MoSi2发热体在熔铝炉中的运用

以电阻熔铝炉技术改造实践为例，介绍一种高效、节能、不渗铁的新型熔铝炉——二硅化钼熔铝炉的设计。     

聚苯硫醚复合涂层的耐磨性能

研究了用固体润滑石墨、碳化硅、二硫化钼等填料改性的聚苯硫醚 (PPS)涂层的耐磨性能。实验结果表明 ,聚苯硫醚复合涂层具有优良的耐磨性 ;加入适量 ( 3 0 % )的石墨、碳化硅等固体润滑剂 (石墨 :碳化硅 =2∶3 ) ,可以有效提高涂层的耐磨性能 ,而二硫化钼和三氧化二铬的减摩效果更佳     

灰铸铁石墨形态的研究

文本研究了化学成份与冷却速度及孕育处理对灰铸铁石、墨形态的影响．并对形成的地B、C、D、E、F等六种衣铸铁石墨形态的形成条件作了讨论．     

Methacryloxyethyl phosphate‐grafted expanded polytetrafluoroethylene membranes for biomedical applications

Expanded polytetrafluoroethylene (ePTFE) membranes were modified by graft copolymerization with methacryloxyethyl phosphate (MOEP) in methanol and 2‐butanone (methyl ethyl ketone (MEK)) at ambient temperature using gamma irradiation. The effect of dose rate (0.46 and 4.6 kGy h^?1), monomer concentration (1–40 %) and solvent were studied and the modified membranes were characterized by weight increase, X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XPS was used to determine the % degree of surface coverage using the C? F (ePTFE membrane) and the C? C (MOEP graft copolymer) peaks. Grafting yield, as well as surface coverage, were found to increase with increasing monomer concentration and were significantly higher for samples grafted in MEK than in methanol solution. SEM images showed distinctly different surface morphologies for the membranes grafted in methanol (smooth) and MEK (globular), hence indicating phase separation of the homopolymer in MEK. We propose that in our system, the non‐solvent properties of MEK for the homopolymer play a more important role than solvent chain transfer reactions in determining grafting outcomes. Copyright © 2005 Society of Chemical Industry     

在湿陷性黄土地区对混凝土夯扩桩的检测

对夯扩桩在豫西湿陷性黄土地区的应用和可行性分析与检测。     

Role of RE and Mg on Graphitization of Spheroidal Graphite Malleable Cast Iron

ＲｏｌｅｏｆＲＥａｎｄＭｇｏｎＧｒａｐｈｉｔｉｚａｔｉｏｎｏｆＳｐｈｅｒｏｉｄａｌＧｒａｐｈｉｔｅＭａｌｌｅａｂｌｅＣａｓｔＩｒｏｎ￥ＬｉｕＪｉｎ－Ｈａｉ（ＨｅｂｅｉＩｎｓｔｉｔｕｔｅｏｆＴｅｃｈｎｏｔｏｇｙ，Ｍｉａｎｊｉｎ３００１３０，Ｃｈｉｎａ）...     

Ermüdungsverhalten und Dauerfestigkeit von Graphit und Aluminium – infiltriertem Graphit

Fatigue behaviour and endurance limit of graphite and of aluminium‐infiltrated graphite Fatigue properties of polycrystalline, isotropic graphite FU2590 and of FU2590 infiltrated with AlSi7Mg (FU2590/AlSi7Mg) were investigated in reversed bending tests at 25 Hz at numbers of cycles below 10⁷ and in tension‐compression tests at 20 kHz below 10⁹ cycles. The open porosity of Graphite (10‐11 Vol.‐%) was infiltrated with the aluminium alloy using the squeeze casting infiltration method, which led to an increase of the bending strength by 50 %, increase of tensile strength by 30 % and increase of stiffness by 15 %. Fully reversed tension‐compression loading of FU2590 delivers a mean endurance limit at 10⁹ cycles at the normalized maximum stresses (i.e. maximum tension stress of a cycle divided by the static strength) of 0,65±0,03. Mean numbers of cycles to failure of 10⁴ were found in fully reversed bending tests at the normalized maximum stress of 0,78. The infiltrated material shows approximately 30 % higher cyclic strength in reversed bending tests, and the mean endurance limit under tension compression loading increases by 15 %. The increased endurance limit of the infiltrated material is caused by the increased stiffness. The increased toughness of graphite due to the infiltration with aluminium is of additional beneficial influence at the higher cyclic stresses investigated in reversed bending tests and in static tests.     

A Simple Quasi-2D Numerical Model of a Thermogage Furnace

A simple quasi-2D model for the temperature distribution in a graphite tube furnace is presented. The model is used to estimate the temperature gradients in the furnace at temperatures above which contact sensors can be used, and to assist in the redesign of the furnace heater element to improve the temperature gradients. The Thermogage graphite tube furnace is commonly used in many NMIs as a blackbody source for radiation thermometer calibration and as a spectral irradiance standard. Although the design is robust, easy to operate and can change temperature rapidly, it is limited by its effective emissivity of typically 99.5–99.8%. At NMIA, the temperature gradient along the tube is assessed using thermocouples up to about 1,500°C, and the blackbody emissivity is calculated from this. However, at higher operating temperatures (up to 2,900°C), it is impractical to measure the gradient, and we propose to numerically model the temperature distributions used to calculate emissivity. In another paper at this conference, the model is used to design an optimized heater tube with improved temperature gradients. In the model presented here, the 2-D temperature distribution is simplified to separate the axial and radial temperature distributions within the heater tube and the surrounding insulation. Literature data for the temperature dependence of the electrical and thermal conductivities of the graphite tube were coupled to models for the thermal conductivity of the felt insulation, particularly including the effects of allowing for a gas mixture in the insulation. Experimental measurements of the temperature profile up to 1,500°C and radial heat fluxes up to 2,200°C were compared to the theoretical predictions of the model and good agreement was obtained.     

制备低硫可膨胀石墨的研究

研究了以过二硫酸铵作氧化剂低硫可膨胀石墨的制备，找到了在较低温度下，制备低硫可膨胀石墨的最佳条件。即过二硫酸铵和石墨的重量比为１５％；反应温度为５５℃；反应时间为４０ｍｉｎ；硫酸浓度为９８％；硫酸与石墨的重量比为４∶１，草酸和硝酸（浓度为６５％）的重量比为７．５％时，所制得的可膨胀石墨含硫量为０．６５％，膨胀容积为２００ｍＬ／ｇ可膨胀石墨。并且，其终端产品柔性石墨具有优良的力学性能和抗氧化性能。     

真空阴极弧离子镀类金刚石碳（DLC）膜的碳弧稳定性研究

选用氩气、氩气加氢气、氩气加乙炔等气体作为介质，石墨作为靶材进行真空阴极弧离子镀来制备类金刚石碳膜。石墨电弧有其独特的电弧特性曲线，不同气体介质对碳弧特性的影响不同，磁场的大小对电弧的稳定性有很大作用，碳弧下基片偏流随电弧电压的增加而减小，试验得到表面光滑的类金刚石碳（DLC）膜，对膜的表面进行了SEM分析。