The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation. 相似文献
A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:
1. 1. the inclusion of creep relaxation
2. 2. the inclusion of external loads on components
3. 3. a more accurate method of calculating thermal stresses due to temperature transients
4. 4. the inclusion of high cycle fatigue terms.
The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.
The site testing provided good practical experience and showed up problems which would not otherwise have been detected. 相似文献
When a microregion in a thin section of frozen-dried and embedded tissue is analysed by the conventional electron-probe X-ray continuum-normalization method, the measured quantity is in mmol of element per kg of embedded specimen. As each microregion contains an unknown amount of embedding medium, this quantity generally lies indeterminately somewhere within the wide range between mmol of element per kg of hydrated tissue and mmol of element per kg of dehydrated tissue. However, if a ‘tag’ element is incorporated in the embedding medium, the contribution of the medium to the local continuum count in each probed field should be measurable, and the X-ray data may then unambiguously yield mmol of element per kg of dehydrated tissue. This result should not be affected by shrinkage on freeze-drying or by incomplete replacement of water by embedding medium. The same X-ray data can additionally provide estimates of mmol of element per unit volume, mmol of element per kg of hydrated tissue and local dry-mass fraction. However, these estimates are subject to errors due to tissue shrinkage, incomplete replacement of water and beam damage. 相似文献
This paper presents a new 1-D non-local damage-plasticity deformation model for ductile materials. It uses the thermodynamic
framework described in Houlsby and Puzrin (2000) and holds, nevertheless, some similarities with Lemaitre’s (1971) approach.
A 1D finite element (FE) model of a bar fixed at one end and loaded in tension at the other end is introduced. This simple
model demonstrates how the approach can be implemented within the finite element framework, and that it is capable of capturing
both the pre-peak hardening and post-peak softening (generally responsible for models instability) due to damage-induced stiffness
and strength reduction characteristic of ductile materials. It is also shown that the approach has further advantages of achieving
some degree of mesh independence, and of being able to capture deformation size effects. Finally, it is illustrated how the
model permits the calculation of essential work of rupture (EWR), i.e. the specific energy per unit cross-sectional area that
is needed to cause tensile failure of a specimen. 相似文献
Isolated rat hearts were subjected to 15, 45, or 60 minutes of global ischaemia and then fixed by perfusion at 37°C with glutaraldehyde containing various amounts of oxygen. This either had been bubbled with 100% oxygen (PO2 620 mm Hg) or with 100% nitrogen (PO2 40 mm Hg) immediately before use, or it had been routinely prepared and stored exposed to atmospheric oxygen (PO2 245 mm Hg). The ultrastructure of myocytes and endothelial cells subjected to 15 minutes of ischaemia was not affected by the treatment of the fixative. However, when the tissue subjected to longer periods of ischaemia was fixed with routinely prepared or oxygen-bubbled glutaraldehyde, ultrastructural changes characteristic of reoxygenation damage were uniformly evident in both the microvasculature and myocytes. These qualitatively distinct changes included mitochondrial swelling, cell swelling, endothelial bleb formation, and narrowing of capillary lumina. These abnormalities were not observed in tissue fixed with nitrogen-bubbled glutaraldehyde. These findings indicate that deliberate steps should be taken to reduce or eliminate dissolved oxygen from the fixatives used to study ischaemic tissues. Otherwise artefactual reoxygenation damage in vitro may occur and make valid ultrastructural interpretation difficult or impossible. 相似文献
The Modified Embedded Atom Method model for Pu metal is revised so that it more accurately captures the behavior of the Ziegler-Biersack-Littmark
model of ion-ion interactions. Two revision are tested with somewhat different stiffnesses in the 2-1000 eV range. The revised
models show higher damage levels at 20 KeV than an earlier model, suggesting that the behavior of the models above 100 eV
is dominating damage production, at least in the earlier stages of the cascade.
Work was performed at Los Alamos National Laboratory under the auspices of the US Department of Energy, under contract DE-AC52-06NA25396. 相似文献