LPNN-based approach for LASSO problem via a sequence of regularized minimizations

In compressive sampling theory, the least absolute shrinkage and selection operator (LASSO) is a representative problem. Nevertheless, the non-differentiable constraint impedes the use of Lagrange programming neural networks (LPNNs). We present in this article the -LPNN model, a novel algorithm that tackles the LASSO minimization together with the underlying theory support. First, we design a sequence of smooth constrained optimization problems, by introducing a convenient differentiable approximation to the non-differentiable -norm constraint. Next, we prove that the optimal solutions of the regularized intermediate problems converge to the optimal sparse signal for the LASSO. Then, for every regularized problem from the sequence, the -LPNN dynamic model is derived, and the asymptotic stability of its equilibrium state is established as well. Finally, numerical simulations are carried out to compare the performance of the proposed -LPNN algorithm with both the LASSO-LPNN model and a standard digital method.     

光电设备电子机柜布线工艺研究

作为信号和电能载体的导线，同时也是噪声的载体和外来噪声侵入设备的媒体。描述了噪声通过导线侵入设备内部的方式，通过降低噪声的途径确定了机柜布线的原则，介绍了布线的要求和方法，最后提出了用布线槽布线的建议。     

三网互联的几个关键技术

对三网互联的几个关键技术进行分析与研究，介绍利用IP技术解决有线电视网地址选择问题，探讨怎样将ATM技术与IP技术相互融合，使真正的信息高速公路成为现实，阐述利用H．323标准全面解决视频网络方案。     

Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

H.264变换编码与量化原理分析

详细分析了 H .2 64视频编码标准中的整数变换和量化过程。 H .2 64采用 4× 4整数变换 ,并将尺度调整融合在量化过程中 ,降低变换算法复杂度和减少乘法次数 ,相对于以前的编码标准更加有效     

带隔板底水油藏油井临界产量计算公式

本给出了带隔板底水油藏油井的监界产量计算公式，它适用于所有带隔板底水油藏的油井。     

具有阻力特性材料的σ_f－σ关系及一种新的阻力曲线测定方法

通过对相变增韧陶瓷及一种可切削玻璃－陶瓷动态疲劳（恒应力速率）试验中高应力速率区断裂应力下降现象的理论分析，发现这种现象与材料的阻力特性（Ｒ－ｃｕｒｖｅ）密切相关。确立的σ_ｆ－σ理论关系能够很好地描述整个应力速率区间内的动态疲劳试验结果。高应力速率区σ_ｆ－σ在双对数坐标下为负斜率直线，直线斜率为（ｍ为阻力曲线ＫＲ＝ｋ（△ａ）~ｍ的指数），断裂主要由材料阻力行为控制；低应力速率区，σ_ｆ－σ在双对数坐标下为正斜率直线，直线斜率为　（ｎ为应力腐蚀指数），断裂主要由材料应力腐蚀行为控制。建立了测定材料阻力特性的一种新方法，分别用这种方法及压痕／弯曲方法对一种可切削玻璃－陶瓷的阻力特性进行了实验测定，两种方法所得结果有很好的一致性。     

氧化铝陶瓷缺口件循环疲劳及断裂机理

用实验方法研究了Ａｌ＿２Ｏ＿３陶瓷缺口试件在循环载荷作用下的疲劳寿命。结果表明，缺口导致的应力集中效应显著降低了循环疲劳寿命；若用缺口根部最大应力为应力水平，则不同缺口半径陶瓷试件具有相同疲劳断裂规律，说明陶瓷材料的疲劳集中系数和理论应力集中系数相同。本文还分析讨论了陶瓷材料的循环疲劳寿命表达式和循环疲劳断裂机理。     

Microwave Communication to Moving Parts Inside Machines

Cables to moving parts on a linear actuator in production machines, such as pick-and-place machines, are a source of unreliability owing to the possible breaking of a cable. They further reduce the positioning precision of the actuator owing to additional forces. Slotted waveguide systems for rail vehicles based on 2.4 GHz transmission frequency are well known, but transmitters/receivers and waveguides are bulky. The paper reports on the reduction in size of the equipment, adapted to 5.8 GHz using a commercial off-the-shelf RadioLan communication module. Further, the efficient termination of the wave-guide and a new way to reduce standing-wave effects is also discussed.