粉末冶金陶瓷模工艺中的快速脱蜡新技术

粉末冶金陶瓷模工艺是一种先进的过净形成形工艺．本文报道该工艺中一种新的脱蜡技术．采用快速加热、管径集中热量和定向导热传热综合方法，在陶瓷模和大部分蜡模材料处于较低温度下，使蜡模材料来不及发生显著的热膨胀而直接蒸发，得到脱蜡干净、外形完整的陶瓷模．     

A New Shaping Model for Green Ceramic Balls

The shaping quality of green ceramic balls is directly related to the efficiency and cost of later machining for the ceramic balls. Until now the shaping for green ceramic balls is still conducted by handwork. In this paper, a new shaping model for green ceramic balls was designed. In the new model, two grinding wheels with the same generator line as circular arc are mounted on symmetry, and their axes are parallel. The green ball can be put in the enveloping space formed by the two grinding wheels. The rad...     

Abnormal dielectric characteristics of PMN-32%PT single crystal under dc bias

It has been reported that the single crystal of relaxor ferroelectrics (1-x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 (PMN-xPT) with the compositions near the morphotropic phase boundary (MPB, 0.28相似文献   

Study on Ceramic Cutting by Plasma Arc

Engineering ceramics are typical difficult-to-machine materials because of high hardness and brittleness. PAC (Plasma Arc Cutting) is a very important thermal cutting process and has been successfully used in cutting stainless steel and other difficult-to-machine alloys. PAC‘s application in cutting ceramics, however, is still limited because the most ceramics are not good electronic conducts, and transferred plasma arc cannot be produced between cathode and work-piece. So we presented a method of plasma ...     

SAG法合成钛酸铅纳米晶粒的工艺和结构研究

ＳＡＧ法合成钛酸铅纳米晶粒的工艺和结构研究李永祥刘泽吴冲若（东南大学电子工程系,南京２１００９６）ＰｂＴｉＯ３是应用广泛的铁电和光电材料之－,研究ＰｂＴｉＯ３纳米晶粒的合成技术和电学性能对基础研究和新型复合功能材料研究都有重要意义．作者曾采用Ｓｏｌ...     

新型压电陶瓷涡街流量计

介绍一种新型的压电陶瓷涡街流量计,该流量计采用ＢＳＴ压电陶瓷元件来检测旋涡释放频率,使该流量计能在高温工况下工作,一年多的工业现场运行试验结果表明,新研制的涡街流量计可靠性高、稳定性好,在４００℃高温和１０ＭＰａ高压下能长期连续正常运行。     

前驱体溶液pH值对溶胶凝胶制备钛酸铋薄膜的影响

采用溶胶凝胶技术在石英玻璃基片上制备钛酸铋薄膜,讨论了前驱体溶液的酸碱度（ｐＨ值）对薄膜结构和结晶性的影响．ｐＨ＜２和ｐＨ＞３５的前驱体溶液所制备的薄膜在晶化过程中出现Ｂｉ２Ｔｉ２Ｏ７和Ｂｉ２Ｔｉ４Ｏ１１杂相．ｐＨ＝２５～３５的前驱体溶液制备的薄膜是钙钛矿Ｂｉ４Ｔｉ３Ｏ１２结构的取向薄膜     

ZrO2陶瓷材料在水环境中的疲劳断裂特性

采用断裂力学中的四点弯曲试验法 ,对 Zr O_2 陶瓷材料分别在大气、水环境中的静疲劳和循环疲劳破坏特性进行研究 ,通过扫描电子显微镜 (SEM)对试验片断裂面的微细组织进行观察 ,分析并阐明了造成材料疲劳断裂的机理 .结果表明 ,相同应力条件下 ,材料在水环境中的疲劳寿命比大气环境中低以及循环疲劳对材料的疲劳寿命起到劣化作用 ,该劣化作用可以认为是由于循环应力使得微裂纹增加和扩展造成的 .     

以LaNiO3作为底电极的Pb(Zr0.3,Ti0.7)O3铁电薄膜的性能研究

采用溶胶－凝胶法在Si(100）衬底上制备了LaNiO3薄膜，采用相同方法在LaNiO3/Si(100）上制备了Pb（Zr0.3,Ti0.7）薄膜，对LaNiO3薄膜和Pb(Zr0.3,Ti0.7）O3薄膜的结晶性，表面形貌和电性能进行了研究。