多带OFDM-UWB系统峰均功率比降低方法研究

针对多带OFDM—UWB信号存在高峰均功率比的问题，提出了利用扩展与交织降低系统信号峰均功率比的方法。该方法通过对传输数据进行正交扩展与交织，使得进入多载波调制的数据趋于高斯分布，减小了传输数据自相关函数的旁瓣峰值，降低了OFDM-UWB信号的峰均功率比。由于采用正交矩阵进行扩展，扩展前后的数据传输速率保持不变。仿真结果表明，扩展与交织可以有效地降低信号峰均功率比2-5dB左右。同时该方法还具有抗窄带干扰的鲁棒性。     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

沙漠地区高精度地震资料处理技术

受静校正及各种类型干扰的影响,西部沙漠地区地震资料的高精度处理较东部地区有更大的难度。对准噶尔盆地中部Ⅱ区、Ⅲ区、Ⅳ区、顺托果勒等区块地震资料在振幅恢复、静校正、去除各类噪音、高精度速度分析及叠前、叠后子波处理等方面进行了大量的试验与研究,形成了较为系统的高精度地震资料处理技术,在西部不同区块地震资料处理中取得了较好的应用效果。     

双级染料激光放大器泵浦能量分配的数值研究

用染料激光放大器的横向稳态泵浦理论，对不同的入射光能量选择不同的增益计算方法，研究了双级染料放大器的泵浦能量分配比例、泵浦光总能量和信号光能量大小对激光增益的影响。计算结果表明，对于其他参数确定的放大系统，存在着最佳的泵浦能量分配比例，可获得最大增益输出。通过自编程序的计算，可方便地找出特定系统泵浦能量分配比例的最佳值。     

Cs-K混合蒸气中Cs(8D)+K(4S)碰撞能量转移

在Cs-K混合蒸气中，两步激发Cs原子到8D态，观察了Cs(8D) K(4S)→Cs(5D) K(4P)碰撞能量合并逆过程(REP，reverse energy pooling)。应用双调制技术探测K(4P)原子发射的荧光，基态K原子密度用光学吸收方法测量。得到了REP速率系数，讨论了其它过程对速率系数的影响．     

The correlation of texture and magnetic properties in Co-Cr films

This investigation focuses on the correlation between the crystallographic orientation of grains with respect to magnetic properties in Co-Cr films. Based on a distribution measured for the (0002) crystallographic pole densities, modified formulae describing the texture were used to calculate the coercivity Hc, the squareness ratio Rs (Mr⊥/TMs) and the anisotropy field Ha for Co-Cr films. In general, calculated values for the coercive force He agreed well with the measured values. The calculated Rs⊥. values were much larger than the measured ones, however, indicating that the influence of the demagnetizing field and the magnetostriction on the orientation of the magnetization cannot be neglected. On leave from Institute of Computing Technology, Academia Sinica, P.O.Box 2704-6, Beijing, P.R. China.     

Constant thrust programming for a multistage rocket flown in vacuum with a given initial/final thrust-to-weight ratio in an arbitrary stage

The burn time and burnout velocity of a multistage rocket flown vertically in vacuum with constant thrust tangential to the flight path and a prescribed initial/final thrust-to-weight ratio in an arbitrary stage have been determined. The present paper also deals with optimal staging under given conditions of flight.     

Voltage sag compensation with minimum energy injection by use of a micro‐SMES

This paper presents a method to compensate voltage sags with minimum energy injection for a series‐connected voltage restorer using a micro‐SMES. A circuit for extracting the fundamental symmetrical components from sag voltages and a minimum energy injection algorithm is described. Simulations of voltage sag compensation have been carried out using PSCAD/EMTDC for various faults. The simulation results confirm the validity of the proposed method and show the possibility of reducing the size of energy storage devices. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(3): 70–80, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10047     

深穿透复合射孔技术在中原油田的应用

深穿透复合射孔是一项把射孔与高能气体压裂两种技术有机地结合在一起的综合改造油气层的新技术。重点对它的技术原理，包括设计原理、枪身内火药燃烧气体对射孔孔眼的冲刷作用原理、火药燃烧气体射流的高能气体压裂作用原理等进行了研究与探讨，同时对它的施工工艺、现场应用等方面进行了阐述，经中原油田189口井现场应用证明，其工艺简便，成本低廉，可实现多层跨隔层使用，处理后增产效果显著，投入产出比高，可代替传统的聚能射孔技术，具有广阔的推广和应用价值。     

Modelling the impact of energy taxation

Energy taxation in Sweden is complicated and strongly guides and governs district energy production. Consequently, there is a need for methods for accurate calculation and analysis of effects that different energy tax schemes may have on district energy utilities. Here, a practicable method to analyse influence of such governmental policy measures is demonstrated. The Swedish Government has for some years now been working on a reform of energy taxation, and during this process, several interest groups have expressed their own proposals for improving and developing the system of energy taxation. Together with the present system of taxation, four new alternatives, including the proposed directive of the European Commission, are outlined in the paper. In a case study, an analysis is made of how the different tax alternatives may influence the choice of profitable investments and use of energy carriers in a medium‐sized district‐heating utility. The calculations are made with a linear‐programming model framework. By calculating suitable types and sizes of new investments, if any, and the operation of existing and potential plants, total energy costs are minimized. Results of the analysis include the most profitable investments, which fuel should be used, roughly when during a year plants should be in operation, and at what output. In most scenarios, the most profitable measure is to invest in a waste incineration plant. However, a crucial assumption is, with reference to the new Swedish waste disposal act, a significant income from incinerating refuse. Without this income, different tax schemes result in different technical solutions being most profitable. An investment in cogeneration seems possible in only one scenario. It is also found that particular features of some alternatives seem to oppose both main governmental policy goals, and intentions of the district heating company. Copyright © 2002 John Wiley & Sons, Ltd.