Brittle fracture of high-strength steels at very low temperatures

High-strength steels are used to increase the load carrying capacity of components. However, to guarantee a safe design, it is also necessary to combine high strength with adequate fracture toughness. In this paper, fracture toughness of three high-strength steels with yield strengths ranging from 460 to 890 MPa has been studied at very low temperatures. Taking into account experimental evidence, a new mechanism of cleavage at very low temperatures is proposed. This mechanism considers the possibility of reaching the ideal strength (the stress at which the lattice of a single crystal losses its stability) in the immediate vicinity of the fatigue crack tip. Moreover, a computational model able to calculate the external load needed to produce a catastrophic failure of these steels has been developed.     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

高强度烧结钢

为开拓粉末冶金材料新的应用领域，近年来对高强度烧结钢进行了大量的研究与开发。本文简要介绍Ｈｏｇａｎａｓ公司开发的一些高强粉末冶金材料及对一些高强度烧结材料尺寸变化的控制。     

HSLA-80/100钢的焊接

对ＨＳＬＡ－８０／１００钢的焊接性、焊接材料及焊接工艺进行了综述，并指出了现存在的主要问题。     

Microstructural Modelling of Nb Microalloyed Steels during Thin Slab Direct Rolling Processing

The microstructural evolution during the hot rolling of coarse grain sized austenite has been modeled considering all the microstructural mechanisms (dynamic, static and metadynamic recrystallization, strain induced precipitation) that can take place during an industrial TSDR production of three Nb microalloyed steels. Based on the results obtained from the model, processing maps have been drawn for 0.02%, 0.035% and 0.05% Nb microalloyed steels. Optimum processing conditions to exploit all the benefits of the Nb microalloying have been defined considering a final gauge thickness range between 1.5 and 12.65 mm. In addition, and facing the difficulties present in the production of thick hot strip, several alternative thermomechanical schedules are proposed, which would originate microstructures with a suitable combination of homogeneity and retained strain prior to transformation.     

Microstructures and mechanical properties of welded Fe-12Cr-20Mn austenitic stainless steel

The effects of welding on the tensile and fatigue properties of fully annealed and cold-worked Fe-12Cr-20Mn austenitic stainless steel were evaluated. Room temperature and 500 °C tensile tests and room temperature cantilever beam fatigue tests were accomplished on specimens that contained autogenous bead-on-plate welds. The tensile and fatigue properties of the fully annealed material were not significantly influenced by welding. The tensile properties of the welded cold-worked material were also not significantly affected by the presence of a weldment. However, welding caused a large reduction of the fatigue life of the cold-worked material. Fatigue cracks preferentially initiated at large Mn-Si inclusions that formed in the fusion zones of the weldments.     

Characterization of angular dependence of macroscopic magnetic properties in ASTM 36 steel using magnetic Barkhausen noise

Angular-dependent magnetic Barkhausen noise measurements were performed on ASTM 36 steel samples for various values of applied uniaxial stress. The maximum differential permeability and the coercive field are obtained from this Barkhausen signals. The angular dependence of these macroscopic magnetic properties is studied. The tension for which the magneto-elastic energy balances the anisotropic energy is estimated. The results are discussed based on the domain wall theory.     

Environmental effects on the stress corrosion cracking susceptibility of 3.5NiCrMoV steels in high temperature water

Constant elongation rate tests (CERTs) were carried out to investigate the effects of environmental factors of dissolved oxygen and temperature on the stress corrosion cracking (SCC) susceptibility of 3.5NiCrMoV turbine steels. Tests were conducted in pure water of various dissolved oxygen concentrations at temperatures of 50 °C-200 °C in the range of strain rates from 5 × 10⁻⁸/s to 1 ×  10⁻⁶/s. Dissolved oxygen significantly affected the SCC susceptibility of turbine steels in water. The SCC susceptibility of the turbine steels increases as the dissolved oxygen concentration in water increases. The elongation of the turbine steels tested in aerated water at 150 °C at a strain rate of 1 × 10⁻⁷/s decreased to half of that of the steels tested in deaerated water in the same test condition. And the SCC susceptibility of the steels increased with decreasing strain rate, and with increasing temperature. The increase of the SCC susceptibility of the turbine steels in the higher dissolved oxygen environment is considered to be due to the higher content of dissolved oxygen enhancing the reduction reactions of oxygen on the metal surfaces (cathode) and accelerating the dissolution rate at the crack tips (anode) by galvanic attack of an aeration cell.     

Spheroidization of medium-carbon steels

Spheroidization experiments were made on a medium- carbon AISI 4037 steel, using both intercritical and subcritical annealing cycles. The results indicate that in the subcritical cycle the spheroidization occurred much more quickly than expected, so that shorter times were sufficient to achieve high formability. On the other hand, the hardness dropped faster in the intercritical cycle. Although more work needs to be done, these results suggest that using a subcritical spheroidization process instead of an intercritical process could achieve considerable savings in time, energy, and cost.