热丝加热电流对CH薄膜沉积速率和表面形貌的影响

 热丝辅助裂解法是结合气相沉积制备聚对二甲苯薄膜和热丝化学气相沉积而形成的一种制-CH薄膜的新方法。热丝辅助裂解法的最大特点就是在保持低衬底温度情况下可以获得高沉积速率，而热丝加热电流对薄膜沉积速率和薄膜表面形貌具有重要影响。研究表明，热丝加热电流越大，薄膜沉积速率越高，在加热电流9A时，薄膜沉积速率可达0.002mm/min，同时薄膜表面粗糙度随之增加，薄膜表面也开始出现其它元素污染，因此，一般热丝加热电流选择为7A附近。     

FTIR measurements of CO2 line positions and intensities at high temperature in the 3700-3750 cm spectral region

Positions and intensities for 453 spectral lines in 12 rovibrational bands of ¹²C¹⁶O₂ have been determined between 3700 and 3750 cm⁻¹. At three temperatures (294, 500, and 698 K) eight spectra have been recorded at a pressure around 5 mbar and for an absorption path of about 190 cm⁻¹ using a Bomen DA3 Fourier transform spectrometer (4 × 10⁻³ cm⁻¹ resolution). Some of the measured positions and intensities can be compared with recent experimental results that validate the experimental set-up and the data analysis procedure. The results are also compared with the values listed in the HITRAN 2000 database. If the agreement is generally good, discrepancies are observed for three hot bands.     

“阳”加速器钼丝X-pinch初步实验研究

 在“阳”加速器上进行了直径分别为10, 15, 20 μm, 交叉角为32°,45°,60°的钼（Mo）丝X-pinch实验。“阳”加速器产生的电流峰值约520 kA，上升时间80 ns。实验中通过X射线功率谱仪和纳秒分幅相机等仪器对Mo丝X-pinch辐射特性进行了诊断。实验表明：Mo丝X-pinch过程中会出现多次X射线爆发，箍缩过程中产生的热点辐射出能量超过3 keV的X射线，探测到的最小热点直径小于30 μm。     

金锥对靶背向超热电子分布的影响

 采用20 TW啁啾脉冲放大的ps激光辐照金锥靶和平面靶，对靶背向产生的超热电子角分布和能谱进行了实验研究。结果表明:金锥对超热电子的产生具有重要的影响。与平面靶情况相比，锥形靶靶背向产生的超热电子数量增加，电子能量为2.0~2.5 MeV的超热电子数目有大幅度增长；锥形靶背向超热电子的空间发散角大于平面靶,这是由于啁啾脉冲放大激光所固有的较高脉冲前沿产生的预等离子体造成的影响。     

HER磁镜上硬X射线和热电子测量

一、引言 磁镜运行中,为了要知道它在电子回旋共振加热(ECRH)下形成热电子的参数,我们测量了硬X射线能谱、硬X射线发射的时间特性、不同磁场强度下形成热电子环的位置、以及热电子的脉冲幅度分布等。 HER是中国科学院等离子体物理研究所简单型磁镜装置,它的几何尺寸是,真空室长     

Influence of chemistry and hot rolling conditions on high permeability non-grain oriented silicon steel

This paper discusses the influence of chemical composition on the final electromagnetic properties in higher permeability material. Furthermore, the effect of the hot rolling practice and the end of austenite transformation temperature range on the hot band microstructure is described. The magnetic polarization J₅₀₀₀ better than 1.7 T, using hot rolling conditions 40 mm transfer bar thickness, finish mill entry temperature 1000 °C, and finishing temperature 800–840 °C and after decarburization heat treatment and grain growth treatment, was obtained.     

Cathodic electrochemiluminescence at double barrier Al/Al2O3/Al/Al2O3 tunnel emission electrodes

Double insulating barrier tunnel emission electrodes were fabricated by adding a new pure aluminum layer upon oxidized aluminum electrodes by vacuum evaporation and thermally oxidizing the new aluminum layer in air at room temperature. Resulting Al/Al₂O₃/Al/Al₂O₃ electrodes allow the use of various aluminum alloys in the electrode body necessary for hardness or shaping ability of the electrode while obtaining the luminescence properties of pure aluminum oxide. During electrical excitation of luminescent labels by cathodic hot electron injection into aqueous electrolyte solution, the background noise is mainly based on high-field-induced solid-state electroluminescence and F-center luminescence of the outer aluminum oxide film. The more defect states and/or impurity centers the outer oxide film contains, the higher is the background emission intensity. The present electrode fabrication method provides a considerable improvement in signal-to-noise ratio for time-resolved electrochemiluminescence (TR-ECL) measurements when the original native oxide film of the electrode body contains luminescence centers displaying long-lived luminescence. The excellent performance of the present electrodes is demonstrated by extremely low-level detection of Tb(III) chelates, luminol, Pt(II) coproporphyrin and Tb(III) labels in an immunometric immunoassay by time-resolved electrochemiluminescence.     

Heterogeneous and homogeneous electrochemiluminoimmunoassays of hTSH at disposable oxide-covered aluminum electrodes

Heterogeneous and homogeneous immunoassays of human thyroid stimulating hormone (hTSH) were developed on immunometric basis using aromatic Tb(III) chelates as electrochemiluminescent labels and varied types of disposable oxide-covered aluminum electrodes as the solid phase of the immunoassays. The long luminescence lifetime of the present labels allows the use of time-resolved electrochemiluminescence detection and provide the low detection limits of these labels and, thus, sensitive immunoassays. The primary antibody of immunometric immunoassays was coated upon aluminum oxide surface by physical absorption. In homogeneous immunoassays using 66 μl cell and 15 min incubation time, a linear calibration range of 0.25-324 μU/ml was obtained by applying only a single cathodic excitation pulse in the detection step of the assay.     

Anodic behavior of nickel-based alloys in the electrolytic production of NF3

The Ni-based alloys, such as Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si, prepared by hot isostatic pressing (HIP) at 1000 °C under 2 × 10⁸ Pa for 2 h were employed as the anodes for electrolytic production of NF₃. The current efficiencies for NF₃ formation were 42-38, 52-40, 52-47, 63-62, 50 and 41% for Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloys, respectively. The current efficiencies only on Ni-Cu alloys with Cu concentrations lower than 10 mol% were almost the same as those on Ni sheet and HIPed Ni anodes, whereas those on the other alloys used in this study were smaller compared with those on both Ni anodes. On the other hand, the current losses caused by anodic dissolution of Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloy electrodes were 7.95-4.42, 6.40-7.02, 5.60-6.30, 3.34-6.33, 5.10 and 0.18%, respectively. The anode consumptions of Ni-5 mol% Cu and Ni-5 mol% Si alloys were almost the same or smaller compared with those of Ni sheet and HIPed Ni electrodes, though those of other alloys used were large compared with those of both Ni anodes. Consequently, addition of Cu to the nickel matrix is available for a cheaper cost of anode with keeping a same current efficiency as that on the Ni anode and addition of Si to the nickel matrix is effective for decreasing anode consumption largely. A Ni sheet electrode containing a trace of impurities, such as Co, Mn, Ag and Al, is also favorable as the anode for electrolytic production of NF₃.