一种基于三次样条函数求离子浓度的自动算法

本文提出了一种用三次样条函数模拟双次标准加入法测量方程，直接求解离子浓度的自动算法。比较了三咱不同边界条件下用要池数计算离子浓度的结果。造出节点区间两极端点的二阶导数为零时的三次样条函数为最佳模拟函数。并讨论了该方法在实际分析中误差的来源及消除办法。经对一系列文献数据的验算对比，表明本法完全可代替传统的迭代法和查图法，且能方便地设置在智能化的电位分析系统中。     

用保形样条方法求解非定常对流扩散方程

在欧拉-拉格朗日分裂方法的基础上,本文发展了一种固定网格上的欧拉-拉格朗日分裂方法.保形样条方法(SPSM)被用来解决倒特征线插值问题.通过求解几个有精确解的例子,说明SPSM方法的解是单调无振荡的,并且数值耗散也是比较小的.     

齿轮磨前滚刀的齿形研究

本文介绍了磨前滚刀滚切齿轮的最大根切量和磨后的渐开线长度计算,并建立了数学模型。为更加直观起见,还建立了模拟滚齿的数学模型。并在实验的基础上提出了参考标准。     

热带钢连轧机工作辊温度场和热凸度预报模型

采用一种具有较高精度的样条有限条法对轧制过程中工作辊的温度场和热凸度进行计算和预报。结果证明，该模型理论计算值与现场实测值吻合较好，可以较准确地计算和预报热带钢连轧机工作辊的热凸度。     

优化双圆弧拟合

本文提出一种优化双圆弧拟合的新算法，它采用的方法是用改变双圆弧联结点的切线使双圆弧与样条曲线间的法向误差达到最小（或小于允许误差），与其他双圆弧拟合方法相比较，该算法计算简单，线性，并可消除拟合曲线的不稳定性，拟合效果快速，良好。可直接应用于雕塑曲面的ＣＮＣ加工中。     

Effect of thermophoresis on particle deposition rate from a natural convection flow onto a vertical wavy plate

This research discusses the impacts of the surface area that the wavy surface gets more than the flat plate upon the aerosol particle deposition. Starting from the full Navier–Stokes equation, the mathematical analysis takes the thermophoretic motion formed by the temperature gradient and the fluid thermal expansion into consideration, and converts the governing equations into the boundary layer equation by the simple coordinate transformation and non-similarity method, and then works out these equations by the Spline Alternating-Direction Implicit method (SADI). The numerical value result reveals that the average deposition effect of the wavy plate is greater than the flat plate and that the increasing rate is nearly equal to the value obtained by dividing the surface area that the wavy plate gets more than the flat plate by 2.2.     

Spline-regression estimation of the influence of exposure dose on cancer probability

Spline regression is used to analyze the influence of radiation on the cancer probability in a group of participants of Chernobyl accident mitigation, depending on the exposure dose. A new method is proposed to approximate modified polygons by linear splines with two nodes. An algorithm for the identification of a transition point is outlined. __________ Translated from Kibernetika i Sistemnyi Analiz, No. 3, pp. 168–176, May–June 2006.     

Development and implementation of a NURBS curve motion interpolator

This paper deals with the issues of development and implementation of a real-time NURBS interpolator for a six-axis robot. Using an open-architecture controller system as a testbed, a real-time NURBS curve interpolator was developed, implemented and tested. Sample runs were conducted with the resulting trajectories measured in real-time during robot motion. The resulting trajectories are analyzed, discussed and compared with those from a commonly used point-to-point approximation technique. The real-time NURBS curve interpolator's feasibility, advantages and related issues are also discussed.     

新型硬及极硬岩石反井镶齿盘型破岩滚刀的研究

对新型硬及极硬岩石反井镶齿盘型破岩滚刀的总体设计方案、CrMnMo空冷耐磨钢调质处理以及力学性能、镶嵌固齿和过盈量的确定等滚刀设计关键技术,进行了分析、试验和研究,并取得了相应的结论。     

台阶内花键套筒冷挤压工艺研究

分析了台阶内花键套筒的冷挤压工艺 ,制定出冷挤压件图 ,确定了挤压方案及工艺流程 ,对各工序变形程度进行了校核 ,并计算出了挤压力,同时对挤压模具的设计制造进行了简单的介绍。