Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

电缆气压保气率计算机统计系统

介绍了电缆气压保气率计算机统计系统开发的目的和意义，系统程序的流程和结构，以及系统程序的编制和应用。     

智能混合控制在高速纸机的应用

介绍了压力式网前箱的建模和控制，并通过构造一个新的控制器结构-智能混合控制器，将Fuzzy和PID控制融于其中。     

Analysis of low load transients for the Vandellòs-II NPP: Application to operation and control support

The Technical University of Catalonia (UPC) has been jointly working with the Asociación Nuclear Ascó-Vandellòs (ANAV) for a number of years in order to establish, qualify and use best estimate (BE) models for the reactors under the control of ANAV. ANAV is the consortium that is responsible for operation of the Ascó and Vandellòs-II reactors. The reactors are Westinghouse-design three-loop PWRs with an approximate electrical power of 1000 MW. The existing integral plant models for each plant are currently used for many different purposes among which are support of plant operation and control. Quite a number of studies have been done in order to improve both safety and plant competitiveness. Most of these dynamic analyses were carried out in relation to transients starting at nominal full power or at least, very close to full power. This paper develops a specific use of the Vandellòs-II plant model for operation and control support at low power involving new ranges of system actuation parameters. It also examines scenarios that are somewhat different from those typically analysed. The study starts showing the results of an assessment case, which is a start-up test and provides some additional qualification, and subsequently attempts to establish calculations to support both an improvement in feed water controls and to set up operating recommendations for low-load manual operation of feed water turbo-pump. Both results hopefully, will produce an outcome, which leads to an improvement in safety and reduces reactor trip probability.     

Characterizing steel tube for hydroforming applications

With the increased use of tubular steel products, especially for hydroforming applications, it is important to be able to predict the performance of tube from sheet tensile tests. In the present study, two aluminum killed draw quality (AKDQ) steels and one high strength low alloy (HSLA) steel were evaluated. Tensile properties and plastic strain ratios were measured on sheet material in the longitudinal and transverse directions. Axial tensile tests were performed on material extracted from production tubes. Material from quasi tubes, which are strip material bent to the same curvature as the tubes but not welded or sized, was also tested. Residual stresses in the production and quasi tube were determined by displacement methods. A hydraulic burst test was performed on the production tubes to simulate a hydroforming operation. Effective strains resulting from tubemaking are calculated for two discrete operations: bending and sizing. For the production tubes, a linear relationship was found between a load factor (strength times thickness) and effective sizing strain. The relationship between load factor and residual stress was also linear. Predictions of the maximum pressure and the strain at instability during a hydraulic burst test are shown to compare favorably with experimental values, based on flat sheet properties and tubemaking strains. The prediction of the yield strength in the tube based on flat sheet properties is shown to be fairly accurate when the effective sizing strain is small compared to the effective bending strain.     

对甲醇精馏几个问题的认识

简述甲醇精馏三塔流程原理 ,分析了加压精馏塔及常压精馏塔物料和热量平衡关系 ,提出了操作中应注意的事项     

啤酒废水处理技术研究

采用压力生物氧化－气浮组合工艺处理啤酒废水。试验结果表明，在适当条件下，进水ＣＯＤ为１６３０－２３６０，ｇ／Ｌ，生化反应容积负荷１２．３－１５．６ｋｇＣＯＤ／Ｍ＾３．ｄ，气浮水力负荷２８．８－５２．９ｍ＾２／ｍ＾２．ｄ，出水达现有企业一级排放标准。     

现场总线技术在非能动压水堆核岛中的应用

本文结合非能动压水堆核电控制系统结构,详细介绍Profibus现场总线和Modbus现场总线在非能动压水堆核电控制系统中的应用,包括两种现场总线技术的结构配置及和现场智能仪控设备的连接,并简要分析现场总线技术在核电行业应用的优点和需克服的技术问题。     

1000MW压水堆核电机组一回路充排水过程中水位测量仪表偏差分析

应用流体力学中关于管道流动阻力的理论,分析1000MW压水堆核电机组在常温常压下一回路排水过程中水位的变化情况,找出水位偏差大的原因,并提出解决这一问题的措施。     

板料双向加压液压胀形数值模拟

应用商用有限元软件ANSYS/LS-DYNA,对板料的双向加压液压胀形过程进行了数值模拟.并利用韧性断裂准则作为胀形高度极限的判断依据,将模拟得到的必要数据代入到准则中.对两种材料、不同初始液体压力条件下的模拟结果表明,随着初始液体压力的升高,胀形的极限高度也相应的增加,当初始压力与板料的强度相当时,极限高度提高的更明显.