稠油微生物开采技术现状及进展

综述了用微生物方法开采稠油的技术现状与进展，论题如下。①概述。②基本方法：异源微生物采油，包括微生物吞吐和微生物驱；本源微生物采油压大港孔店油田的实例。③主要机理，包括产表面活性剂，降解稠油中重质组分及其他。④技术研究，包括机理性、可行性及经济效益研究，列举了国内外6个实例。⑤现场应用，包括国外1个、国内6个实例。⑥该技术的优势及问题。参22。     

TUD-DNS3脱硝助剂在催化裂化装置的工业应用

TUD-DNS3脱硝助剂在中韩（武汉）石油化工有限公司1号催化裂化装置上进行了工业应用。结果表明：针对两段再生工艺，当系统中助剂占总催化剂藏量的质量分数为2.6%时，烟气脱硫装置外排污水中的氨氮质量浓度由加剂前的100 mg/L下降至40 mg/L以内；助剂的加入降低了CO焚烧炉的炉膛温度，有利于烟气的合格排放，并对装置操作、产品分布及汽油、柴油产品质量无不良影响。     

井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

机械合金化Fe-Ni粉末的相结构

使用XRD和Moessbauer等方法，研究了在Ar气氛下机械合金化Fe—Ni粉末相结构的变化．结果表明，在机械合金化Fe64-Ni36粉末过程中，fcc相的数量随着球磨时间的增加先增加然后减少，与加乙醇球磨Fe64-Ni36的情形相同．当Ni的含量(原子分数)大于50％时，有fcc相、顺磁相和FeNi3形成，当Ni的含量低于50％时，bcc相的数量随着Ni含量减少而增加．Moessbauer谱的结果表明，因球磨时间或Fe、Ni比例的不同，Fe—Ni球磨粉末固溶体具有不同结构的原子配比。     

大块非晶合金的性能、制备及应用

综述了大块非晶合金的性能、制备方法及应用，对比了吸铸法制备的棒状Zr41.2Ti13.8Cu12.5Ni10Be22.5,Zr57Cu20Al10Ni8Ti5,Zr52.5Ti5Cu17.9Ni14.6Al10(原子分数)大块非晶样品的过冷温度区间宽度(△Tx)，给出了3种大块非晶合金系列的热稳定性参数Tg、Tx及△Tx，提出了大块非晶合金领域存在的问题及发展方向．     

套保稠油油田火烧油层可行性分析

从火烧油层的筛选标准、实际地质条件及室内物理模拟实验入手，对该油田火烧可行性进行了分析。分析结果认为，套保油田进行火烧总体上是可行的，在实际火烧时应避开底水的影响，火烧区域应选在构造高部位或仅烧其主力层。     

A One-Dimensional Nonlocal Damage-Plasticity Model for Ductile Materials

This paper presents a new 1-D non-local damage-plasticity deformation model for ductile materials. It uses the thermodynamic framework described in Houlsby and Puzrin (2000) and holds, nevertheless, some similarities with Lemaitre’s (1971) approach. A 1D finite element (FE) model of a bar fixed at one end and loaded in tension at the other end is introduced. This simple model demonstrates how the approach can be implemented within the finite element framework, and that it is capable of capturing both the pre-peak hardening and post-peak softening (generally responsible for models instability) due to damage-induced stiffness and strength reduction characteristic of ductile materials. It is also shown that the approach has further advantages of achieving some degree of mesh independence, and of being able to capture deformation size effects. Finally, it is illustrated how the model permits the calculation of essential work of rupture (EWR), i.e. the specific energy per unit cross-sectional area that is needed to cause tensile failure of a specimen.     

锌电积的节电探讨

分析厂影响锌电积电能消耗的因素，提出了锌电积的节电对策与展望。     

Structural Changes in Titin and Nebulin Filaments Specific to Calcium Ions at 0.1 mM: Factors of Meat Tenderization During Postmortem Aging

ABSTRACT Postmortem structural changes in titin and nebulin filaments were investigated by incubating isolated myofibrils in a solution containing 0.1 mM calcium ions and various concentrations of a protease inhibitor. The inhibition curves showed 2 abnormal steps with increases in the concentration of leupeptin or calpastatin domain I. While the amounts of unchanged titin and nebulin were constant in the 1st step, the 2nd occurred at higher protease inhibitor concentrations. These facts indicated that excess amounts of leupeptin and calpastatin domain I caused deterioration in titin and nebulin properties, thus interfering with the binding of calcium ions. We concluded that the severance of titin and nebulin filaments in the 1st step were induced by calcium ions at 0.1 mM.     

单分散六边形扁平溴碘化银微晶的结构与性能的研究

应用可控双注仪制备了一系列碘含量相同而碘在微晶中分布不同的单分散六边形扁平溴碘化银乳剂。用扫描电镜（ＳＴＥＭ）与Ｘ－射线能谱仪（ＥＤＳ）对单个微晶进行了微区分析，并用介电损耗，微波光导等方法研究了此类乳剂微晶的结构与性能的关系。结果表明：严格控制微晶成核、成熟、生长三个阶段的条件，可制得含六边形颗粒９２％以上的扁平溴碘化银乳剂，颗粒大小变化系数小于１２％。此外碘在微晶中的分布明显影响微晶的电性质和