Emission of trace toxic metals during pulverized fuel combustion of Czech coals

A study of the trace elements emission (As, Se, Cd, Co, Cr, Cu, Zn, Hg, Tl, Pb, Ni, Sn, Sb, V, Mn and Fe) from pulverized coal combustion has been made at six heating and power stations situated in the Czech Republic. The amount of chlorine in coal has considerable influence on volatilization of some elements such as Zn, Cu, Pb, Hg and Tl, which is explained by the formation of thermodynamically stable compounds of these elements with chlorine. Generally, the affinities for Cl follows the order Tl > Cu > Zn > Pb > Co > Mn > Sn > Hg. The experimental data indicates enrichment of some of the trace toxic elements in the emissions (Cu, Zn, As, Se, Cd, Sn, Sb, Hg and Pb) and good agreement was obtained by thermodynamic equilibrium calculations with a few exceptions. In the case of Fe, Mn, Co, Cr and Sn calculated values are overestimated in the bottom ash and there are zero predicted amounts of these elements in the fly ash. In comparison, the results from experiments show up to 80% of these elements retained in fly ash. This implies that there exist additional steps leading to the enrichment by Fe, Mn, Co, Cr and Sn of small particles. Such mechanisms could include the ejection during devolatilization of small inorganic particles from the coal of bottom ash particles, or disintegration of the char containing these metals to small particles of fly ash. On the other hand, there are slightly overestimated or similar values of relative enrichment factors for As, V, Cu, Cd, Sb, Tl and Pb in the fly ashes and zero predicted values for bottom ashes. Our experimental results show about 5% or less of these elements are retained in bottom ashes, so they probably remain in the bottom ash inside unburned parts of coal. Copyright © 2003 John Wiley & Sons, Ltd.     

Electrical/electronic effects of titanium and iron impurities in EFG and FZ solar cell silicon: SPV/EBIC analysis

In this paper results on surface photovoltage (SPV) and electron beam induced conductivity (EBIC) studies of edge-defined film-fed growth (EFG) and floating zone (FZ) silicon solar cell materials (both p-type) are presented. A systematic comparison based on minority carrier diffusion length and carrier recombination is made between: (i) samples contaminated with Ti and/or Fe, (ii) samples gettered by phosphorous diffusion, and (iii) as-received samples. Deep level transient spectroscopy (DLTS) measurements, together with the iron-boron (FeB) pairing kinetics [1] have successfully been used to detect the presence of Fe in the samples. Even though this process is effective in revealing Fe impurities in p-type FZ silicon it is evidently not suitable for Fe identification in p-type EFG silicon. Ti, like Fe, is found to be a prominent lifetime-limiting metallic impurity in both EFG and FZ silicon. Phosphorous diffusion is proven to be an effective external gettering technique for fast-diffusing impurities such as Fe, but not for Ti.     

厚断面球铁的声速

论述了影响厚断面球铁声速和声波衰减的各种因素。指出，必须在应力状态下同时考核声速和声波衰减，以作为判别厚断面球铁材质的一种手段。     

新取代苯基荧光酮试剂的合成及其性质的研究Ⅱ．新型取代苯基荧光酮与金属离子显色反应的研究

研究了３，５－二溴－４－氨基苯基荧光酮、３，５－二溴－４－偶氮变色酸等８种苯基荧光酮在酸性介质中与高价金属离子Ｚｒ（Ⅳ）、Ｍｏ（Ⅵ）、Ｗ（Ⅵ）、Ａｌ（Ⅲ）、Ｇａ（Ⅲ）等的显色反应。３，５－位二溴取代的试剂的灵敏度高于未取代的灵敏度，摩尔吸光系数绝大多数在１０５Ｌ·ｍｏｌ－１·ｃｍ－１以上。     

Organochlorine and Mercury Residues in Young-of-the-Year Spottail Shiners from the Detroit River,Lake St. Clair,and Lake Erie

Young-of-the-year spottail shiners (Notropis hudsonius) were used as biomonitors to determine the spatial distribution (1982/83) and assess trend data for organochlorine and mercury residues. Significantly (p < 0.01) higher PCB residues were found in Detroit River spottail shiners than in collections from southwestern Lake St. Clair and northwestern Lake Erie. The highest PCB residues were found in the west bank collections from Michigan waters (912–2,997ng/g) compared to the mid-stream (96–290 ng/g) and east bank collections (153–316 ng/g). Chlordane residues were found to be elevated in all spottail shiner samples from urbanized areas. Octachlorostyrene and ∑ DDT residues were distributed uniformly within the study area, whereas mercury concentrations were found to be lower in spottail shiners from northwestern Lake Erie than in comparable samples from the Detroit River and southwestern Lake St. Clair. Residues for BHC, heptachlor, aldrin, and chlorinated benzenes were near their detection limits; mirex and chlorinated phenols were not detectable. Recent (1982/83) PCB residue levels in spottail shiners exceeded the IJC aquatic life objective (Great Lakes Water Quality Agreement of 1978) at all the sites sampled, except at Pike Creek in Lake St. Clair. PCB residues in spottail shiners from Pike Creek, Big Creek, and Leamington have declined significantly (p < 0.01) since the mid-seventies. Mercury and chlordane residues have decreased in spottail shiner samples from Leamington, but have remained virtually unchanged at Big Creek and Pike Creek.     

Investigation of the initial stage of borating tantalum

The results of investigation of initial stage of the tantalum borating as well as the effect of oxygen and hydrogen on it are presented. The scheme of the initial stage of tantalum boron saturation is proposed.     

Describing metal surfaces and nanostructures with orbital-free density functional theory

Orbital-free density functional theory (OF-DFT) can be made to scale linearly with sample size, allowing thousands of atoms to be treated explicitly with quantum mechanics. State-of-the-art kinetic energy density functionals and ion–electron pseudopotentials are used to obtain accurate structural property predictions for nanoparticles, nanowires, extended surfaces, and nanoindentation of simple metals.     

Plastic deformation of bcc metal thin foils without dislocation

Heavy plastic deformation of fcc metal thin foils to fracture has been found recently to proceed without involving dislocations, and it results in the formation of high density of vacancy clusters. Thin foil specimens of bcc metals such as V and Mo were plastically deformed to fracture in in situ elongation experiments under an electron microscope. Morphology of thinning and fracture was found to be similar to fcc metals, and no dislocation was observed during heavy deformation. Electron diffraction analysis at the tip of a crack during deformation confirmed a large elastic deformation of up to 5%. Unlike in fcc metal thin foil specimens, point defect clusters were not observed near fractured tips. This difference is attributed to the difference in vacancy reaction, though the deformation in bcc metals without dislocation most likely does produce vacancies.     

Rheology in Processing of in Situ Composites of Polypropylene and Low Melting Poing Metals

The low melting point metallic tin powder or alloy of tin and lead was blended with polypropy-lene. A kind of in situ composite has been prepared. The variations of torque were studied when the composites were mixed in Haake torque rheogeniometer. By way of capillary extrusion, effects upon rheology of the in situ com-posites of the low melting point metals (LMPM) and coupling agent for their different variety and content, were investigated. From flow curves, the results indicate that in situ composites mixed with the LMPM are a kind of pseudoplastic fluid. If the LMPM were melted, the higher the content of the LMPM , the lower apparent viscosity of composites. Meanwhile, when the coupling agent is added into composites, the viscosity of composite will go up first and drop then. This shows that the LMPM have a promoter flow action on the polypropylene.