法研究 总被引:1,自引:0,他引:1
在编程实现对型材截面轮廓凸凹性自动判断的基础上,采用射线法与比例间隔法相结合的方法,确定流道人口圆周上型值点的位置,以三次多项式作为流道模腔型曲线的数学模型,依据流线型要求给出的初始、边界条件得出型曲线的数学方程,构建了挤出模流道的三维参数化模型,为挤出模CAD/CAE的双向集成技术研究奠定基础。数值分析结果显示,该方法创建的流线型流道模型,其流动稳定性和平顺性都优于直线型流道。 相似文献
17.
以聚酯缩聚反应过程为对象,用发生函数法建立在线相对分子质量分布估计模型。为了符合缩聚釜的实际效应,采用有约束优化方法在线校正模型参数,并用现场数据进行仿真计算。仿真结果表明,本模型预估的MWD在正常工况下与工厂设计数据吻合,并能不断给出整个缩聚流程的质量信息,对聚酯缩聚过程相对分子质量分布进行预估是有效的。 相似文献
18.
A model based on linear elasticity is presented describing the stresses arising during the processing of polymeric films on tenter frames. The model demonstrates that large in-plane shear stresses, resulting from gradients in the line, produce anisotropic stresses in the film. The magnitude of the anisotropy is found to vary transversely across the line, becoming isotropic in the center and achieving maximum values at the edges of the line. The principal directions of the stress tend to lie at ±45° to the machine direction but may be altered by machine and transverse drawing by the frame. These results agree with orientation measurements reported in the literature on polyimide films produced on tentering frames. 相似文献
19.
针对目前汽车生产线需新老产品混线生产,而原有橇体机构无法实现的状况,通过对新老产品的底部结构数模进行分析研究,设计出一款新型多功能橇体。介绍了该橇体的设计实施过程、结构组成、工作原理及相关技术要求等。 相似文献