Effect of Sb implantation on copper silicides formation and morphology after annealing of Cu/Si structures

In this work, the solid state reaction between a thin film of copper and silicon has been studied using Rutherford backscattering spectroscopy, X-ray diffraction, scanning electron microscopy and microprobe analysis. Cu films of 400 and 900 Å thicknesses are thermally evaporated on Si(1 1 1) substrates, part of them had previously been implanted with antimony ions of 5×10¹⁴ or 5×10¹⁵ at. cm⁻² doses. The samples are heat-treated in vacuum at temperatures in the range 200–700 °C for various times. The results show the growth and formation of Cu₃Si and Cu₄Si silicides under crystallites shape dispatched on the sample surface, independently of the implantation dose. On the other hand, it is established that the copper layer is less and less consumed as the antimony dose increases, resulting in the accumulation of Sb⁺ ions at silicide/Si interface and in the silicide layer close to surface. The exposure of samples to air at room temperature shows the stability of Cu₄Si phase whereas the Cu₃Si silicide disappears to the benefit of the silicon dioxide formation. The observed phenomena are discussed.     

Gamma-irradiation-induced Ag/SiO2 composite films and their optical absorption properties

Small Ag particles or clusters dispersed mesoporous SiO₂ composite films were prepared by a new method: First the matrix SiO₂ films were prepared by sol-gel process combined with the dip-coating technique, then they were soaked in AgNO₃ solutions followed by irradiation of γ-ray at room temperature and in ambient pressure. The structures of these films were examined by X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), and optical absorption spectroscopy. It has been shown that the Ag particles grown within the porous SiO₂ films are very small, and they are isolated and dispersed from each other with very narrow size distributions. With increasing the soaking concentration and an additional annealing, an opposite peakshift effect of the surface plasmon resonance (SPR) was observed in the optical absorption measurements.     

Mechanical behavior of 30–50 nm thick aluminum films under uniaxial tension

We present uniaxial tensile test results for 30–50 nm thick freestanding aluminum films. Young’s modulus and ductility were found to decrease monotonically with grain size. Reverse Hall–Petch behavior was observed with no appreciable room temperature creep. Non-linear elasticity with small irreversible deformation was observed for 50 nm thick specimens.     

薄板坯连铸工艺液芯压下的有限元分析

简要介绍世界几种主要薄板坯连铸工艺。着重叙述应用大型通用商业软件MSC.MARC。模拟液芯压下时铸坯的变形，确定最佳压下方案的有限元分析，液芯压下应该在结晶器出口处及二冷区扇形段开始部分进行，这样能减小铸坯的应变。     

单轴传动滚切式双边剪薄钢板剪后“错牙”及“飞边”的原因分析与对策

针对单轴传动滚切式双边剪生产过程中出现的薄钢板经双边剪剪后出现“错牙”及“飞边”的问题,从多个方面入手对薄钢板出现“错牙”及“飞边”的原因进行了分析对比,提出了相应的解决方案,对今后滚切式双边剪的设计、制造及安装调试有借鉴和参考价值。     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

Breakdown of oil films and formation of residual films

The breakdown processes of oil films under quasi-static loading have been investigated by using a newly developed steel-oil-mercury system. The relationship between the thickness and breakdown ratio of a hexadecane film is represented by a single master curve independently of the indentation speed, indentation load, and temperature. The master curve shows that the breakdown process of hexadecane includes two stages; one is the decrement of the thickness without breakdown and the other is the decrement of the thickness with a drastic progress of breakdown. By solving a small amount of fatty acid in hexadecane, the thickness increases and the breakdown ratio decreases noticeably; a multilayer residual film supporting normal load is formed between two metal surfaces. Experiments at different temperatures reveal a negative relationship between the temperature and thickness of residual film, which indicates that the residual film is organized by physical interaction rather than chemical interaction. At least under a lower concentration, the residual film appears to consist of not only fatty acid molecules but also hexadecane molecules.     

焊接波浪状边缘薄钢带的高上山成型法

介绍了高上山成型法的工艺特点及理论上的可行性和实践中的可靠性，此方法能有效地解决薄钢带波浪状边缘的焊接方面存在的问题。