Quantitative evaluation of two-dimensional dynamic deformations using digital holography

An optical system for the parallel evaluation of in- and out-of-plane dynamical deformations will be described. A double pulse laser with pulse separation in the microsecond range is used for the investigations. Two separate interferograms of an object under test, in its undeformed and deformed state, are recorded in a few microseconds. The object is illuminated from two different directions and imaged onto a CCD sensor. This produces two sensitivity vectors. The reference beams have different directions in order to produce two directional spatial carriers. The Fourier method is used for quantitative evaluation, and the measurements along different sensitivity vectors are separated in the Fourier domain. The phases of the two interferograms are obtained from the complex amplitudes and the two dimensional deformation is calculated from the phases. Experimental results are presented.     

基于斜向背散射偏振拉曼光谱的{100}c-Si面内应力分析

复杂应力状态下应力分量的解耦分析对半导体的设计和制造具有重要意义。本文开展了方法学研究,首先建立了{100}晶面族单晶硅面内应力分量解耦分析模型,基于该模型,通过改变入射光和散射光的几何构型和偏振构型,可得到单晶硅拉曼频移与应力分量的解析关系。在此基础上,提出了一种利用斜向背散射偏振拉曼光谱在不同倾角、偏振方向和样品旋转角度下开展原位拉曼探测实现应力分量解耦分析的实用技术。本文通过实验验证了该方法的可靠性和适用性。     

In-plane bistatic backward scattering from seabottom with randomly inhomogeneous sediment and rough interface

1 Introduction Backward scattering of sound due to sediment is the main source of shallow waterreverberation. In order to predict the reverberation or detect sediment properties frommeasured reverberation data, a reasonable in-plane bistatic backward scattering (BBS)model is essential. The scattering can be caused by the roughness of water-sediment in-terface or by inhomogeneities within the volume of sediment. A great deal of researchhas been done on sediment backscattering, most of which h…     

Determination of the in-plane anisotropy field in hexagonal systems via rotational magnetization: Theoretical model and Monte Carlo simulations

The magnetic anisotropy field in thin films with in-plane uniaxial anisotropy can be deduced from the VSM magnetization curves measured in magnetic fields of constant magnitudes. This offers a new possibility of applying rotational magnetization curves to determine the first- and second-order anisotropy constant in these films. In this paper we report a theoretical derivation of rotational magnetization curve in hexagonal crystal system with easy-plane anisotropy based on the principle of the minimum total energy. This model is applied to calculate and analyze the rotational magnetization process for magnetic spherical particles with hexagonal easy-plane anisotropy when rotating the external magnetic field in the basal plane. The theoretical calculations are consistent with Monte Carlo simulation results. It is found that to well reproduce experimental curves, the effect of coercive force on the magnetization reversal process should be fully considered when the intensity of the external field is much weaker than that of the anisotropy field. Our research proves that the rotational magnetization curve from VSM measurement provides an effective access to analyze the in-plane anisotropy constant K ₃ in hexagonal compounds, and the suitable experimental condition to measure K ₃ is met when the ratio of the magnitude of the external field to that of the anisotropy field is around 0.2. Supported by the National Natural Science Foundation of China (Grant Nos. 90505007 and 10774061) Recommended by LI FaShen     

Microstructure and strain films using in-plane grazing analysis of GaN epitaxial incidence x-ray diffraction

This paper investigates the major structural parameters, such as crystal quality and strain state of （001）-oriented GaN thin films grown on sapphire substrates by metalorganic chemical vapour deposition, using an in-plane grazing incidence x-ray diffraction technique. The results are analysed and compared with a complementary out-of-plane x- ray diffraction technique. The twist of the GaN mosaic structure is determined through the direct grazing incidence t of （100） reflection which agrees well with the result obtained by extrapolation method. The method for directly determining the in-plane lattice parameters of the GaN layers is also presented. Combined with the biaxial strain model, it derives the lattice parameters corresponding to fully relaxed GaN films. The GaN epilayers show an increasing residual compressive stress with increasing layer thickness when the two dimensional growth stage is established, reaching to a maximum level of-0.89 GPa.     

Blue-phase liquid crystal display with insulating protrusion

In order to lower the saturation voltage and enhance the transmittance of in-plane switching blue-phase liquid crystal display (IPS-BPLCD), IPS-BPLCD with insulating protrusion is proposed. The single-protrusion (only set on the top of pixel electrode) and double-protrusion (set on the top of pixel and common electrodes) structures are investigated in this work. The potential distribution changes when the protrusion is used. There is a thicker transverse electric field in BPLC range, because the stronger electric field at the edges of the electrodes is decentralised into BPLC range. As a result, the saturation voltage is reduced from 36.3 V to 28.9 V when the double-protrusion structure is used, and transmittance is increased by ~20%. The contrast ratio is larger than 1000:1 in 60° viewing cone using a half-wave biaxial film. Both single-protrusion and double-protrusion structures have the uniform gamma curves at large oblique viewing angles. Moreover, the off-axis image distortion index is 0.1590 at 60º polar angle when zigzag electrodes are used.     

A new standing-wave-type linear ultrasonic motor based on in-plane modes

This paper presents a new standing-wave-type linear ultrasonic motor using combination of the first longitudinal and the second bending modes. Two piezoelectric plates in combination with a metal thin plate are used to construct the stator. The superior point of the stator is its isosceles triangular structure part of the stator, which can amplify the displacement in horizontal direction of the stator in perpendicular direction when the stator is operated in the first longitudinal mode. The influence of the base angle θ of the triangular structure part on the amplitude of the driving foot has been analyzed by numerical analysis. Four prototype stators with different angles θ have been fabricated and the experimental investigation of these stators has validated the numerical simulation. The overall dimensions of the prototype stators are no more than 40 mm (length) × 20 mm (width) × 5 mm (thickness). Driven by an AC signal with the driving frequency of 53.3 kHz, the no-load speed and the maximal thrust of the prototype motor using the stator with base angle 20° were 98 mm/s and 3.2 N, respectively. The effective elliptical motion trajectory of the contact point of the stator can be achieved by the isosceles triangular structure part using only two PZTs, and thus it makes the motor low cost in fabrication, simple in structure and easy to realize miniaturization.     

A transflective and viewing angle controllable blue-phase liquid crystal display

A polymer-stabilised blue-phase liquid crystal display (PSBP-LCD) with double-side in-plane switching (DS-IPS) electrode structure is proposed. This structure shows the transflective characteristics because the bottom electrodes are made by aluminium material. For transflective displays, it exhibits a well-matched voltage-dependent transmission and reflection curves through designing the width and gap of the top electrodes. When a bias voltage is applied on the top electrodes, it exhibits as a good viewing angle controllable display.     

部分相干光云纹干涉法测三维位移场

本文提出了一种用部分相干光可同时获得面内位移和离面位移场的云纹干涉法。该法具有装置简单,无需防震,可用于观场测量等特点。文中论述了此法的基本原理,应用波前干涉理论和付里叶光学理论对变形前后波前的干涉、记录和再观进行了分析,导出了计算公式。实现了透射物体和反射物体表面的面内位移分量(U_0,V_(45),U_(90))和离面位移(w)的全场同时测量,典型实验证明,实验值与计算结果符合较好。     

Spin–orbit coupling effects on the in-plane optical anisotropy of semiconductor quantum wells

We theoretically study the influence of the spin–orbit coupling(SOC) on the in-plane optical anisotropy(IPOA) induced by in-plane uniaxial strain and interface asymmetry in(001) GaAs/AlGaAs quantum wells(QWs) with different well width. It is found that the SOC has more significant impact on the IPOA for the transition of the first valence subband of heavy hole to the first conduction band(1H1E) than that of 1L1E. The reason has been discussed. The IPOA of(001) InGaAs/InP QWs has been measured by reflectance difference spectroscopy, whose amplitude is about one order larger than that of GaAs/AlGaAs QWs. The anisotropic interface potential parameters of InGaAs/InP QWs are also determined. The influence of the SOC effect on the IPOA of InGaAs/InP QWs when the QWs are under tensile, compressive or zero biaxial strain are also investigated in theory. Our results demonstrate that the SOC has significant effect on the IPOA especially for semiconductor QWs with small well width, and therefore cannot be ignored.