攀钢1450热轧带钢厂精轧机组电动压下机构带钢压下时的动特性计算和探讨

从理论上和实践上对武钢１７００、鞍钢１７００改造前后、本钢１７００改造前后和攀钢１４５０精轧机组的电动压下机构在带钢压下时的动特性进行计算和探讨，得出有说服力的结论。主题词：     

台北101层国际金融中心之结构施工技术与其设计考量概述

本文旨在简要说明目前正在施工中之超高层大楼—台北国际金融中心之结构系统、钢结构工程、钢筋混凝土工程基础与深开挖工程等特殊施工技术,并佐以相关之设计考量与施工规划概要,以供工程界做参考。     

单轴传动滚切式双边剪薄钢板剪后“错牙”及“飞边”的原因分析与对策

针对单轴传动滚切式双边剪生产过程中出现的薄钢板经双边剪剪后出现“错牙”及“飞边”的问题,从多个方面入手对薄钢板出现“错牙”及“飞边”的原因进行了分析对比,提出了相应的解决方案,对今后滚切式双边剪的设计、制造及安装调试有借鉴和参考价值。     

Behaviors of concrete-filled steel tubular members subjected to combined loading

The present study is an investigation on the behaviors of concrete-filled thin-walled steel tubular members subjected to combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. ABAQUS software is used in this paper for the finite element analysis (FEA). A comparison of results calculated using this modeling shows generally good agreement with test results. The FEA modeling is then used to investigate the influence of important parameters that determine the ultimate strength of the composite members under combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. The parametric studies provide information for the development of formulae for calculating the ultimate strength of the composite members subjected to combined loading.     

Evaluation of Laminated Circular Elastomeric Bearings

This paper evaluates the behavior and performance of laminated circular elastomeric bearings and compares them to those of square and rectangular bearings. The study included an experimental evaluation and a nationwide survey of state Department of Transportations on the use and performance of circular bearings and bearings in general in their states. The experimental investigation studied the bearings' behavior in compression, compression and rotation, and compression and shear. Results from this limited study showed that the three bearings have similar stress-strain behavior in compression and they are in agreement with the AASHTO LRFD guide stress–strain curves. In compression and rotation, the AASHTO LRFD substructure moments are slightly less than the measured values for circular bearings and rectangular bearings rotated about their strong axis for a compressive stress of 10.3?MPa (1.5?ksi) and slightly higher than those of rectangular bearings rotated about their weak axis. In compression and shear, the shear stiffness of circular and square bearings is in agreement with theoretical values within the range of design displacements. Results from the survey showed that many states are using circular bearings and more states would consider using them, however no maintenance or monitoring data were available on their short-term and long-term performance.     

高速钢W6Mo5Cr4V2的脱磷试验

在３０ｋｇ感应炉上用ＣａＯ－Ｎａ２ＣＯ３－ＣａＦ２－ＦｅｘＯ（ＭｏＯ３）渣、ＭｏＣｌ６粉剂和Ａｌ－Ｃａ合金作脱磷剂对高速钢Ｗ６Ｍｏ５Ｃｒ４Ｖ２进行脱磷试验。结果表明，ＣａＯ－Ｎａ２ＣＯ３－ＣａＦ２－ＦｅｘＯ渣的脱磷效果最好，一般脱磷率可达２６％￣５６％。     

Effect of cationic surfactant and inorganic anions on the electrochemical behavior of carbon steel in formation water

Corrosion behavior of carbon steel in formation water associated crude oil from Egyptian western desert was studied at various concentrations of dodecyl dimethyl ammonium chloride (CS) as a cationic surfactant. Polarization curves indicate that CS has a good inhibition efficiency for carbon steel in formation water and behaves as cathodic inhibitor. The inhibition efficiency was found to increase with increase in CS concentration until reaches a maximum constant value corresponding to the critical micelle concentration of CS and decrease with increase in solution temperature. The adsorption of CS follows the kinetic thermodynamic model and Flory-Huggins isotherm. Thermodynamic parameters obtained indicate that that the presence of the CS increases the activation energy. Polarization and Impedance measurements indicate that the addition of KI has a significant synergistic effect with CS and results in increase the inhibition efficiency of CS in formation water.     

汽轮机轴承烧瓦与轴颈的渗巴氏合金现象

简述轴承工作性质，巴氏合金应用与相组成的基本情况。论述汽轮机转子在两个电厂长期运行后，由于轴颈发生的不正常摩擦损伤，在大修改造中由无损检查、机械加工揭示出轴颈存在严重的渗巴氏合金现象，低熔点金属Sn、Sb与Cu向转子材料晶界的深层渗入最终导致了3根大型在投转子的严重开裂与报废。图11表2     

离子束混合工艺对材料抗蚀性能的影响

本文介绍了离子束混合工艺方法。与直接注入相比较,离子束混合所使用的设备造价低1/4—1/2,而生产效率可提高1—2个数量级,因而使生产成本大幅度降低,这无疑对离子束工艺的实际应用将产生巨大的促进作用。 通过对轴承材料(GCr15和Cr4Mo4V)经Cr、N、Ta不同元素的混合处理后,在0.5M H_2SO_4和0.1M NaCl的缓冲溶液中的阳极极化曲线表明经混合处理后的两种材料试样,其抗蚀能力和抗点蚀能力均大大提高,这与直接注入的试样效果是一致的。 通过俄歇谱仪和透射电镜的分析结果表明混合是成功的,且在一定的条件下,形成非晶组织。 本文的结论是,无论是离子的直接注入还是离子束混合,对提高轴承材料的抗腐蚀性能都是有效的方法,特别是离子束混合技术具有更大的应用前景。     

Buckling experiments on steel silo transition junctions: I: Experimental results

Large elevated steel silos for the storage of bulk solids generally consist of a cylindrical vessel above a conical discharge hopper supported on a cylindrical skirt. The cone–cylinder–skirt transition junction is subject to a large circumferential compressive force which is derived from the horizontal component of the meridional tension in the conical hopper, so either a ring is provided or the shell walls are locally thickened to strengthen the junction. Extensive theoretical studies have examined the buckling and collapse strengths of these junctions, leading to theoretically based design proposals. However, no previous experimental study on steel silo transition junctions has been reported due to the considerable difficulties associated with testing these thin-shell junctions at model scale. This paper presents the results of a series of tests on cone–cylinder–skirt–ring junctions in steel silos under simulated bulk solid loading. In addition to the presentation of test results including geometric imperfections and failure behavior, the determination of buckling modes and loads based on displacement measurements is examined in detail.