二价金属离子对UASB颗粒污泥的影响

分析了Mg^2 、Ca^2 、Fe^2 等二价金属离子对UASB反应器中厌氧颗粒污泥的影响。     

Hydrogen Absorption and Release Behavior in Hydrogen Decrepitation Process of Nd-Fe-B Alloys

The behavior of hydrogen absorption and release in hydrogen decrepitation (HD) process of Nd-Fe-B alloys were investigated. The results reveal that the reactivity and the amount of hydrogen absorption in HD process are related to the surface activity of the alloy so that the fresh and active surface has a higher efficiency. The presence of Nd-rich phase at the grain boundary is an essential factor of the HD activity of the alloy at room temperature. On degassing, hydrogen is released from the HD powder continuously with increasing temperature. And the residual hydrogen is as low as 0.0015% at 1073K, which shows that the hydrogen is almost exhaused. It is feasible to remove the hydrogen from the HD powder by heating treatment at the temperature of 523-723K for 1h prior to the magnetic field forming in order to decrease the harmful effect of hydrogen on the easy axis alignment of HD magnet.     

Electrochemical Investigation on the Formation of Dy-Fe Alloy in Molten Chlorides

ＥｌｅｃｔｒｏｃｈｅｍｉｃａｌＩｎｖｅｓｔｉｇａｔｉｏｎｏｎｔｈｅＦｏｒｍａｔｉｏｎｏｆＤｙＦｅＡｌｏｙｉｎＭｏｌｔｅｎＣｈｌｏｒｉｄｅｓＬｉｕＧｕａｎｋｕｎ（刘冠昆），ＴｏｎｇＹｅｘｉａｎｇ（童叶翔），ＨｏｎｇＨｕｉｃｈａｎ（洪惠婵），Ｙａｎｇ...     

臭氧在食品加工用水处理工程上的应用

本文叙述了臭氧的一些特性 ,并以烟台某食品加工公司食品加工用水处理工程为例 ,介绍了臭氧的产生及应用情况 ,提供了处理前后水中各项指标的对照     

压力对Fe－29wt％Ni合金超细微粒特性的影响

利用蒸发冷凝法，制备了不同平均粒径的Ｆｅ－２９ｗｔ％Ｎｉ合金超细微粒。在不同压强下，将超细微粒压制成片。随压强增大，马氏体体积分数和比饱和磁化强度σｓ明显增大，而矫顽力Ｈｃ呈线性下降。压力效应与平均粒径ｄ大小密切相关     

Thermally stimulated discharge current studies in pure and fe-doped polystyrene films

Studies were made on the thermally stimulated discharge currents (TSDCs) in pure (undoped) and Fe-doped polystyrene films as a function of polarizing field, polarizing temperature and dopant concentration. While undoped films exhibited a single peak, doped films showed two peaks one at low temperatures and another at high temperatures. The low temperature peak, which exhibits a shift towards lower temperatures with increasing dopant concentration, is attributed to the relaxation of the main chain, while the high temperature peak, which shows a tendency to shift towards higher temperatures with dopant concentration, is due to space charge polarization. The TSDCs were higher for low dopant concentrations than their undoped counterparts, while for high concentrations of the dopant, the TSDCs decreased. Formation of charge transfer complexes at low dopant concentrations and molecular aggregates at higher dopant concentrations are suggested as the possible reasons for this behaviour.     

Synthesis and characterization of polyaniline films using Fenton reagent

The chemical oxidation of aniline to form polyaniline (PANI) films and powder samples was made using Fenton reagent as an oxidizing agent in aqueous sulfuric acid medium. The PANI films were monitored by using the quartz crystal microbalance and the electronic absorption techniques. The optimum concentration was determined and the results were justified by measuring the UV–vis absorption spectra for the in situ PANI films. The conductivity for the PANI films and powder samples, prepared in different conditions, was measured. Also, the IR spectra, X‐ray and the thermogravimetric analysis for the PANI powder formed in the bulk were measured and compared with the polymer prepared using ammonium peroxydisulfate. A preliminary investigation to the dielectric properties of the polymer powder was measured and discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.     

Effect of Post Annealing on the Microstructure and Magnetic Properties of NdFeB/α-Fe/NdFeB Thin Films

A series of nanocomposite thin films, composed of Nd2Fe14B and α-Fe, has been prepared by DC-magnetron sputtering combined ion beam sputtering onto Si (100) substrates. The effects of post annealing on the microstructure and magnetic properties of [NdFeB/α-Fe/NdFeB]-type thin films have been investigated. The X-ray diffraction (XRD) study showed that annealing of the films for 30min at temperatures 550,600,650,700℃ resulted in the appearance of diffraction peaks, characteristic for Nd2Fe14B tetragonal structure, α-Fe and Nd2O3 phases. The investigation using the Vibrating Sample Magnetometer (VSM) with a maximum applied field of 2 T indicated that with the increase of the annealing temperature, the magnetic properties of the multilayer films were improved and reached peak value at 650℃ (Hci=41.72kA·m-1, Mr/Ms=0.4, (BH)max=30.35kJ·m-3), after which the magnetic properties were decreased greatly. Along with the increase of the thickness of α-Fe layer from Tα-Fe16nm, the coercivity Hci, saturation magnetization Ms, and remanence ratio Mr/Ms all declined. As the Atomic Force Microscope (AFM) indicated, after being annealed at 650℃ for 30min, the sample was showed fine surface morphology with grain size 60nm≤dα-Fe≤80nm and 100nm≤dNdFeB≤150nm.