Al、Mo含量对铸造钛合金力学性能的影响

运用正交实验 ,考察了Al、Mo含量对Ti Al Mo 1Zr系铸造钛合金力学性能的影响。试验结果表明 :随Al、Mo含量提高 ,铸造合金的强度增加 ,塑性和冲击韧性降低 ,但Al、Mo的交互作用却使合金塑性提高 ,强度和冲击韧性降低     

Model validation and model structure determination

This paper gives a tutorial overview of basic approaches for model validation and model structure determination.Work partially supported by the Swedish Research Council for Engineering Sciences under contract 98-654.     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

过氧化甲乙酮合成研究

论述了过氧化甲乙酮的合成方法，用阳离子交换树脂催化剂代替传统的无机酸催化剂。考察了离子交换树脂用量、反应温度对反应产率、活性氧含量的影响及溶剂对产品稳定性的影响。     

Simultaneous Spectrophotometric Determination of Three Components Including Deoxyschizandrin by Partial Least Squares Regression

1IntroductionWuweizi is a traditional Chinese herb,usually usedto cure cough,asthma,neurasthenic,hepatitisetc.Theactive ingredients in wuweizi are5%-22%lignan,themain components of which include deoxyschizandrin,schizandrin andγ-Schizandrin.Forthe purpos…     

Peracetic acid pretreatment of sugarcane bagasse for enzymatic hydrolysis: a continued work

Previous work has shown that the enzymatic hydrolysis of sugarcane bagasse could be greatly enhanced by peracetic acid (PAA) pretreatment. There are several factors affecting the enzymatic digestibility of the biomass, including lignin and hemicelluloses content, cellulose crystallinity, acetyl group content, accessible surface area and so on. The objective of this work is to analyze the mechanism of the enhancement of enzymatic digestibility caused by PAA pretreatment. Delignification resulted in an increase of the surface area and reduction of the irreversible absorption of cellulase, which helped to increase the enzymatic digestibility. The Fourier transform infrared (FTIR) spectrum showed that the absorption peaks of aromatic skeletal vibrations were weakened or disappeared after PAA pretreatment. However, the infrared crystallization index (N.O'KI) was increased. X‐ray diffraction (XRD) analysis indicated that the crystallinity of PAA‐treated samples was increased owing to the partial removal of amorphous lignin and hemicelluloses and probable physical change of cellulose. The effect of acetyl group content on enzymatic digestibility is negligible compared with the degree of delignification and crystallinity. The results indicate that enhancement of enzymatic digestibility of sugarcane bagasse by PAA pretreatment is achieved mainly by delignification and an increase in the surface area and exposure of cellulose fibers. Copyright © 2008 Society of Chemical Industry     

The influence of raw material characteristics on the industrial pelletizing process and pellet quality

Industrial pelletizing of sawdust was carried out as a designed experiment in the factors: sawdust moisture content, fractions of fresh pine, stored pine and spruce. The process parameters and response variables were energy consumption, pellet flow rate, pellet bulk density, durability and moisture content. The final data consisted of twelve industrial scale runs. Because of the many response variables, data evaluation was by principal component analysis of a 12 × 9 data matrix. The two principal component model showed a clustering of samples, with a good reproducibility of the center points. It also showed a positive correlation of energy consumption, bulk density and durability all negatively correlated to flow rate and moisture content. The stored pine was more related to high durability and bulk density. The role of the spruce fraction was unclear. The design matrix, augmented with the process parameters was a 12 × 6 matrix. Partial least squares regression showed excellent results for pellet moisture content and bulk density. The model for durability was promising. A 12 × 21 data matrix of fatty- and resin acid concentrations measured by GC–MS showed the differences between fresh and stored pine very clearly. The influence of the spruce fraction was less clear. However, the influence of the fatty- and resin acids on the pelletizing process could not be confirmed, indicating that other differences between fresh and stored pine sawdust have to be investigated. This work shows that it is possible to design the pelletizing process for moderate energy consumption and high pellet quality.     

A novel method for determination of polyester end-groups by NMR spectroscopy

An efficient, convenient and quantitative method for characterising polyester end-groups is described. We have found that trichloroacetyl isocyanate (TAI) reacts rapidly and quantitatively with both carboxyl [C(O)OH] and hydroxyl (OH) chain ends to form derivatives that can be readily determined by ¹H NMR spectroscopy. The TAI capped end-groups give rise to characteristic imidic NH resonances in a normally clear region of the ¹H NMR spectrum [δ∼10-11.5 for C(O)-O-C(O)-NH-C(O)CCl₃ from C(O)OH, δ∼8-9 for O-C(O)-NH-C(O)CCl₃ from OH]. The method has been successfully applied to quantitative determination of the end-groups of a wide variety of oligomeric polyesters. It has also been applied to higher molecular weight polyesters including commercial, bottle grade, poly(ethylene terephthalate) (PET) and PET based copolyesters (e.g. PETG).     

直流电动机参数测定

根据直流电机的可逆原理并利用常规的实验仪表，可以简便、准确地测出直流电动机的主要参数－电磁转矩、输出转矩和效率．     

F级高云母含量云母带的研制及应用

本文介绍了一种F级高云母含量云母带，它的主要特点是云母含量高达48％以上，具有良好的长时间耐电热老化性能，适用于高压电机主绝缘多胶模压工艺要求，该云母带的应用对提高电机绝缘水平和延长电机使用寿命具有重要意义。