固体力学有限元体系的结构拓扑变化理论

本文是文[1]的继续.文[1]提出了杆件系统的结构拓扑变化理论和拓扑变化法本文将这一理论和方法推进到连续体有限元体系;且在此基础上揭示出有限元体系的一个新性质,称为基本位移之梯度的正交性定理,从而给出一套设计敏度的显式表达式,可直接用于计算.     

Effect of absorbed pump power on the quality of output beam from monolithic microchip lasers

The dependence of the beam propagation factor (M ² parameter) with the absorbed pump power in the case of monolithic microchip laser under face-cooled configuration is extensively studied. Our investigations show that the M ₂ parameter is related to the absorbed pump power through two parameters (α and β) whose values depend on the laser material properties and laser configuration. We have shown that one parameter arises due to the oscillation of higher order modes in the microchip cavity and the other parameter accounts for the spherical aberration associated with the thermal lens induced by the pump beam. Such dependency of M ² parameter with the absorbed pump power is experimentally verified for a face-cooled monolithic microchip laser based on Nd³⁺ -doped GdVO₄ crystal and the values of α and β parameters were estimated from the experimentally measured data points.     

CONCEPTUAL DESIGN STUDIES OF AN 84 GHz, 500 kW, CW GYROTRON

The feasibility of an 84 GHz, 500 kW, CW gyrotron for ECRH on an experimental tokamak will be presented in this paper. Mode competition and mode selection procedures are carefully investigated by considering various candidate modes and the TE_10,4 mode is chosen as the operating mode. A conventional cylindrical cavity resonator with weak input and output tapers and parabolic roundings is considered for interaction studies. Self-consistent, both single mode and time-dependent, calculations are carried out and power and efficiencies are computed for a typical set of beam parameters. The results show that an output power of well over 500 kW, CW and efficiency around 40% can be reached without a depressed collector.     

激光除冰研究

架空输送电线路因覆冰而导致的事故危害性很大,本文总结了目前国内外输电线路导线覆冰的现状。统计国内外探索出来的各种预防,融化,除冰等很多解决方案。通过研究和探讨,分析导线覆冰的传热和能量,运用了多种激光器进行激光熔(除)冰实验,比较研究二氧化碳激光器的除冰情况。以及提出激光熔冰的方法、研究方向和前景。     

Effect of the Parameters of Three-Mirror Resonators on the Spectral Characteristics of Single-Pulse Laser Generation with Self-Injection of Priming Radiation

Based on a semiclassical theory, investigations were made of the dynamics and spectral composition of pulsed generation with self-injection of priming radiation from the active part of a three-mirror linear resonator, the passive part of which contains an active loss modulator and serves as the output reflector of the laser. It is shown that there exists a range of resonator parameters at which pulsed lasing has virtually a single frequency irrespective of the detuning of the frequencies of the priming radiation and of the nearest eigenmode of the composite resonator. Considering graphically the phase conditions of generation, it is established that among pulsed lasers with self-injection of priming radiation which are constructed on the basis of three-mirror linear and branched resonators, the most efficient for creating single-frequency generation are those in which the length of the main resonator, where generation of the pulse occurs, is larger than the length of the additional one intended for forming the priming radiation. With an inverse ratio of the lengths of the resonators, the conditions of single-frequency pulsed generation becomes dependent on the priming radiation frequency.     

Extrusion of pastes with a piston extruder for the determination of the local solid and fluid concentration, the local porosity and saturation and displacement profiles by means of NMR imaging

 Nuclear Magnetic Resonance (NMR) was used to investigate the extrusion behaviour of PTFE pastes in a ram extruder. By means of ¹H-NMR imaging (MRI) it is possible to determine the local proton density and therefore, the local fluid concentration. The ¹⁹F-MRI provides the local solid concentration. Thus the local saturation and the local porosity can be calculated with the information of the local fluid and solid concentration. Furthermore displacement profiles can be derived from NMR images by means of correlation techniques without any preparation or marking of the pastes. Received: 8 May 2000   Accepted: 1 May 2001     

Nonsensitiveness Regions for Threshold Ellipsoids

The problem is to determine nonsensitiveness regions for threshold ellipsoids within a regular mixed linear model.     

High pressure X-ray diffraction study of CdAl2Se4 and Raman study of AAl2Se4 (A=Hg, Zn) and CdAl2X4 (X=Se, S)

We report the results of an X-ray diffraction study of CdAl₂Se₄ and of Raman studies of HgAl₂Se₄ and ZnAl₂Se₄ at room temperature, and of CdAl₂S₄ and CdAl₂Se₄ at 80 K at high pressure. The ambient pressure phase of CdAl₂Se₄ is stable up to a pressure of 9.1 GPa above which a phase transition to a disordered rock salt phase is observed. A fit of the volume pressure data to a Birch-Murnaghan type equation of state yields a bulk modulus of 52.1 GPa. The relative volume change at the phase transition at ∼9 GPa is about 10%. The analysis of the Raman data of HgAl₂Se₄ and ZnAl₂Se₄ reveals a general trend observed for different defect chalcopyrite materials. The line widths of the Raman peaks change at intermediate pressures between 4 and 6 GPa as an indication of the pressure induced two stage order-disorder transition observed in these materials. In addition, we include results of a low temperature Raman study of CdAl₂S₄ and CdAl₂Se₄, which shows a very weak temperature dependence of the Raman-active phonon modes.     

Diode-pumped 671 nm laser frequency doubled by CPM LBO

A design of diode-pumped high-efficiency Nd:YVO₄/LBO red laser is reported. Using critical phase-matching (CPM) LBO, 671 nm red laser was obtained from 1342 nm light by intracavity frequency doubling. With an incident pump laser of 800 mW, using type-I and type-II CPM LBO, 97 and 52 mWTEM₀₀ mode red laser outputs were obtained, with optical-to-optical conversion efficiencies of up to 12.1% and 6.5%, respectively.     

High-throughput screening of fuel cell electrocatalysts

The drawbacks of our earlier report of preparing fuel cell catalyst arrays by borohydride reduction of inkjet prepared arrays of metal salts are discussed along with the need for inclusion of state-of-the-art metrics in all array screening. An alternative method for screening of hydrogen/air cathode catalysts, direct methanol fuel cell (DMFC) anode catalysts, and catalyst loading studies is provided. State-of-the-art Johnson Matthey catalysts were used in control experiments to demonstrate the utility of the array fuel cell for high throughput screening of fuel cell catalysts in the 3-4 mg/cm² range. This report lays out hard learned rules for high throughput screening and demonstrates that the array fuel cell can be used for very precise screening of libraries of membrane electrode assembly (MEA) components without the pitfalls discussed in the introduction.