攀钢1450热轧带钢厂精轧机组电动压下机构带钢压下时的动特性计算和探讨

从理论上和实践上对武钢１７００、鞍钢１７００改造前后、本钢１７００改造前后和攀钢１４５０精轧机组的电动压下机构在带钢压下时的动特性进行计算和探讨，得出有说服力的结论。主题词：     

台北101层国际金融中心之结构施工技术与其设计考量概述

本文旨在简要说明目前正在施工中之超高层大楼—台北国际金融中心之结构系统、钢结构工程、钢筋混凝土工程基础与深开挖工程等特殊施工技术,并佐以相关之设计考量与施工规划概要,以供工程界做参考。     

单轴传动滚切式双边剪薄钢板剪后“错牙”及“飞边”的原因分析与对策

针对单轴传动滚切式双边剪生产过程中出现的薄钢板经双边剪剪后出现“错牙”及“飞边”的问题,从多个方面入手对薄钢板出现“错牙”及“飞边”的原因进行了分析对比,提出了相应的解决方案,对今后滚切式双边剪的设计、制造及安装调试有借鉴和参考价值。     

高速钢W6Mo5Cr4V2的脱磷试验

在３０ｋｇ感应炉上用ＣａＯ－Ｎａ２ＣＯ３－ＣａＦ２－ＦｅｘＯ（ＭｏＯ３）渣、ＭｏＣｌ６粉剂和Ａｌ－Ｃａ合金作脱磷剂对高速钢Ｗ６Ｍｏ５Ｃｒ４Ｖ２进行脱磷试验。结果表明，ＣａＯ－Ｎａ２ＣＯ３－ＣａＦ２－ＦｅｘＯ渣的脱磷效果最好，一般脱磷率可达２６％￣５６％。     

Effect of cationic surfactant and inorganic anions on the electrochemical behavior of carbon steel in formation water

Corrosion behavior of carbon steel in formation water associated crude oil from Egyptian western desert was studied at various concentrations of dodecyl dimethyl ammonium chloride (CS) as a cationic surfactant. Polarization curves indicate that CS has a good inhibition efficiency for carbon steel in formation water and behaves as cathodic inhibitor. The inhibition efficiency was found to increase with increase in CS concentration until reaches a maximum constant value corresponding to the critical micelle concentration of CS and decrease with increase in solution temperature. The adsorption of CS follows the kinetic thermodynamic model and Flory-Huggins isotherm. Thermodynamic parameters obtained indicate that that the presence of the CS increases the activation energy. Polarization and Impedance measurements indicate that the addition of KI has a significant synergistic effect with CS and results in increase the inhibition efficiency of CS in formation water.     

转炉出钢口套整体袖砖工艺技术开发

介绍了天津天铁冶金集团有限公司炼钢厂转炉出钢口袖砖工艺的开发过程，主要工艺参数的制定，实践证明，该工艺的应用取得了良好的使用效果。     

Buckling experiments on steel silo transition junctions: I: Experimental results

Large elevated steel silos for the storage of bulk solids generally consist of a cylindrical vessel above a conical discharge hopper supported on a cylindrical skirt. The cone–cylinder–skirt transition junction is subject to a large circumferential compressive force which is derived from the horizontal component of the meridional tension in the conical hopper, so either a ring is provided or the shell walls are locally thickened to strengthen the junction. Extensive theoretical studies have examined the buckling and collapse strengths of these junctions, leading to theoretically based design proposals. However, no previous experimental study on steel silo transition junctions has been reported due to the considerable difficulties associated with testing these thin-shell junctions at model scale. This paper presents the results of a series of tests on cone–cylinder–skirt–ring junctions in steel silos under simulated bulk solid loading. In addition to the presentation of test results including geometric imperfections and failure behavior, the determination of buckling modes and loads based on displacement measurements is examined in detail.     

导磁不锈钢毛的结构化研究

研制了一种新型的结构化钢毛——胶结钢毛。和传统的普通钢毛相比,胶结钢毛具有很强的结构刚度和很低的钢毛流失量;同时,对高岭土有较高的除铁效率。     

铝对W9Mo3Cr4V高速钢组织和硬度的影响

用Ｘ－射线仪，扫描电镜和透射电镜系统研究了铝对钨钼系高速钢铸态，退火以及淬回火组织的影响，铝含量超过２．０％，淬火组织中出现含析出合金的铁素体组织和晶界屈氏体，导致钢硬的降低。     

三辊穿孔和轧管所产生的钢管壁厚极差和波浪形内螺纹

定量描述了实际生产过程中三辊斜轧穿孔所产生的钢管壁厚极差和波浪形内螺纹，初步探讨了三辊轧管机对钢管壁厚极差和波浪形内螺纹的影响。