Scale Up from Small Oven-Drying Tests of Mineral Concentrate to Pilot-Scale Drying with a Heated Pad

While Fickian diffusion models are commonly used in other applications, there are few reports of them being applied to the batch drying of a mineral concentrate. Diffusion coefficients estimated from small-scale oven-drying tests were used to predict the drying behavior of a concentrate sample 1 m × 1 m in area and 50 cm deep, with a heated bottom pad. These pilot-scale tests included both daily turning of the sample and turning every three days. The excellent quantitative agreement between the predicted and observed pilot-scale behavior gives a high level of confidence in the model predictions and suggests that a Fickian diffusion model is adequate to predict the behavior of mineral concentrates at the low moisture contents used here.     

Preparation, Characterisation and Catalytic Behaviour of a New TeVMoO Crystalline Phase

TeM_xMo_1.7O mixed oxides (M = V and/or Nb; x = 0-1.7) have been prepared by calcination of the corresponding salts at 600 °C in an atmosphere of N₂. A new crystalline phase, with a Te/V/Mo atomic ratio of 1/0.2-1.5/1.7, has been isolated and characterised by XRD and IR spectroscopy. This phase is observed in the TeVMo or TeVNbMo mixed oxide but not in the TeNbMo mixed oxide. The new crystalline phase shows an XRD pattern similar to Sb₄Mo₁₀O₃₁ and probably corresponds to the M1 phase recently proposed by Aouine et al. (Chem. Commun. 1180, 2001) to be present in the active and selective MoVTeNbO catalysts. Although these catalysts present a very low activity in the propane oxidation, they are active and selective in the oxidation of propene to acrolein and/or acrylic acid. However, the product distribution depends on the catalyst composition. Acrolein or acrylic acid can be selectively obtained from propene on Nb-free or Nb-containing TeVMo catalysts, respectively. The presence of both V and Nb, in addition to Mo and Te, appears to be important in the formation of acrylic acid from propene.     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

聚苯硫醚复合涂层的耐磨性能

研究了用固体润滑石墨、碳化硅、二硫化钼等填料改性的聚苯硫醚 (PPS)涂层的耐磨性能。实验结果表明 ,聚苯硫醚复合涂层具有优良的耐磨性 ;加入适量 ( 3 0 % )的石墨、碳化硅等固体润滑剂 (石墨 :碳化硅 =2∶3 ) ,可以有效提高涂层的耐磨性能 ,而二硫化钼和三氧化二铬的减摩效果更佳     

钛精矿回转窑直接还原过程结圈可能性的探讨

通过煤种，入窑球冷态强度和还原过程强度，以及钛精矿与煤灰混合物的软化温度等分析探讨了钛精矿预热球团回转窑直接还原产生结圈的可能性，获得了可以避免结圈的结论。     

影响铁精矿K2O、Na2O、SiO2含量的因素分析

用统计分析方法 ,分析了影响精矿K2 O、Na2 O、SiO2 含量的因素 ,并根据分析结论提出了对生产工艺进行定向控制的条件     

硫氰酸铵光度法测定钒渣中钼量

研究了钒渣中钼与硫氰酸铵的显色反应，结果表明λmax=460nm，在0～50mg／50ml范围内吸光度与钼量的关系符合比尔定律，用于钒渣中钼的测定，结果令人满意。     

钼顶头破坏行为及强韧化分析

通过对钼顶头破坏行为的分析，说明了钼顶头破坏的主要原因。并进一步通过对钼顶头强韧化的分析，阐述了钼顶头延长使用寿命的措施，并制定了钼顶头生产工艺。     

Wear resistance of plasma coatings for a constant work of friction

We analyze the wear resistance of plasma coatings for a constant work of friction. The dependences of the wear resistance of the coatings are obtained for a broad range of loading conditions. It is shown that the minimum sensitivity to loading conditions is exhibited by the molybdenum coatings. It is also established that the wear resistance of the coatings decreases as the amplitude of displacements increases and the cyclic frequency of the tests decreases due to the intensification of fatigue processes on the surfaces. The comparative characteristics of coatings are presented. __________ Translated from Problemy Prochnosti, No. 5, pp. 94–100, September–October, 2007.     

Ni-Mo-O催化剂中协同作用对丙烷氧化脱氢的影响

在 Ni-Mo-O体系中 ,加入 Mo O3 能极大地提高丙烷氧化脱氢制丙烯的反应活性。选用固混法、沉淀法、柠檬酸法制备了 Mo O3 过量 1 5 % (摩尔分数 )的α -Ni Mo O4催化剂 ,其中用沉淀法制得催化剂在 5 0 0℃ ,V( C3 H8) /V ( O2 ) /V ( N2 ) =1 0 /1 0 /5 0 ,反应气流量为 70 m L/min的条件下丙烷转化率可达 38.7% ,丙烯选择性达 70 .1 4 %。经 XRD,XPS,TPR表征说明 ,在含有过量 Mo O3 的催化剂中 ,α -Ni Mo O4与 Mo O3 两种晶体之间可产生微小的相互吸引 ;从而发挥协同作用 ,是提高催化剂活性