THE PRACTICE OF ACRYLIC SIROSPUN YARN ON THE SEMI WORSTED SPINNING FRAME

The technique of sirospun process is applied on a modified semi-worsted balloonless spinningframe to investigate the effect of spindle-speed,yarn-twist and strand-spacing on yarn properties.Yarn breaking strength,breaking extension,evenness and imperfection are examined on the basisof CCD experimental design.Yarn hairiness is particularly concerned,being found that all spinningparameters tested have significant effects on hairiness and that the minimum number of hairs oc-curs at the strand-spacing of 14.4 mm.Compared to conventional single spun yarn,experimentshave revealed the greatest advantage of using sirospun process is that all sirospun yarns have muchless hairiness.A new sirospun yarn fault,so called“loop”,has also been examined.The most likely cause forthis yarn fault is the strand-tension unbalance between the two strands when low tension spinningis applied.Further analysis and some initial tests have been carried out in the hope of overcomingthis loop fault which is an important obstacle to the application of balloonless spinning.     

THE INFLUENCE OF SPINNING CONDITION ON STRUCTURE & PROPERTIES OF MASS-DYED SUPERFINE PP AS-SPUN FILAMENTS

The effect of colorant additive on the rheology of PP polymer melt and the influence of spinning conditions on the crystalline and orientation structure of mass-dyed as-spun PP filament are reported. The △E~~~ value for all colored chips is higher than that of blank chip to a varying degree. The crystallinity and orientation degree of dyed PP as-spun filament decrease with increasing melt temperature, decreasing spinning speed and increasing denier per filament (dpf), while the crystallinity of dyed as-spun filament increases with the content of colorant additive as a nucleation agent.     

NiAl金属间化合物熔体旋转法制备工艺参数研究

研究了金属间化合物快速凝固薄带的成型过程和影响薄带质量的工艺参数。提出了熔体在喷嘴处进行层流流动的经验关系式，给出了金属间化合物快速凝固薄带制备的最佳工艺参数。     

二十一世纪纺纱工程展望

二十一世纪,一些相关高新技术的发展和应用,将对传统工程产生巨大的影响和推动。文章在此基础上,对新世纪前半叶纺纱技术、纺纱设备以及纺纱工厂自动化的发展进行了展望。     

喷丝头组合花板的真空熔炼

化纤生产行业的粘胶，经过装在组合花板上的喷丝头在酸浴里形成化学纤维。粘胶为碱性物质，酸浴的化学成份为稀硫酸、磷酸，酸浴温度为57℃左右，组合花板内压力为10kg／cm^2，要求组合花板材料在有足够的强度下，具有高耐腐蚀性能。     

集聚纺集聚区须条等截面部分的力学分析

通过对集聚区内须条的集聚过程分析，建立须条的受力模型，发现须条在集聚过程中会产生附加捻度，并且对影响须条附加捻度的各种因素：异型管开槽长度、负压大小、须条和网格套圈间的摩擦因数以及异型管的曲率半径进行了分析。设计相关实验对集聚区内须条的力学模型进行了验证。结果表明所建立的集聚区内须条的力学模型是正确的。     

二醋酯纤维的结构特性

采用DSC、X-射线衍射和密度梯度管等技术研究了二醋酯纤维的结晶、取向等结构特性，初步探讨了不同纺丝工艺对纤维结构特性的影响，发现：二醋酯纤维存在两种晶型结构，结晶度和取向度都较低；以相同二醋片为原料时，纺丝工艺对纤维的结构特性有影响但不明显，而烟用纺丝工艺和纺织用纺丝工艺之间的差别对纤维结构特性的影响则相对较大。     

成丝的速度与方式和蜘蛛丝力学性能的关系

为了分析蜘蛛丝的力学性能和成丝条件间的关系,研究了不同速度下人工卷取的蜘蛛牵引丝以及蜘蛛垂直下落时分泌的牵引丝的力学性能.研究结果表明,随着卷取速度的增大,蜘蛛丝的断裂强度有一极大值,在高速卷取时强度的变化较低速时平缓.垂直下落时蜘蛛分泌的牵引丝的综合力学性能优异,但断裂强度不一定大于人工卷取的丝.成丝速度和成丝方式都对蜘蛛丝的性能有很大影响.     

长圆柱形接地体接地电阻的计算

用一种较简捷的方法导出了长旋转椭球导体的电位,从而近似计算了长圆柱形接地体的接地电阻.     

纳米双相钕铁硼永磁合金的织构及磁畴

为开发纳米复合永磁材料高磁能积的潜力,用熔体快淬法制备各向异性的纳米双相快淬带。X光衍射结果表明,Nd9Fe85-xNbxB6(x=0,0.5,1.0)快淬带中存在垂直于带面的Nd2Fe14B[00L]织构,其自由面上的织构强于贴辊面。x=1.0时,在15m.s-1的快淬速度下的择优取向度为94%。磁力显微镜观察表明晶粒间存在强烈的交换耦合作用。x=0.5时的快淬带具有较强交换耦合作用及高织构度,因此具有最佳磁性能。其剩余磁极化强度为1.130T,内禀矫顽力为519.8kA.m-1,最大磁能积为121.2kJ.m-3。