Stress-deformable state of isotropic double curved shell with internal cracks and a circular hole

This work is devoted to the stress–strain state of isotropic double curved shell with defect system. The construction is weakened by two non-through thickness (internal) cracks of different length and by a circular hole located between cracks. In this study we use the line-spring model. Within the framework of this model cracks are modeled as mathematical cuts of shell’s middle surface. This leads to a two-dimensional problem. The problem is reduced to a system of eight boundary integral equations. To ensure the uniqueness of solution an additional equation is added. In the numerical solution of the problem special quadrature formulas for singular integrals of Cauchy type and the finite difference method are applied. The influence of defects on each other for double curved shell has been investigated. The given theoretical results can be used for the calculation of structural elements with holes, cracks on the strength and fracture toughness in various branches of engineering.     

冷轧平整机机前甩尾轧制工艺的开发与应用

本文介绍了柳钢冷轧板带厂1550 mm单机架平整机机前甩尾轧制的工艺。改进前轧制每卷钢卷生产效率低,钢卷成材率低,改进后生产效率、成材率明显提高,部分规格的钢卷能实现带尾剪切长度为零。     

Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

乐滩灌区输水隧洞穿合山煤矿采空区处理设计

分析了乐滩灌区工程北干渠溯河隧洞段长约1.06 km穿合山煤矿采空区的地质情况.借鉴高速公路煤矿采空区的成功处理经验,通过科学分析,对采空区变形和区域内覆岩的稳定性做了评价,论述了输水线路穿采空区段采取全充填压力注浆法的工程处理方法.     

挖金湾矿近距离煤层联合布置开采可行性研究

提出挖金湾矿近距离煤层联合布置开采方案，并对开采方案的技术难点进行了分析，找出了解决方法。     

井巷掘进控制斜形炮孔钻孔精度的试验研究

井巷掘进爆破工程中，工作面按设计要求，布置各种斜形炮孔，利用量角器和垂直尺控制钎杆与工作面夹角，使炮孔钻孔精度与设计炮孔角度基本上符合，在生产中取得了良好的爆破效果．     

套管固井质量问题及对策分析

从油田现场反应的情况出发，对调整井固井，尾管固井，大位移井套管固井和其他固井的质量问题进行了分析，针对各种问题产生的原因，提出了相应换解决办法。     

长25-29井卡钻事故的处理

长２５－２９井在完井阶段通井过程中发生粘附卡钻事故，在处理卡钻过程中又发生卡套铣筒、井漏、溢流等事故及复杂情况。通过对井下情况的认真分析，采取先堵漏后循环再解卡的处理方案，顺利地解除了该次卡钻事故，大大地减少了经济损失。     

晶须取向对SiCw／Al复合材料切削表面质量的影响

切削与晶须取向方向间的夹角对ＳｉＣｗ／Ａｌ复合材料切削表面质量有很大影响。当切削角为４５°时，晶须拔出和转动现象均较少，复合材料切削表面粗糙度最低。当切削角为１３５度时，晶段转动造成的撕裂破坏程度很大，复合材料切削表面粗糙度最大。     

矩形件排样的一种优化算法

排样问题是一种总体资源分配问题，这里根据矩形件排样的工艺要求，提出了矩形件排样的一种近似算法，将一块板材分成三部分，每部分排一种零件，使得减料方便，提高了劳动生产率。