The effect of talc on the crystal orientation in polypropylene/ethylene‐propylene rubber/talc polymer blends in injection molding

The effect of tale on the b‐axis orientation of the polypropylene crystals in polypropylene (PP)/ethylene‐propylene rubber (EPR)/talc blends of injection moulding was examined using the X‐ray diffraction method. The b‐axes of the PP crystals were most strongly oriented in the thickness direction for the injection molded PP/EPR/talc blends. The b‐axis orientation in the thickness direction of injection moldings was promoted by increasing the concentration of talc, by reducing the particle size, or by purifying the tale. The dependence of the specimens' rigidity on talc content, particle size, and purity was also investigated. The rigidity depended on the degree of b‐axis orientation. The result of our investigated suggest that increasing the orientation of the PP crystals that are near talc particles may improve the rigidity.     

Intercalated structure of polypropylene/in situ polymerization-modified talc composites via melt compounding

Talc was modified with methyl methacrylate (MMA) or butyl acrylate (BA) via in situ polymerization. The talc/isotactic polypropylene (PP) composites with nano-sized intercalated structure were formed by melt compounding of PP with the modified talc. The results showed that the talc layers were partially delaminated, aligned along the flow direction, and uniformly dispersed in the PP matrix. The thickness of the PMMA-modified talc layers in the PP matrix was in the range 80-240 nm, while the PBA-modified talc was even thinner. PMMA or PBA macromolecules attached on the surface of talc layers hindered the crystallization of the PP component. Moreover, the aligned pristine talc layers promoted the orientation of the PP crystals. However, the extent of PP crystal orientation decreased in the presence of PMMA or PBA-modified talc.     

Influence of talc genesis and particle surface on the crystallization kinetics of polypropylene/talc composites

Talc is a laminar silicate, considered as an excellent nucleating agent for polypropylene (PP) crystallization. However, properties of PP/talc composites depend on the morphology, size, and surface of mineral particles. In this sense, talc from several ores, having different morphology, imparts specific characteristics on these materials. Also, taking into account that PP‐talc adhesion is not necessarily good due to the apolar character of PP, talc surface has been modified in order to increase this parameter. In this work, the effects of talc genesis, geomorphologic aspects, and particle surface characteristics on crystallization of PP/talc composites are analyzed. Isothermal crystallization of PP/talc composites was studied by using differential scanning calorimetry, based on Avrami model. The final crystalline morphology of talc‐filled PP was analyzed by means optical microscopy. The results show that the blocky talc morphology favors even more the crystallization compared to the platy one, at the same particle size. Taking into account the surface treatment studied in this work, the talc surface is made hydrophobic and the particle delamination is favored. As a consequence, so‐modified talc is very effective in increasing the crystallization temperature of PP and the nuclei number that grow during the crystallization with respect to the untreated talc. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical properties,morphology, and crystallization behavior of polypropylene/elastomer/talc composites

In this study, polypropylene/ethylene–octene copolymer (PP/POE) blends, PP/talc, and PP/POE/micro‐talc (MT) composites were fabricated using a twin screw. To estimate the performances of the PP/POE blends, PP/talc, and PP/POE/MT composites, mechanical properties, heat deflection temperature (HDT), thermomechanical analysis, and isothermal crystallization characterization were conducted. Incorporating talc particles increased the tensile strength, flexural properties, and HDT of the PP matrix, but reduced the elongation at break and notched impact strength. The inclusion of POE elastomers in the PP matrix yielded the opposite effect on PP/talc composites. PP/POE/MT composites provide a compromise that improves both the flexural properties and notched impact strength. Moreover, the inclusion of talc particles in PP/POE blends induced heterogeneous nucleation and considerably reduced the crystallization time. Consequently, the time required for processing was also greatly reduced. POLYM. COMPOS., 36:69–77, 2015. © 2014 Society of Plastics Engineers     

Unique clay orientation in the injection-molded bar of isotactic polypropylene/clay nanocomposite

In this article, the injection-molded bars of isotactic polypropylene/organoclay nanocomposite with different clay contents have been obtained via dynamic packing injection molding (DPIM). The oriented microstructure including layered nanoparticles and PP lamellae has been inspected through 2D-WAXS analyses along the sample thickness of the molded bars. Depending on the clay content and sample thickness, various oriented clay structures with nanoparticles uniplanar-axially oriented parallel to the surface of molded bar, or partially tumbled around the flow axis of the molded bar, or even a random orientation, could be observed. The observed orientation behavior of nanoparticles could be temporarily elucidated as the results of the sensitive response of layered nanoparticles to shear deformation and the structural recovery of clay network assisted by the electrostatic attraction existing between adjacent nanoplatelets.     

Effect of silane‐grafted polypropylene on the mechanical properties and crystallization behavior of talc/polypropylene composites

Talc‐filled polypropylene (PP) composites coupled with silane‐grafted polypropylene (PP‐g‐Si) were prepared. Effect of PP‐g‐Si on the mechanical properties, crystallization, and melting behavior of PP composites was investigated. Compared with the uncoupled composites, the mechanical properties of Talc/PP composites coupled with a small amount of PP‐g‐Si were increased to some extent. Meanwhile, PP‐g‐Si can promote crystallization rate and increase crystallization temperature of PP in the composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2974–2977, 2000     

The effect of talc on the crystallization of isotactic polypropylene

Isotactic polypropylene (iPP) has been crystallized in the presence of talc under the quiescent state and shear flow of injection molding. The resulting morphology has been investigated by means of polarizing microscopy, transmission electron microscopy, and wide angle X‐ray diffraction. In the quiescent state, the iPP lamellae grew from the surface of talc and the transcrystalline region was formed at the interface between iPP melt and the talc. The nucleation of iPP was very frequent on the cleavage plane of talc. The X‐ray diffraction pattern of the transcrystal showed a*‐axis orientation to the crystal growing direction. In injection‐molded samples of the talc‐filled iPP, the morphology of lamella growing from talc appeared as same as that of the transcrystal. However, the crystalline orientation of injection‐molded talc‐filled iPP, in which the b axis was oriented to the thickness direction and the a* and the c axis was oriented to the flow direction, was quite different from that of the transcrystal. This b‐axis orientation results from the orientation of the plate plane of talc, which induces the nucleation and the crystallization under shear flow. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1693–1703, 2001     

Crystallization behavior of polypropylene filled with surface-modified talc

Talc-filled polypropylene (PP) composites were prepared by extrusion in a wide composition range (0–40 wt %). To improve the affinity relation between talc and the PP matrix, we modified the talc surface with silane coupling agents. Differential scanning calorimetry investigations on test samples, prepared by injection moulding, revealed that the talc content and its surface modification had a pronounced effect on the crystallization behavior of the filled PP composites. The experimental results indicate that a talc concentration of 2 wt % strongly affects the nonisothermal crystallization process of the PP, especially when talc is silane treated Isothermal crystallization experiments on samples with minimum amounts of talc (2 wt %) revealed an improved nucleation activity with silane-treated talc. © 1996 John Wiley & Sons, Inc.     

Orientation in composite of polypropylene and talc

X-ray diffraction and microscopical investigation of test samples prepared by injection molding from composites of isotactic polypropylene with talc revealed a preferred orientation of the talc and polypropylene matrix. Contrary to the situation in polypropylene alone, the preferred orientation in polypropylene–talc composites survived melting and a new crystallization. Crystallization rate measurements confirmed the nucleation activity of talc for polypropylene crystallization.     

Crystallization and morphology of reactor-made blends of isotactic polypropylene and ethylene-propylene rubber

The crystallization and morphology of reactor-made blends of isotactic polypropylene (PP) with a large content of ethylene-propylene rubber (EPR) (i.e., > 50%) were investigated. In the blends, PP was found to form spherulites during the crystallization process, with the growth rate constant under isothermal conditions. For crystallization temperatures in the range of 118–152°C, the birefringence of the spherulites varied from negative to positive by decreasing crystallization temperature, while homopolypropylene (homo-PP), the same as used in the blends as a matrix, showed negative spherulites in the whole temperature range investigated (118–152°C). Both the spherulite growth rate and the overall crystallization rate were slower for the blends than for homo-PP. The density of the crystallization nuclei was lower in the blends than in the homo-PP. It was concluded that a large amount of EPR content in the reactor-made blends of PP retards and hinders the crystallization of the matrix. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1007–1014, 1997     

Tensile elongation of high‐fluid polypropylene/ethylene–propylene rubber blends: Dependence on molecular weight of the components and propylene content of the rubber

We studied tensile behavior of low‐molecular‐weight (MW) polypropylene (PP)/ethylene–propylene rubber (EPR; 70/30) blends from the viewpoint of the MWs of PP and EPR and the compatibility between PP and EPR. The value of the melt flow rate of PP varied from 30 to 700 g/10 min at 230°C. We studied the compatibility between PP and EPR by varying the propylene content in EPR (27 and 68 wt %). At the initial elongation stage, crazes were observed in all blends. When blends included EPR with 27 wt % propylene, the elongation at break of the low‐MW PP improved little. The blends with EPR and 68 wt % propylene content were elongated further beyond their yielding points. The elongation to rupture was increased with increasing MW of EPR. Molecular orientation of the low‐MW PP was manifested by IR dichroism measurements and X‐ray diffraction patterns. The blends of low‐MW PP and EPR could be elongated by the partial dissolution of EPR of high‐MW in the PP amorphous phase. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 46–56, 2002     

Non-isothermal crystallization kinetic and compatibility of PTT/PP blends by using maleic anhydride grafted polypropylene as compatibilizer

The crystallization behaviors, non-isothermal crystallization kinetics, and the morphology of poly(trimethylene terephthalate)/Polypropylene (PTT/PP) blends using a maleic anhydride grafted polypropylene (PP-g-MAH) as a compatibilizer were investigated by differential scanning calorimeter (DSC) and scanning electron microscope (SEM), respectively. The results suggested that the blends exhibited different crystallization and melting behaviors due to different content of PP-g-MAH. All of the DSC curves of the blends exhibited two exothermic peaks and endothermic peaks. The commonly used Avrami equation modified by Jeziorny, Ozawa theory and the method developed by Mo were used, respectively, to fit the primary stage of non-isothermal crystallization process. The results suggested that the crystallization rate of PTT component was increased, whereas, that of PP component was retarded with the introduction of PP-g-MAH. The effective activation energy was calculated by differential iso-conversional method developed by Vyazovkin. The SEM result suggested that the introduction of PP-g-MAH greatly improved the compatibility between PTT and PP, and decreased the size of dispersed particles.     

Effect of talc on the properties of polypropylene/ethylene/propylene/diene terpolymer blends

In the present study, the effect of talc content on the mechanical, thermal, and microstructural properties of the isotactic polypropylene (i‐PP) and elastomeric ethylene/propylene/diene terpolymer (EPDM) blends were investigated. In the experimental study, five different talc concentrations, 3, 6, 9, 12, and 15 wt %, were added to i‐PP/EPDM (88/12) blends to produce ternary composites. The mechanical properties such as yield and tensile strengths, elongation at break, elasticity modulus, izod impact strength for notch tip radius of 1 mm, and hardness with and without heat treatments and thermal properties, such as melt flow index (MFI), of the ternary composites have been investigated. The annealing heat treatment was carried out at 100°C for holding time of 75 h. From the tensile test results, an increased trend for the yield and tensile strengths and elasticity modulus was seen for lower talc contents, while elongation at break showed a sharp decrease with the addition of talc. In the case of MFI, talc addition decreased the MFI of i‐PP/EPDM blends. It was concluded that, taking into consideration, mechanical properties and annealing heat treatment, heat treatment has much more effect on higher yield and tensile strengths, elongation at break, elasticity modulus, impact strength, and hardness. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3033–3039, 2006     

聚丙烯/超高相对分子质量聚乙烯共混物的结晶动力学及发泡性能研究

采用差示扫描量热仪（DSC）对含有不同含量超高分子量聚乙烯（UHMWPE）的聚丙烯进行测试和表征,采用Ozawa方法、莫志深方法和Kissinger方法分析了该体系的非等温结晶动力学。利用自行研制的超临界流体挤出发泡实验装置,对含有UHMWPE的PP进行了超临界二氧化碳挤出发泡实验研究。结果表明：超高分子量聚乙烯的加入降低了PP的结晶活化能,含有UHMWPE的PP在较高的温度下开始结晶,且由于超高分子量聚乙烯大分子链的存在,与聚丙烯分子链发生缠结,阻碍聚丙烯分子链排入晶格,降低了结晶速率,结晶温区拓宽,有利于聚丙烯挤出发泡成型;加入UHMWPE后,PP的发泡效果明显改善,泡孔平均直径减小,泡孔尺寸分布更加均匀,PE-UHMW的含量为5份时,表观密度达到0.038g/cm-3。     

Crystallization Behaviors of amino-terminated polyurethane (ATPU)-grafted polypropylene

Summary A melt-grafting approach was employed to prepare a novel functional polypropylene(FPP)—amino-terminated polyurethane grafted polypropylene (PP-g-ATPU). The crystallization behaviors of PP and PP/FPP blends were characterized using differential scanning calorimetry (DSC), wide angle X-ray scattering (WAXS) and polarized optical microscopy (POM). The effects of FPP composition on crystallization behavior, crystal transformation, and morphology of PP/FPP crystalline were investigated. The results showed that at a low dosage (<2.0 wt%) ATPU acted as a heterogeneous nucleation agent during the crystallization of PP/FPP blends. However, when the content of ATPU reached 2.0 wt% or higher, ATPU deteriorated the crystallization of PP or PP/FPP blends. The crystallite size decreased and the number of crystallites increased as the ATPU content increased. The Avrami analysis was adopted to describe the isothermal crystallization process. The difference in the exponent n between PP and PP/FPP suggested that the isothermal crystallization kinetics of PP/FPP blends followed a three-dimensional growth via heterogeneous nucleation. In terms of the half-time of the crystallization, t_1/2, the crystallization rate of functional PP blends was faster than that of PP homopolymer at a given crystallization temperature.     

Effects of compatibilization of oxidized polypropylene on PP blends of PP/PA6 and PP/talc

The influence of compatibilization on the dynamic mechanical properties of polypropylene (PP) binary blends with polyamide‐6 (PA6), Talc, and oxidized PP (OPP) was investigated. The oxidation of PP homopolymer was performed in a internal mixer by using air as a oxidizing agent (under atmospheric pressure) and dodecanol‐1 as an accelerator at 180°C for 6½ h [Abdouss, M.; Sharifi‐Sanjani, N.; Bataille, P. J Appl Polym Sci 1999, 36, 10]. In the blends, OPP was used as a blend component and compared with PP over the whole concentration range. Pressed film blends of PP/OPP, PP/OPP/Talc, and PP/OPP/PA6 were examined by dynamic mechanical analyzer, thermal gravimetry analysis, and scanning electron microscopy. Mechanical properties such as tensile strength, modulus of elasticity, elongation, melt flow index, and hardness of the blends were measured. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2871–2883, 2004     

Shear-induced epitaxial crystallization in injection-molded bars of high-density polyethylene/isotactic polypropylene blends

As a continuation of our previous works on exploring shear-induced epitaxial crystallization of polyolefin blends during practical molding processing [Na et al. Polymer 2005; 46, 819 and 5258], the present study focused on the importance of molecular weight on the formation of epitaxial structure in injection-molded bars of high-density polyethylene (HDPE)/isotactic polypropylene (iPP) blends. By choosing two kinds of HDPE and two kinds of iPP with high molecular weight or low molecular weight, four blends with different molecular weight combinations can be designed. After making the blends via melt mixing, the injection-molded bars were prepared in a so-called dynamic packing injection molding equipment where repeated shearing was imposed on the melts during the solidification stage. Crystal structure and orientation were estimated mainly through 2D-WAXD. Our results indicated that an appropriate matching of low molecular weight HDPE and high molecular weight iPP was more favorable for epitaxial crystallization than other component matches. The effects of orientation and epitaxy on the re-crystallization behaviors of polyolefin blends have been elucidated in detail through PLM experiments. Moreover, epitaxy has been proved to play a positive effect in determining the ultimate mechanical properties of injection-molded bars.     

高温熔融对PP/EPR/PE-UHMW分子链扩散作用以及流变和结晶性能的影响

采用一种简便易行的方法使高度缠结的超高相对分子质量聚乙烯（PE-UHMW）与乙丙橡胶（EPR）的分子链得到有效的扩散,并最终将EPR/PE-UHMW预混物与聚丙烯（PP）共混形成PP/EPR/PE-UHMW三元共混物。并研究了该三元共混物的流变性能和结晶性能。结果表明,在预混物体系中,经历高温熔融处理后,流变曲线出现不同于一般EPR材料的难松弛结构的低频平台区,说明PE-UHMW与EPR分子链相互扩散形成长分子链缠结结构;其缠结结构在PP/EPR/PE-UHMW共混物中减慢了PP基体流变曲线低频平台区出现的趋势,限制了EPR向PP基体的扩散; EPR与PE-UHMW分子链之间的相互扩散,对高度缠结的PE-UHMW具有增塑作用,导致PE-UHMW结晶温度下降和结晶度上升;二元预混物添加进入PP基体中,促使PP多重熔融现象的发生。     

Crystal orientation distributions in injection-molded polypropylene compounds

The crystal orientation distribution in injection-molded bars made from several polypropylene compounds has been investigated using pole figure analysis. The fillers used were glass fibers, chalk, and talc, and some compounds contained one filler and others contained glass fibers plus one or both of the others. All compounds showed strong orientation in the skin with the b-axis of the monoclinic crystals lying preferentially normal to the flow direction and in many cases parallel to the normal to the bar face. This normal direction orientation was very strong in compounds containing talc and is probably caused by crystals forming with their (010) planes on the talc platelet faces, which align themselves parallel to the mold face. Strong orientation persists into the interior of the moldings containing talc, whereas in the other compounds, the orientation at intermediate depths is much less pronounced than in the skin. © 1992 John Wiley & Sons, Inc.     

Crystallization behaviors of polypropylene and functional polypropylene

The crystallization behaviors of polypropylene (PP) homopolymer and its blends with 0–15% functional polypropylene (FPP), the backbones of which were grafted with guanidine and diamide polymer chains, were investigated with differential scanning calorimetry and wide‐angle X‐ray scattering. The crystallization kinetics were studied with spectral depolarization. The results revealed that the presence of FPP reduced the crystallinity and crystallite size of PP. Meanwhile, FPP increased the crystallization rate. Compared with that of the PP homopolymer, the crystallization temperature of PP/FPP blends was increased by more than 10°C. During isothermal crystallization, the relative crystallinity, developed as a function of time, was described by the Avrami equation. The half‐time of crystallization for PP/FPP blends was much shorter than that for the PP homopolymer. The half‐time of crystallization of PP/FPP blends depended much less on the crystallization temperature than that of the PP homopolymer. Therefore, FPP accelerated the crystallization rate of PP in a manner similar to that of a nucleator. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 872–877, 2003