Synthesis of boron modified CoMo/Al2O3 catalyst under different heating methods and its gasoline hydrodesulfurization performance

Catalytic hydrodesulfurization (HDS) technique is widely used for clean gasoline production. However, traditional HDS catalyst (CoMo/γ-Al₂O₃) exhibits high hydrogenation performance of olefins (HYDO), resulting in the loss of gasoline octane number. To achieve high HDS/HYDO ratio, the key issue is to reduce the interaction between active metals and the support, therefore, in this research, the modified CoMo/γ-Al₂O₃ catalysts with various boron amounts were investigated under traditional or microwave heating. The effects of preparing methods as well as boron amounts on the active phase, acidic properties and HDS catalytic activities were examined. Results show that the modification, especially under microwave treatment, can significantly weaken the interaction between the active component and the support by enlarging the surface area and pore diameter, and reducing the acidity of the support. As a result, the stacking numbers of MoS₂ slabs were obviously improved by the modification and microwave treatment, contributing to higher edge/rim ratio, and resulting in higher HDS performance and selectivity to olefin.     

Hydrogenation of naphthalene on NiMo- Ni- and Ru/Al2O3 catalysts: Langmuir–Hinshelwood kinetic modelling

The importance of the hydrodearomatisation (HDA) is increasing together with tightening legislation of fuel quality and exhaust emissions. The present study focuses on hydrogenation (HYD) kinetics of the model aromatic compound naphthalene, found in typical diesel fraction, in n-hexadecane over a NiMo (nickel molybdenum), Ni (nickel) and Ru (ruthenium) supported on trilobe alumina (Al₂O₃) catalysts. Kinetic reaction expressions based on the mechanistic Langmuir–Hinshelwood (L–H) model were derived and tested by regressing the experimental data that translated the effect of both naphthalene and hydrogen concentration at a constant temperature (523.15 and 573.15 K over the NiMo catalyst and at 373.15 K over the Ni and Ru/Al₂O₃ catalysts) on the initial reaction rate. The L–H equation, giving an adequate fit to the experimental data with physically meaningful parameters, suggested a competitive adsorption between hydrogen and naphthalene over the presulphided NiMo catalyst and a non-competitive adsorption between these two reactants over the prereduced Ni and Ru/Al₂O₃ catalysts. In addition, the adsorption constant values indicated that the prereduced Ru catalyst was a much more active catalyst towards naphthalene HYD than the prereduced Ni/Al₂O₃ or the presulphided NiMo/Al₂O₃ catalyst.     

Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

Ce改性Pd基整体式催化剂的结构特征及其甲烷催化燃烧性能

分别以拟薄水铝石和添加Ce的拟薄水铝石制备铝溶胶,经过堇青石（Cord）表面涂覆和Pd溶液浸渍,得到浸渍法和溶胶法Ce改性的Pd/γ-Al₂O₃/Cord整体式催化剂。采用XRD、SEM和XPS等对催化剂进行表征,评价其甲烷催化燃烧反应性能,并考察Ce的不同添加方式对催化剂结构和反应性能的影响。结果表明,适量Ce的添加可提高Pd基整体式催化剂的甲烷催化燃烧性能,溶胶法优于浸渍法。随着Ce添加量的增加,浸渍法改性的Pd基催化剂催化性能有所降低,溶胶法则呈现先升高后降低的趋势。溶胶法中Ce的添加物与γ-Al₂O₃涂层充分融合,提高了涂层的热稳定性和活性组分的分散度,0.5Pd/γ-Al₂O₃(3.0Ce)/Cord催化剂催化性能最优。     

The role of molybdenum in Mo-doped V–Mg–O catalysts during the oxidative dehydrogenation of n-butane

A detailed study on the influence of the addition of molybdenum ions on the catalytic behaviour of a selective vanadium–magnesium mixed oxide catalyst in the oxidation of n-butane has been performed. The catalysts have been prepared by impregnation of a calcined V–Mg–O mixed oxides (23.8 wt% of V₂O₅) with an aqueous solution of ammonium heptamolybdate, and then calcined, and further characterised by several physico-chemical techniques, i.e. S_BET, XRD, FTIR, FT-Raman, XPS, H₂-TPR. MgMoO₄, in addition to Mg₃V₂O₈ and MgO, have been detected in all the Mo-doped samples. The incorporation of molybdenum modifies not only the number of V⁵⁺-species on the catalyst surface and the reducibility of selective sites but also the catalytic performance of V–Mg–O catalysts. The incorporation of MoO₃ favours a selectivity and a yield to oxydehydrogenation products (especially butadiene) higher than undoped sample. In this way, the best catalyst was obtained with a Mo-loading of 17.3 wt% of MoO₃ and a bulk Mo/V atomic ratio of 0.6. From the comparison between the catalytic properties and the catalyst characterisation of undoped and Mo-doped V–Mg–O catalysts, the nature of selective sites in the oxidative dehydrogenation of n-butane is also discussed.     

Pt/Pt-Ce/γ-Al2O3催化氧化甲苯研究

通过等体积浸渍法制备单贵金属Pt/γ-Al₂O₃和双金属Pt-Ce/γ-Al₂O₃催化剂,考察Ce对催化剂活性的影响,确定催化剂最优配比。结果表明,当Pt的负载量为质量分数0.5%时,Pt/γ-Al₂O₃催化活性最高;当Pt的负载量为质量分数0.2%,Ce的负载量为质量分数1.0%时,Pt-Ce/γ-Al₂O₃催化剂的催化活性最高。Pt-Ce/γ-Al₂O₃催化剂的甲苯转化率高于Pt/γ-Al₂O₃催化剂。随着Pt负载量增大,催化剂孔容、孔径减小。粉体式催化剂性能优于整体式催化剂,但差别不大;Ce的添加有助于催化剂活性的提升。     

K-, CeO2-, and Mn-promoted Ni/Al2O3 catalysts for stable CO2 reforming of methane

Reforming of methane with carbon dioxide into syngas over Ni/γ-Al₂O₃ catalysts modified by potassium, MnO and CeO₂ was studied. The catalysts were prepared by impregnation technique and were characterized by N₂ adsorption/desorption isotherm, BET surface area, pore volume, and BJH pore size distribution measurements, and by X-ray diffraction and scanning electron microscopy. The performance of these catalysts was evaluated by conducting the reforming reaction in a fixed bed reactor. The coke content of the catalysts was determined by oxidation conducted in a thermo-gravimetric analyzer. Incorporation of potassium and CeO₂ (or MnO) onto the catalyst significantly reduced the coke formation without significantly affecting the methane conversion and hydrogen yield. The stability and the lower amount of coking on promoted catalysts were attributed to partial coverage of the surface of nickel by patches of promoters and to their increased CO₂ adsorption, forming a surface reactive carbonate species. Addition of CeO₂ or MnO reduced the particle size of nickel, thus increasing Ni dispersion. For Ni–K/CeO₂–Al₂O₃ catalysts, the improved stability was further attributed to the oxidative properties of CeO₂. Results of the investigation suggest that stable Ni/Al₂O₃ catalysts for the carbon dioxide reforming of methane can be prepared by addition of both potassium and CeO₂ (or MnO) as promoters.     

碱/碱土金属修饰Ni基催化剂的CO2吸附与甲烷化性能

采用分步浸渍法制备了碱/碱土金属修饰Ni基催化剂Ni-M/Al₂O₃ (M=K₂CO₃, Na₂CO₃, MgO, CaO)。探究了碱/碱土金属的添加对改性Ni基催化剂CO₂吸附和甲烷化性能的影响。研究发现,碱/碱土金属的添加提高了Ni/Al₂O₃催化剂表面的碱性活性位点密度,强化了其CO₂吸附性能。碱/碱土金属类型影响Ni-M/Al₂O₃催化剂碱性活性位点的分布、NiO物相的转化及Ni的分散度,进而影响其甲烷化性能。MgO添加使NiO物相转化为与载体呈强相互作用的β型和γ型NiO,降低了催化剂表面的强碱性活性位点比例,有利于CO₂吸附活化。Ni-MgO/Al₂O₃的CO₂吸附容量最高为0.68mmolCO₂/g,其CO₂转化率和CH₄选择性分别高达58.4%和95.4%,其在烟气CO₂捕集与原位甲烷化中极具应用前景。     

Ethanol steam reforming over Ni/La–Al2O3 catalysts: Influence of lanthanum loading

Hydrogen production from ethanol reforming over nickel catalysts supported on lanthanum loaded Al₂O₃ substrates was studied. Activity results revealed the enhancement in the reforming stability of the Ni catalysts with the increase in the lanthanum loading on Al₂O₃ substrates. Catalytic behavior of Ni/La–Al₂O₃ catalysts in the ethanol steam reforming was found to be the contribution of the activity of the La–Al₂O₃ supports for the ethanol dehydration reaction and the activity of the nickel metallic phase that catalyzes both dehydrogenation and CC bond rupture. Physicochemical characterization of catalysts revealed that acidity, nickel dispersion and nickel-support interaction depend on the La-loading on Al₂O₃. The better reforming stability of catalysts with the increase in La content was explained in terms of the ability of nickel surface and/or La–Ni interactions to prevent the formation of carbon filaments.     

Fe掺杂对Pt-Sn-K/γ-Al_2O_3异丁烷脱氢催化剂性能的影响

采用共沉淀法制备不同Fe含量的Fe(x)-γ-Al_2O_3复合氧化物载体,并采用真空浸渍法制备了Pt-Sn-K/Fe(x)-γ-Al_2O_3催化剂。对制备的催化剂进行XRD、N_2物理吸附-脱附和NH_3-TPD表征,研究Fe的掺杂对Pt-Sn-K/Fe(x)-γ-Al_2O_3催化剂的结构及其催化异丁烷脱氢反应性能的影响。结果表明,Fe的引入可以改变催化剂的反应活性和产物选择性,当Fe_2O_3掺杂质量分数为4%时,催化剂具有最高的异丁烯收率,50 h的平均收率达到42.9%。     

Ni/Al_2O_3催化剂的CO_2-TPD表征

Ni/Al_2O_3催化剂是甲烷二氧化碳重整反应制取合成气研究最多、最具应用潜力的一种催化剂。通过对催化剂进行CO_2-TPD研究,考察还原态Ni/Al_2O_3催化剂的CO_2脱附特性。结果表明,浸渍法制备的Ni/Al_2O_3催化剂CO_2脱附曲线呈现双峰,分别在(60~65)℃和(350~380)℃出现高低温两个活性位;高温CO_2吸附量为3.0 cm~3·g~(-1),低温CO_2吸附量为24.0 cm~3·g~(-1)。催化剂的CO_2吸附量与其Ni含量无关。考察选用不同载体的CO_2脱附行为,发现以Al_2O_3为载体的催化剂CO_2吸附量是MgO和SiO_2为载体催化剂的2~4倍,以TiO_2为载体的催化剂几乎不吸附CO_2。     

Promoting effect of calcium on reduction of NO by C3H6 over V2O5/ZrO2 catalysts

The reduction of nitrogen monoxide by propene on V₂O₅/ZrO₂ doped with or without calcium has been studied by FTIR spectroscopy as well as by analysis of the reaction products. Considerable promoting effect of calcium doping on the reduction of nitrogen monoxide by propene was observed on the V₂O₅/ZrO₂ catalysts. For the reaction of a mixture of NO+C₃H₆, carbonyl and carboxylate species were observed above 373 K, although nitrate species formed at room temperature on V₂O₅/ZrO₂ doped with calcium. No bands due to a compound including both carbon and nitrogen atoms were observed. Thus, the redox mechanism, i.e. propene reduces the catalyst and nitrogen monoxide oxidizes the catalyst, is confirmed on V₂O₅/ZrO₂ catalysts doped with or without calcium. The analysis of the V=O band in the region of 1100–900 cm⁻¹ indicates that this promotion is mainly due to new V=O species formed by the addition of calcium onto the catalyst. This species is easily reproduced in comparison with the other V=O species on the surface in the reoxidation process of the catalyst.     

Isomerization of n-hexane over mono- and bimetallic Pd–Pt catalysts supported on ZrO2–Al2O3–WOx prepared by sol–gel

The catalytic performance of mono- and bimetallic Pd (0.6, 1.0 wt.%)–Pt (0.3 wt.%) catalysts supported on ZrO₂ (70, 85 wt.%)–Al₂O₃ (15, 0 wt.%)–WO_x (15 wt.%) prepared by sol–gel was studied in the hydroisomerization of n-hexane. The catalysts were characterized by N₂ physisorption, XRD, TPR, XPS, Raman, NMR, and FT-IR of adsorbed pyridine. The preparation of ZrW and ZrAlW mixed oxides by sol–gel favored the high dispersion of WO_x and the stabilization of zirconia in the tetragonal phase. The Al incorporation avoided the formation of monoclinic-WO₃ bulk phase. The catalysts increased their S_BET for about 15% promoted by Al₂O₃ addition. Various oxidation states of WO_x species coexist on the surface of the catalysts after calcination. The structure of the highly dispersed surface WO_x species is constituted mainly of isolated monotungstate and two-dimensional mono-oxotungstate species in tetrahedral coordination. The activity of Pd/ZrW catalysts in the hydroisomerization of n-hexane is promoted both with the addition of Al to the ZrW mixed oxide and the addition of Pt to Pd/ZrAlW catalysts. The improvement in the activity of Pd/ZrAlW catalysts is ascribed to a moderated acid strength and acidity, which can be correlated to the coexistence of W⁶⁺ and reduced-state WO_x species (either W⁴⁺ or W⁰). The addition of Pt to the Pd/ZrAlW catalyst does not modify significantly its acidic character. Selectivity results showed that the catalyst produced 2MP, 3MP and the high octane 2,3-dimethylbutane (2,3-DMB) and 2,2-dimethylbutane (2,2-DMB) isomers.     

Probing the catalytic activity of M-N4−xOx embedded graphene for the oxygen reduction reaction by density functional theory

In this work, the detailed oxygen reduction reaction (ORR) catalytic performance of M-N_4−xO_x (M= Fe, Co, and Ni; x = 1–4) has been explored via the detailed density functional theory method. The results suggest that the formation energy of M-N_4−xO_x shows a good linear relationship with the number of doped O atoms. The adsorption manner of O₂ on M-N_4−xO_x changed from end-on (x = 1 and 2) to side-on (x = 3 and 4), and the adsorption strength gradually increased. Based on the results for binding strength of ORR intermediates and the Gibbs free energy of ORR steps on the studied catalysts, we screened out two highly active ORR catalysts, namely Co-N₃O₁ and Ni-N₂O₂, which possess very small overpotentials of 0.27 and 0.32 V, respectively. Such activities are higher than the precious Pt catalyst. Electronic structure analysis reveals one of the reasons for the higher activity of Co-N₃O₁ and Ni-N₂O₂ is that they have small energy gaps and moderate highest occupied molecular orbital energy levels. Furthermore, the results of the density of states reveal that the O doping can improve the electronic structure of the original catalyst to tune the adsorption of the ORR intermediates.     

过渡金属Ni对Pd/Al_2O_3催化剂甲烷催化燃烧性能的影响

考察过渡金属Ni对Pd/Al_2O_3催化剂甲烷催化燃烧活性的影响以及过渡金属负载量及循环条件对甲烷降解性能的影响,采用扫描电镜、N_2吸附-脱附以及H_2程序升温还原技术对催化剂进行表征。结果表明,过渡金属Ni的添加对催化剂在(375~475)℃下的甲烷催化燃烧活性产生影响。催化剂经多次重复使用后,催化燃烧活性提高。分析原因为经过渡金属Ni改性后,可与载体形成NiAl_2O_4尖晶石,促进活性组分形成较小晶粒,并改善活性组分分散度,提高催化剂催化活性。     

The hydrocracking of n-decane over bifunctional Ni-H3PW12O40/SiO2 catalysts

A series of bifunctional Ni-H₃PW₁₂O₄₀/SiO₂ catalysts for the hydrocracking of n-decane were designed and prepared. The evaluation results of the catalysts show that Ni-H₃PW₁₂O₄₀/SiO₂ catalysts possess a high activity for hydrocracking of n-decane and an excellent tolerance to the sulfur and nitrogen compounds in the feedstock. Under the reaction conditions: reaction temperature 300 °C; H₂/n-decane volume ratio of 1500; total pressure of 2 Mpa and the LHSV 2 h⁻¹, the conversion of n-decane over reduced 5%Ni-50%H₃PW₁₂O₄₀/SiO₂ catalysts is as high as 90%, the C₅⁺ selectivity equal to 70%. In order to reveal the structure and nature of the catalysts, a number of characterizations including XRD, Raman, H₂-TPD, NH₃-TPD, XPS and FT-IR of pyridine adsorption were carried out. The characteristic results show that the high activity of the catalysts and high C₅⁺ selectivity can be related to the unique structure of the H₃PW₁₂O₄₀ and its suitable acidity.     

Bound-state Ni species — a superior form in Ni-based catalyst for CH4/CO2 reforming

The effects of nickel loading, calcination temperature, support, and basic additives on Ni-based catalyst structure and reactivity for CH₄ reforming with CO₂ were investigated. The results show that the structure of the nickel active phase strongly depends on the interactions of the metal and the support, which are related to the support properties, the additives and the preparation conditions. “Free” Ni species can be formed when the interaction is weak and their mobility makes them easily deactivated by coking and sintering. The effect of strong metal-support interaction (SMSI effect) is different for various supports. The formation of solid solution of Ni–Mg–O₂ and the blocking of TiO_x by the partially reduced TiO₂ can both decrease the availability of Ni active sites in Ni/MgO and Ni/TiO₂. The spinel NiAl₂O₄ formed in Ni/γ-Al₂O₃ might be responsible for its high activity and resistance to coking and sintering because it can produce a highly dispersed active phase and a large active surface area as bound-state Ni species when the catalyst is prepared at high calcined temperatures or with low nickel loading. The addition of La₂O₃ or MgO as alumina modifiers can also be beneficial for the performance of the Ni/γ-Al₂O₃ catalyst.     

Characterizations and activities of the nano-sized Ni/Al2O3 and Ni/La–Al2O3 catalysts for NH3 decomposition

A series of nano-sized Ni/Al₂O₃ and Ni/La–Al₂O₃ catalysts that possess high activities for NH₃ decomposition have been successfully synthesized by a coprecipitation method. The catalytic performance was investigated under the atmospheric conditions and a significant enhancement in the activity after the introduction of La was observed. Aiming to study the influence of La promoter on the physicochemical properties, we characterized the catalysts by N₂ adsorption/desorption, XRD, H₂-TPR, chemisorption and TEM techniques. Physisorption results suggested a high specific surface area and XRD spectra showed that nickel particles are in a highly dispersed state. A combination of XRD, TEM and chemisorption showed that Ni⁰ particles with the average size lower than 5.0 nm are always obtained even though the Ni loading ranged widely from 4 to 63%. Compared with the Ni/Al₂O₃ catalysts, the Ni/La–Al₂O₃ ones with an appropriate amount of promoter enjoy a more open mesoporous structure and higher dispersion of Ni. Reduction kinetic studies of prepared catalysts were investigated by temperature-programmed reduction (TPR) method and the fact that La additive partially destroyed the metastable Ni–Al mixed oxide phase was detailed.     

铈锆固溶体CexZr1-xO2上H2S的选择性催化氧化性能

采用共沉淀法合成一系列具有不同Ce/Zr物质的量比的铈锆固溶体Ce_xZr_1-xO₂,考察Ce/Zr比例对H₂S选择氧化反应催化活性的影响。通过XRD、BET、Raman、XPS、CO₂-TPD、O₂-TPD、H₂-TPR等手段对铈锆固溶体的晶体结构、表面性质、碱性位以及氧化还原性等进行表征。结果表明,所有的铈锆固溶体催化剂均可以在化学计量比的氧气下具有优良的低温催化活性,催化活性随着Ce/Zr比例的提高而增加,其中Ce_0.9Zr_0.1O₂活性最高,(160~260) ℃转化率均保持在95%以上,在180 ℃时硫收率可达到97%,这主要是因为Ce_0.9Zr_0.1O₂具有最多的中度碱性位、活性位数量和强的氧化还原性。同时推测Ce⁴⁺为催化反应的活性位,并遵循氧化还原机理。此外,催化剂的失活主要是由于催化剂表面生成硫酸盐物种,消耗了活性组分Ce⁴⁺。     

动物骨源羟磷灰石负载Co3O4用于N2O催化分解

通过焙烧猪骨和鸡骨获得羟磷灰石(nHAP)载体,并采用浸渍法制备Co3O4/nHAP催化剂。采用XRD、N2物理吸附-脱附、FT-IR和H2-TPR等对催化剂进行表征,在连续流动微反装置上考察催化剂催化分解N2O的性能。结果表明,相比于鸡骨源Co3O4/nHAP催化剂,以猪骨源HAP为载体的催化剂因其较大的比表面积以及较小的Co3O4粒径尺寸,提供了更多的活性位点。特别是猪骨源Co3O4/nHAP催化剂中适量的K、Na等元素促进了Co^3+到Co^2+的还原,削弱了Co-O键,使催化剂的催化活性显著提高。