求解二维结构-声耦合问题的一种直接方法

本文基于传递矩阵法(TMM)和虚拟边界元法(VBEM)，提出了一种求解在谐激励作用下二维结构-声耦合问题的直接法。文中对任意形状的二维弹性环建立了一阶非齐次运动微分方程组，便于用齐次扩容精细积分法求解，对于含有任意形状孔穴的无穷域流体介质的Helmholtz外问题，采用复数形式的Burton-Miller型组合层势法建立了虚拟边界元方程，保证了声压在全波数域内存在唯一解。根据叠加原理并结合最小二乘法，提出了一种耦合方程的直接解法，由于该方法不存在迭代过程，因而具有较高的计算精度和效率。文中给出了二个典型弹性环在集中谐激励力作用下声辐射算例，计算结果表明本文方法较通常采用的混合FE／BE法更为有效。     

Measurement and Identification of the Parameters of SPICE-Models of a Bipolar Transistor

A method of measuring and identifying the static parameters of a bipolar transistor is considered. The characteristic of the transistor, from which the parameters of the model are determined, is chosen depending on what group the calculated parameters belong to. The characteristics are measured in such a way that the equations of the model describing them can be reduced to the simplest form.     

基于模式理论光栅椭偏参数反演的数值模拟

将一种广泛用于求解系统优化问题的方法——正单纯形法，求解光栅的椭偏方程。首先，利用求解光栅的傅立叶模式理论对TE和TM波的复反射系数进行求解。然后计算出其相应的椭偏参数(△，Ψ)，并在该值的基础上加入不同偏差的随机高斯噪声，将加入噪声后的值(△m，Ψm)作为模拟测量值。最后使用优化算法进行反演。通过对几种常用面形光栅椭偏参数的数值模拟，一方面表明傅立叶模式理论计算光栅的椭偏参数不仅精度高。而且速度快；另一方面表明利用正单纯形法得到的光栅参数值很接近于正演时假设的参数值，从而从理论上证明了利用椭偏法测量光栅各种光学参数的可行性。     

钻井参数仪的模块化设计方法研究

文章以模块化设计原理为基础，讨论了钻井参数仪的模块划分，模块化设计准则和主要设计内容。采用模块化设计方法、现场设备网络的开放网络和现场总线解决方案设计的钻井参数仪，具有传输信号稳定、可靠性高、抑制噪声能力强、组建现场网络成本低等特点。     

复合材料手动扫描超声特征成像检测

研究了复合材料手动扫描超声特征成像检测，通过对超声检测信号的全波列采集与处理，实现了A，B，C扫描成像；相位特征成像；当量特征成像；超声层析技术和超声频谱分析技术。该系统已经在复合材料的检测上得到了良好的应用。     

带参数的一阶脉冲微分方程边值问题

利用上下解和单调迭代法。讨论了带参数的一阶脉冲微分方程。获得了单边Lipschitz条件下这类方程边值问题的解的存在性。     

Texture Changes During the Ripening of Port Salut Argentino Cheese in 2 Sampling Zones

ABSTRACT: Texture changes during ripening of Port Salut Argentino cheese for different sampling zones were studied. Compression relaxation tests were performed and results were analyzed using both Maxwellian and Peleg's models. Elastic equilibrium modulus obtained from the Maxwellian model decreased from 1.22 to 0.11 10⁴Pa during ripening. The constants derived from Peleg's model, k₁ and k₂, diminished with ripening time from 1.18 to 0.71 min and from 1.27 to 1.12, respectively. Asymptotic equilibrium modulus from Peleg's model decreased from 0.95 to 0.07 10⁴Pa during ripening. Rate parameters derived from a 1st order kinetics applied to both equilibrium moduli showed that the decrease was faster in the external zone (0.0846 d⁻¹) than in the central zone (0.0368 d⁻¹). The correlation between equilibrium moduli, salt concentration, moisture content, and maturation indexes was obtained with a determination coefficient of 0.76.     

Growth Stresses in the Oxide Scales on TiAl Alloys at 800 and 900°C

In the oxidation of TiAl alloys, the role of scale-growth stresses formed during oxidation has, thus far, been unknown. In the present paper the oxide-growth stresses were investigated by the deflection-test method in monofacial oxidation (DTMO) accompanied by acoustic-emission measurements. On unmodified surfaces the growth stresses are compressive and reach levels of around –100 MPa. At the same time, significant acoustic emission occurs indicating that even under isothermal conditions, stresses are relieved by a scale-cracking mechanism. For oxide scales on TiAl surfaces, which had been ion implanted with chlorine before oxidation, a very thin protective alumina layer is formed which, however, develops growth stresses in the range of several GPa, accompanied by intensive acoustic emission. In all stress–time curves, a dynamic situation is observed. This consists of phases of stress relief by scale microcracking and phases of stresses increase due to crack healing and further oxide growth. As a result, the level of stress as a function of oxidation time, is characterized by an oscillating course.     

Acoustic emission method for research and control of friction pairs

One of the new physical methods that provides much information about the processes going on in a friction contact zone in real time is acoustic emission (AE). Basic experimental results of AE in friction are presented and analysed. Using AE signals we can get an indication about the state of the friction processes, about the quality of solid and liquid layers on the contacting surfaces in real time, sometimes about intensity of wear, changing of wear and friction regimes and so on. The influence of sliding velocity, load, roughness and some physical and mechanical properties of the body on the parameters of AE are also given. Some attention to the practical implementation of these techniques for control of capability for work of friction pairs in real conditions are given. Modern methods and devices enable condition monitoring of sliding and rolling bearings.     

Addition of pectolytic enzymes: an enological practice which improves the chromaticity and stability of red wines

Summary The effect of the addition of four commercial pectolytic preparations on the visual characteristics (colour and turbidity) of red wines has been evaluated. The effect of both clarifying and colour extracting enzymes and the effect of different doses used, were evaluated and compared. All the red wines treated enzymatically, independent of the type of enzyme and dose, present chromatic characteristics which can be considered better than those of the control wines. Also, those wines treated with enzymes had greater stability during 2 years storage in bottles, in particular the turbidity was better than untreated wines.