基于标准球的显微图像测量系统标定方法

提出一种利用标准球对显微图像测量系统进行标定的方法．该方法利用显微系统小视场小景深的成像特点简化计算模型,减少标定参数．通过标准球图像在水平和垂直方向上的直径比计算比例因子;利用标准球边缘图像的边缘点集．运用优化的方法来计算成像系统的畸变系数和主点位置．系统的放大倍数由标准球的实际直径来标定得出．利用标准球在多摄像机公共视场内其轮廓在任何位置均可见这一特性,可同时对显微图像测量系统中的多个摄像机进行标定,简化标定过程．实验结果表明,该方法标定精度较高,标定后的测量系统的极限误差3σ为2．4μm．     

基于亚像素边缘的摄像机标定板特征提取算法

目的在视觉测量领域,摄像机的标定精度是最终测量精确度的决定性因素,为了提高标定板特征的提取精度,提出一种基于亚像素边缘的提取方法。方法针对圆点标定板,首先采集标定板图像,对图像进行处理,获取像素级别边缘,然后以边缘像素点为中心,取3×3的数字窗口计算梯度方向,在梯度方向上进行像素点灰度的双曲正切拟合,获取亚像素级别边缘,最后对亚像素边缘按照圆形进行拟合,求得圆心坐标。结果实验表明算法的分辨率达到0.03个像素,精度可达0.1个像素。结论该算法具有稳定可靠,精度高,运算速度快等特点,能够应用于图像拼接和分割,特征提取和摄像机标定等领域。     

基于图像边缘特征的零件分类与定位算法

本论文提出了一种基于图像边缘特征的零件分类与定位算法。算法首先对图像腐蚀膨胀等预处理,然后通过边缘检测得零件的完整边缘轮廓,然后对零件边缘轮廓图像使用方向梯度直方图(HOG)构造训练数据,并采用支持向量机(SVM)在训练数据上训练分类识别模型,最后进行检测。根据检测结果获得图像中零件的种类和位置信息,然后使用棋盘格标定的方法来确定深度。标定时,取标定板上的两个点来计算深度,根据已知的深度,获取实际抓取点的两个图像坐标系的x,y值,计算世界坐标系坐标。此系统能解决零件分类、定位问题,能广泛运用于生产线引导工业机器人进行零件抓取。     

一种基于MATLAB的植物叶片参数测量系统

提出了一种基于MATLAB的植物叶片参数自动测量系统方案.该系统利用扫描仪获取包含标定物的叶片图像,对其二值化后进行边缘跟踪,获得标定物和叶片的边界,最后借助标定物的实际直径和面积得到叶片的面积、周长、长、宽等参数.经对两种叶片进行的实验.结果表明,此系统能够快速、准确地进行叶片参数的自动测量,具有较高的效率和实用性.     

仿生复眼系统标定及测量方法研究

为了实现对近景目标物的三维测量,研制了一种小型仿生复眼系统。介绍了该复眼系统的结构及其参数设计原则,并对该系统采用的标定、三维测量等算法进行研究。首先根据复眼成像特点搭建了标定和测量平台,并分别使用张正友的方法、直接线性变换法、Tsai式两步法三种摄像机标定方法对复眼的中心子眼进行标定,通过比较实验结果发现Tsai式标定方法精度更高,更适用于本复眼系统的标定。然后针对边缘子眼光轴与图像传感器不垂直问题,提出了一种新的图像畸变数学模型,有效的提高了边缘子眼的标定精度。最后建立了多子眼三维探测模型,并探索了多子眼成像对复眼相机测量精度的影响,认为三子眼可获得比双子眼更高的精度和稳定性。实验结果表明,在距离复眼相机150?260 mm范围内,该复眼探测系统的三维测量相对误差在2%左右,在满足仪器小型化的同时能基本实现近景三维测量。     

改进的直线拟合线阵CCD图像边缘检测方法

为了检测经过光学系统成像所得图像的边缘,在直线拟合方法的基础上提出了一种新的边缘检测方法。该方法综合考虑边缘过渡区间所有点的信息,利用直线拟合方法求出一组可能的边缘值,再选择它们的中值作为最终的边缘值。基于该方法的采集系统由线阵 CCD 采集边缘的灰度图像,使用单片机来处理数据,并计算出边缘的位置。实验结果表明,这种改进方法的重复性误差为 0.89 个像素,而且能够在 0.039s 内完成一次边缘检测计算。     

立体偏折术的高效标定及法线计算方法

法线计算和系统位姿关系标定是立体偏折术测量的关键技术。针对法线匹配,在立体视觉极线准则的基础上采用假设点的方法,将法线计算转化为一维搜索法线夹角最小值问题。通过查找两个相机对应同一采样点的法线夹角的最小值来获取镜面梯度,最终通过径向基插值函数从梯度数据中恢复镜面精确面形。针对系统位姿关系标定,提出采用将标定板和镜面相结合的位姿关系标定方法。将标定板的厚度纳入标定模型中,提高了标定精度。该方法只需一个镜面反射图像即可确定相机和显示屏幕的位姿关系,使标定过程更加自由和灵活。初步实验验证了所提方法的可行性。     

基于图像处理技术的螺纹几何参数测量

针对螺纹几何参数测量过程中,传统人工测量效率低、仪器昂贵、耗时费力、偶伴有人为误差等不足.本研究采用非接触测量的方法,利用计算机视觉的图像处理技术,通过系统标定、图像采集、图像预处理、边缘检测、几何参数计算等步骤,实现了对螺纹几何参数的自动测量.通过大量实验证明,该系统具有快捷高效、数据可靠、易于操作、替代传统人工操作...     

基于机器视觉的商品条码质量检测方法

目的针对EAN-13商品条码,运用机器视觉技术进行商品条码质量检测,实现一体化、自动化、智能化检验。方法根据检测要求,设计商品条码图像采集装置,通过系统标定完成初始化。条码检测时,采集待测条码图像,进行畸变矫正;通过边缘检测、形态处理和轮廓匹配,找到条码准确位置,分割出条码图像区域,对其旋转校正,分为条码区域和数字区域;对条码区域,水平采样获取反射曲线,计算光学特性参数和译码数据,通过几何特征分析,结合标定参数,计算出相关结构参数;对数字区域,通过字符分割、模版匹配,完成字符识别;最后,通过比对分析,获取全部检测数据。结果分别采用该方法和传统方法,对100个EAN-13条码样本进行了检测对比,试验表明该方法的检验结果符合国家标准,检测数据准确可靠;该方法操作快捷,精度更高,检测速度大幅提高。结论文中方法实现了商品条码质量检测的一体化、自动化、智能化处理,显著提高了检验水平和工作效率。     

立体显微图像的三维微尺度测量方法研究

针对微小复杂产品表面形貌、几何特征、关键点等综合测量的要求,提出了基于立体显微图像的三维微尺度测量方法.利用立体显微镜及两台数字相机获得被测对象两个不同观测角度的显微图像,通过图像处理技术和几何原理计算得到被测对象的空间三维信息,最终实现三维微尺度测量.为了验证所提出方法的有效性,以具有一定倾角的显微标定板为测量对象,在图像采集、滤波、二值化、边缘检测以及形心计算的基础上进行显微系统的标定,分别对左右各10个相同角度进行了实测.结果是相对误差均在3%以内,说明该测量方法可以获得较高的测量精度.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.