Numerical analysis of two-dimensional steady-state and transient heat transfer in a parallel duct filled with pressurized He II

Analysis on steady-state and transient heat transfer on a flat plate at the middle of a parallel duct immersed in He II was performed for bath temperatures from 1.8 to 2.1 K at 101.3 kPa. Two-dimensional computer code named SUPER-2D developed by the authors based on the two-fluid model and the theory of mutual friction was used. Steady-state critical heat flux (CHF) and the time lag from the application of a step heat input to λ transition, that is called a lifetime, were obtained numerically for various step heat fluxes and for the channel gaps from 2 to 20 mm. Effect of the gap restriction on the CHF and the lifetime were clarified. The solutions were compared with the experimental data for the ducts with the same structures and the corresponding conditions. They agreed well with the experimental data. The heat transport mechanism in the parallel duct was clarified.     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

ABB变频器在双馈发电机试验台上的应用

本文介绍了风力发电系统目前存在的技术方案，重点介绍了ABB用于双馈式风力发电系统的变频产品ACS800—67的特性，并对由其构建的发电机测试平台的案例进行了实验分析。     

汽轮机回热系统给水焓升的最优分配

从汽轮机回热系统的实际情况出发，运用非线性规划理论和计算机技术，解决了给水焓升设计中的最优分配问题。结合具体实例，针对国产200MW汽轮机回热系统给水焓升的分配进行了说明。     

未来航空润滑油基础油

介绍了未来航空涡轮发动机对润滑油性能的要求:在260,-54℃时,试样运动黏度分别大于1.0 mm2/s和小于15 000 mm2/s,热氧化安定性温度为260~427℃。该要求已超出了目前使用的酯类润滑油所能承受的最大极限。为了满足要求,需开发全氟聚醚、改性硅油、聚苯醚、C-型醚、氟醚三嗪及环三磷偶氮润滑油基础油,它们的使用温度依次为:-34~316,-60~260,5~288,-29~260,-30~343,-15~343℃。     

汽轮机数字电液控制系统及其应用

介绍了汽轮机数字电液控制系统（DEH）的硬件组成，着重论述了DEH的控制原理和控制过程。结合天津碱厂新建4^#机组,与前3台机组的液压控制调节方式进行比较，突出了DEH控制的优势。对DEH系统的软件作了介绍。同时对DEH的控制系统Foxboro I／A Series的系统软件和系统网络作了较详细的论述。最后，讨论了运行中可能出现的问题和解决方法。     

反水锤的危害及防止

反水锤是发生在反击式水轮机尾水道中的一种特殊水锤现象，其压力峰值可达正常压力的几倍，甚至十多倍，以致造成肢解转轮、折断导叶、破坏顶盖、抬起转子的严重事故。因此，研究反水锤发生的原因，从而提出防止反水锤事故的措施尤为重要。     

Lowering the erosion wear of long blades of the last stages by optimum hanging

Problems of optimum hanging of long rotor blades of the last stages of steam turbines are considered. Causes of nonuniform erosion wear of the inlet edges connected with inaccurate location of holes for the external damper coupling on the chord of the profile are determined. Methods for optimizing the hanging of blades for raising the reliability of the last stages are suggested. Main results of hanging performed with the help of a specially developed “LIBRA” soft hardware are presented. __________ Translated from élektricheskie Stantsii, No. 11, November 2006, pp. 36–41.     

水平轴风力机的几个关键气动问题探讨

水平轴风力机是最有效的风能转换装置之一 ,在世界各地得到了广泛的应用。本文讨论了在风力机的研究和开发过程中所遇到的几个关键气动问题 ,在分析这些问题产生原因的基础上 ,介绍了目前的研究现状和研究水平。本文并结合问题所涉及的基本理论 ,以及学科发展的趋势 ,提出了解决问题的基本方法 ,以及发展方向和近期可望达到的目标等     

现场总线技术在发电系统数据采集中的应用

介绍了现场总线网络在干熄焦汽轮机发电生产过程中所起的作用，并重点介绍了系统所完成的数据采集，监视和管理等功能。