Influence of iron oxide pigments on the properties of concrete interlocking blocks

Concrete interlocking blocks (CIBs) are utilized in a variety of commercial, municipal, and industrial applications. Superior engineering properties, low maintenance, ease of placement and removal, reuse of original blocks, aesthetic appeal, and immediate availability are the primary reasons for choosing concrete block pavement over other paving surfaces. It is a common practice to pigment building materials, such as mortar, concrete pavers, concrete roof tiles, and prefabricated concrete products; CIBs are colored using iron oxide pigments. This article presents experimental results detailing the properties of CIBs dyed with pigments. The results of these experiments are as follows: Because the particles of iron oxide pigments are finer than those of brown iron oxide, interlocking blocks mixed with the former acquired higher color strength than with the latter. Additional analysis determined a definite relationship between the flexural strength and the absorption ratio of pigment-dyed blocks; the correlation coefficient (R²) of interlocking blocks at 91 days was .90. It is suggested that if iron oxide pigments are to be used to color CIBs, the pigment-to-cement ratio should be below 4%.     

Physico-chemical properties of ceramic pigments for high-temperature application

Heat resistant coatings are required primarily for stacks, exhaust pipes, reactors, space crafts and similar equipments that are permanently or occasionally exposed to elevated temperatures. High-temperature coatings are generally based on silicone resin with ceramic and metallic pigments. In this study, iron oxide, cobalt oxide (thermo chromic compound) and aluminum oxide are used for the preparation of four new types of coloured pigments. The thermal resistant characteristics of these ceramic pigments were studied by differential thermal analysis, thermo gravimetric analysis and differential scanning calorimetric analysis. These ceramic pigments are found to be thermally stable up to 400 °C.     

A simple mathematical analysis on the effect of sand in Cr(VI) reduction using zero valent iron

A simple mathematical model was proposed to analyze the enhancement of Cr(VI) reduction when sand materials are added to the zero valent iron (ZVI). Natural decay of Cr(VI) in a control experiment was analyzed by using a zero-order decay reaction. Adsorption kinetics of Cr(VI) to sand was modeled as a first-order reversible process, and the reduction rate by ZVI was treated as a first-order reaction. Natural decay of Cr(VI) was also included in other experiments, i.e., the adsorption to sand, the reduction by ZVI, and both adsorption and reduction when sand and ZVI are present together. The model parameters were estimated by fitting the solution of each model to the corresponding experimental data. To observe the effect of sand addition to ZVI, both adsorption and reduction rate models were considered simultaneously including the natural decay. The solution of the combined model was fitted to the experimental data to determine the first-order adsorption and reduction rate constants when sand as well as ZVI is present. The first-order reduction rate constant in the presence of sand was about 35 times higher than that with ZVI only.     

Preparation of one-dimensional polymer films by modification of a hydroxymethylbenzene self-assembled monolayer on iron with alkyltriethoxysilanes for preventing iron corrosion

A self-assembled monolayer (SAM) of p-hydroxymethylbenzene HOCH₂C₆H₄ - (HOMB) moiety adsorbed on iron by the formation of a covalent bond between carbon and iron atoms was prepared by electrochemical derivatization of an iron electrode with p-hydroxymethylbenzenediazonium tetrafluoroborate HOCH₂C₆H₄N₂BF₄. The electrode covered with the HOMB SAM was modified with alkyltriethoxysilanes C_nH_2n+1Si(OC₂H₅)₃ (C_nTES, n = 8 or 18) to prepare a film of one-dimensional polymer. The protective ability of the polymer film was determined by polarization measurement of the covered electrode in an aerated 0.5 M NaCl solution. The ability was enhanced by modification of the HOMB SAM with C_nTES markedly. The iron surface coated with the one-dimensional polymer film of the HOMB SAM modified with C₈TES was characterized by contact angle measurement and FTIR reflection and X-ray photoelectron spectroscopies. The persistence in the protective ability of the polymer film against iron corrosion in 0.5 M NaCl may be associated with the strong adsorption via the covalent bond, revealed by electron-probe microanalysis.     

Growth of Fe on Si (100) at room temperature and formation of iron silicide

Low-energy electron diffraction (LEED), Auger electron spectroscopy and X-ray photoelectron spectroscopy (XPS) investigations of both the growth of an iron film on silicon (100) at room temperature and the subsequent formation of iron silicide are the subjects of this paper. An in-situ cleaned silicon (100) wafer without carbon or oxygen contamination exhibiting the known 2 × 1 reconstruction in the LEED pattern served as the substrate. Iron was deposited on this reconstructed surface at 300 K. The comparison of theoretical calculations based on three growth mechanisms with XPS data obtained with take-off angles of 0° and 50° clearly demonstrates a layer-by-layer growth of the iron film on silicon (100). At 300 K no formation of iron silicide was observed, although an interaction between iron and silicon could be detected at the interface. The formation of iron silicide was observed at annealing temperatures of 630–730 K. Quantitative XPS analysis yields the presence of FeSi₂, when the thickness is large enough. Neither the iron film on silicon nor the silicide shows any LEED pattern.     

Corrosion protection of iron by polypyrrole coatings electrosynthesised from a surfactant solution

This work is a study of the electropolymerisation of pyrrole onto iron electrodes in the presence of sodium bis(2-ethylhexyl) sulfosuccinate in a wide pH interval. The characterisation of the films was done using electrochemical techniques, SEM/EDX and IR spectroscopy. We show that it is possible to synthesise homogeneous, adherent and very compact films in the pH range between 7 and 12 under potentiodynamic, galvanostatic and potentiostatic conditions without substrate dissolution. The effects of various parameters on electrodeposition were investigated. The new procedure for the electrochemical synthesis of polypyrrole results in improved anticorrosion properties. The inhibition is proposed to be due to the sum of a repulsion of chloride ions because AOT remains entrapped in the polymer matrix and the presence of the iron oxide. Advantages of the use of surfactants in the electropolymerisation solution are discussed.     

Action of chelators on solid iron in phosphate-containing aqueous solutions

To study the effect of strong iron-ligands on steel corrosion, mild steel electrodes were immersed in solutions containing 20 mM phosphate buffer (pH=7.2) and between 0.01 mM and 1 M of either the iron(II)-chelators 2,2^′-bipyridine or FerroZine, or the iron(III)-chelators citrate or acetylacetonate. Resulting surface reactions were investigated by quantifying the electrochemical potential (E), the electrochemical polarization resistance (R_p), the corrosion current (I_corr) and the release of iron into solution. The surface was further analyzed by scanning electron microscopy (SEM/SEM-EDAX) and atomic force microscopy. Concentrations of 0.1 mM of any of the chelators led to slight, temporary changes in E, I_corr and R_p. Concentrations of 10 mM resulted in characteristic changes of E, which were the same for all chelators and in the precipitation of FePO₄ in the case of citrate and acetylacetonate, or vivianite [Fe₃(PO₄)₂ · 8H₂O] in the case of bipyridine and FerroZine. Concentrations of 1 mM of both iron(III)-chelators led to a temporary drop of E similar to that found with 0.1 mM chelator. With iron(II)-chelators, E dropped to about −500 mV before oscillating for several days. The amplitudes of the oscillations were up to 200 mV with periods of 30 and 20-25 min for bipyridine and FerroZine, respectively.     

超细铁粉和氧化铁颗粒的研究

用透射电镜和图像分析仪等研究了超细铁粉和γ-Fe_2O_3粉末的结构、形貌、粒子的平均尺寸以及粒度分布。研究结果表明,多数超细铁粉粒子近似呈球形,并且,铁粉粒子由两相组成,粒子的核心部分是金屑a-Fe,表面的包裹层为氧化物层,它由Fe_3O_4和7-Fe_O_3的混合物组成。氧化层的平均厚度大约占整个粒子直径的20％左右。羰基铁粉粒子(含氧化层)的平均直径为16nm。直径在4～24nm范围的粒子数占总粒子数的91％,而7-Fe_2O_3粉末既有雪茄状粒子,也有小球状粒子。分析表明,球状粒子的平均直径为113nm,雪茄状粒子的平均直径(按<长 宽>/2计算)为148nm。由于超细铁粉粒子很细,且有磁性,制备电镜试样时分散比较困难。本文比较了几种分散方法后,使用了一种较好的分散方法——超声喷管分散法。     

Nitrogen addition to iron powder by mechanical alloying

Nitrogen was alloyed into iron (a) by mechanical processing in a nitrogen gas environment, and (b) by mechanically alloying with iron-nitride powders to characterize resulting nano-structure and nitrogen distribution. Although the infused nitrogen concentration was significantly greater than the thermodynamic equilibrium solubility of iron, no nitrides formed, even for nitrogen concentrations as high as 4.1 wt.% However, a bctFe phase did form. Lattice expansion calculations indicate that the sum of the interstitial bcc-Fe and bctFe nitrogen concentrations was significantly less than the total measured nitrogen concentration. A considerable portion of the mechanically infused nitrogen was determined to be associated with nanograin boundaries.