论建立动态勘探目标评价体系的迫切必要性

从国际上通行的油气勘探评价工作重点,中国石油所面临的"已逐步进入一个不断在老区范围内开展精细勘探、在老区范围内开展新区块、新层系勘探以获得主要的储量增长"的新的勘探形势,现有地质研究中各专题研究与具体勘探目标评价脱节等多个方面,论述了在中国石油内部建立一套动态勘探目标评价体系的迫切必要性;并在此基础上阐述了一个完整的动态勘探目标评价体系应包括的主要内容;最后对该体系的建设进行了可行性分析。     

300km/h高速铁路PC槽型梁动力试验研究

介绍北方交通大学与比利时鲁汶大学、布鲁塞尔自由大学、比利时铁路公司合作,在巴黎至布鲁塞尔之间高速铁路线上的Antoing大桥进行的二次高速铁路桥梁动力试验。试验桥梁由跨度50m的多跨预应力混凝土简支槽型梁构成,试验中列车速度达265-310km/h。通过现场试验和实验结果分析,得到了桥梁的频率、振型、阻尼等自振特性,以及桥梁在高速列车作用下的动挠度、梁和桥墩的横向和竖向加速度、橡胶支座的相对位移、梁体的动应变等动力响应特性。试验经验和测试结果对于充实高速铁路桥梁动力分析理论、改进数值分析模型、验证计算结果、提高高速铁路桥梁的动力设计水平、保证行车安全,具有重要的意义。     

具有阻力特性材料的σ_f－σ关系及一种新的阻力曲线测定方法

通过对相变增韧陶瓷及一种可切削玻璃－陶瓷动态疲劳（恒应力速率）试验中高应力速率区断裂应力下降现象的理论分析，发现这种现象与材料的阻力特性（Ｒ－ｃｕｒｖｅ）密切相关。确立的σ_ｆ－σ理论关系能够很好地描述整个应力速率区间内的动态疲劳试验结果。高应力速率区σ_ｆ－σ在双对数坐标下为负斜率直线，直线斜率为（ｍ为阻力曲线ＫＲ＝ｋ（△ａ）~ｍ的指数），断裂主要由材料阻力行为控制；低应力速率区，σ_ｆ－σ在双对数坐标下为正斜率直线，直线斜率为　（ｎ为应力腐蚀指数），断裂主要由材料应力腐蚀行为控制。建立了测定材料阻力特性的一种新方法，分别用这种方法及压痕／弯曲方法对一种可切削玻璃－陶瓷的阻力特性进行了实验测定，两种方法所得结果有很好的一致性。     

荧光显示管直丝氧化物阴极有效逸出功的计算

阴极的逸出功是表征阴极发射能力的物理量，求定荧光显示管直丝氧化物阴极有效逸出功时，因其零场发射电流密度难于准确取值，温度无法直接测量，显得困难，须予解决，为此提出了一种计算阴极有产逸出功的办法，对某显示管的发射欠佳和“低温高效”的两种氧化物阴极的有效逸出功进行计算，有效逸出功率是靠测量相关物理量再同计算得出，精度不很高，文中所用办法也不例外，但所得结果能反映阴极发射能力，所需仪器少，是实用方法。     

Control strategies for reactive batch distillation

A batch reactor may be combined directly with a distillation column by distilling off the light component product in order to increase the reactor temperature or to improve the product yield of an equilibrium reaction. The same amount of the light product should be removed as the amount being formed by the reaction at any time. A linearized model has been developed which describes the process behaviour satisfactorily for control analysis purposes. The controllability of a combined batch reactor/batch distillation column is found to depend strongly on the operating conditions and on the time during the run. In general, controlling only the reactor temperature (one-point bottom control) is difficult since the set-point has to be specified below a maximum value in order to avoid break-through of an intermediate component in the ditillate. This maximum value may be difficult to know a priori. For the example considered in this study, control of both reactor temperature and distillate composition (two-point control) is also found to be difficult due to large interactions in the column. As with one-point bottom control, the reactor temperature has to be specified below a maximum value. However, energy can be saved since the heat duty can be decreased with time. Controlling the temperature on a tray in the column (one-point column control) is found to give good performance for the given process with no loss of reactant and a high reactor temperature, although no direct control of the reactor temperature is obtained.     

头盔显示器的关键技术及有关设计问题综述

头盔显示器可以提高驾驶员的态势感知能力，红外传感器提供的信息，使驾驶员的态势感知能力大大加强，头盔显示器提供的红外图像，使恶劣的天气和黑夜不再成为驾驶员作战的障碍，概述了头盔显示器的发展过程和关键技术，介绍了当前空军用头盔显示器的技术问题，解决方法，设计示例。     

Voltage sag compensation with minimum energy injection by use of a micro‐SMES

This paper presents a method to compensate voltage sags with minimum energy injection for a series‐connected voltage restorer using a micro‐SMES. A circuit for extracting the fundamental symmetrical components from sag voltages and a minimum energy injection algorithm is described. Simulations of voltage sag compensation have been carried out using PSCAD/EMTDC for various faults. The simulation results confirm the validity of the proposed method and show the possibility of reducing the size of energy storage devices. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(3): 70–80, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10047     

NBR/PP热塑性弹性体研究进展

阐述了NBR／PP共混热塑性弹性体动态硫化胶的国内外研究进展、微观相态结构、性能、应用及展望。     

Critical Configurations for 1-View in Projections from ℙ<Superscript>k</Superscript> → ℙ<Superscript>2</Superscript>

In this paper we describe, from a theoretical point of view, critical configurations for the projective reconstruction of a set of points, for a single view, i.e. for calibration of a camera, in the case of projections from ℙ^k to ℙ² for k ≥ 4. We give first a general result describing these critical loci in ℙ^k, which, if irreducible, are algebraic varieties of dimension k−2 and degree 3. If k=4 they can be either a smooth ruled surface or a cone and if k = 5 they can be a smooth three dimensional variety, ruled in planes, or a cone. If k≥ 6, the variety is always a cone, the vertex of which has dimension at least k − 6. The reducible cases are studied in Appendix A. These results are then applied to determine explicitly the critical loci for the projections from ℙ^k which arise from the dynamic scenes in ℙ³ considered in [13]. Marina Bertolini is currently Associate Professor of Geometry at the Department of Mathematics at the Università degli Studi di Milano, Italy. Her main field of research is Complex Projective Algebraic Geometry, with particular interest for the classification of projective varieties and for the geometry of Grassmann varieties. On these topics M. Bertolini has published more than twenty reviewed papers on national and international journals. She has been for some years now interested also in applications of Algebraic Geometry to Computer Vision problems. Cristina Turrini is Associate Professor of Geometry at the Department of Mathematics of Università degli Studi di Milano, Italy. Her main research interest is Complex Projective Algebraic Geometry: subvarieties of Grassmannians, special varieties, automorphisms, classification. In the last two years she has started to work on applications of Algebraic Geometry to problems of Computer Vision. She is author or co-author of about thirty reviewed papers. She is also involved in popularization of Mathematics, and on this subject she is co-editor of some books.     

Rheological and drug‐release behaviour of a scleroglucan gel matrix at different drug loadings

The aim of this study was to investigate the drug‐loading effects on release and mechanical properties of a scleroglucan gel, with the intention of considering them in delivery systems formulations. The rheological and kinetic properties of a 2 % w/w scleroglucan gel matrix loaded with 0, 0.02, 0.04, 0.06, 0.2 and 0.4 % w/w of theophylline (Th, used as a model drug) were investigated. Rheological measurements were performed in a controlled‐stress rotational‐shear rheometer under isothermal conditions. For theophylline release from the gel a flat Franz cell was used and the kinetic parameters were derived applying a semi‐empirical power law. The influence of scleroglucan molar weight on kinetic and rheological behaviour was also studied. Results suggest two possible effects of drug loading on the gel network: in the 0.04–0.06 % w/w Th range a plasticizing effect and in the 0.2–0.4 % w/w Th range a rigidization effect. In the first range mentioned, the changes in the gel structural properties tested by means of rheological measurements are coincident with changes in drug‐release kinetics. Copyright © 2005 Society of Chemical Industry